Table of Contents
Advertisement
Quick Links
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the content of this documentation, its quality, performance, merchantability, or fitness for a
particular purpose. Information presented in this documentation has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. The information
contained in this documentation is subject to change without notice.
In no event will nMedia will be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if
advised of the possibility of such damages.
TRADEMARKS
All trademarks used in this user guide are the property of their respective owners.
COPYRIGHT
© 2006 by NMEDIA SYSTEM, INC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written permission of NMEDIA SYSTEM, INC.
TECHNICAL SUPPORT
If a problem arises with your system and no solution can be obtained from this user guide, please contact your place of purchase or local dealer.
REVISION HISTORY
V 1.0
August, 2005
Note:
This user guide is designed to provide the user a quick reference for chassis setup. We assume you need the information
regarding how to assemble the system, such as Motherboard, CPU, RAM Memory, Hard Drive, DVD ROM, Operating System...,
etc. Based on this assumption, we make this user guide of quick installation guide. Please follow the description step by step to
install the components. If you have any question in assembling the system, please refer your questions to the appropriate
Technical Support of the component vendors.
Safety Warning
Turn down the CPU Cooler Fan Speed through the Front Controller may create vital damage to CPU. Adjust
Fan Controller (CPU F.R.S.) appropriately according to the CPU instruction. (Minimum Fan Speed at 2000 is
recommended)
HOME THEATER PC CHASSIS
Model: HTPC 200 BA & SA
Color: Black & Silver
Quick Installation Guide
(U.S. & Canada Only)
"RESET" button is for LCD Module only
(CPU Fan Speed is default to minimum speed of 1800 to prevent CPU damage)
Version 1.0
Advertisement
Table of Contents
Summary of Contents for nMedia HTPC 200 BA
- Page 1 In no event will nMedia will be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages.
-
Page 2: Other Components
Overview Standard Components Equipped HTPC 200 chassis 2 x 60mm silent case fan; 1 x 80mm silent HDD fan Air duct - Constant fresh air to CPU and avoid hot air re-circulation All-in-one card reader - onboard USB port required Audio/Video capture module &... -
Page 3: Installation
Installation Flowchart (Basic Procedures) Open box Read installation guides Remove top cover Remove optical drive bracket Install motherboard Perform a quality check Connect cables Install internal IR receivers (if required) Install hard drive Install CPU & Cooler Install DIMM memory module Install power supply Install optical drive Replace cover... - Page 4 Connect front panel / LCD cables a) Connect Front USB 2.0, IEEE 1394 and Audio Connectors b) Connect PWR Switch Connect RESET Switch d) Connect Card Reader internal USB cable e) Connect LCD cables See below table for more details Connectors Step 1: Connect Front USB 2.0, IEEE 1394 and Audio Connectors See motherboard user manual for location and connection.
- Page 5 Install Internal MCE Receiver User can convert the external MCE receiver dongle internally by installing the receiver PCB on the MCE Receiver IR Rack that comes with the case. (Right below the optical drive rack) Unscrew the 2 thumb screws and take out the IR receiver rack Take out the MCE external receiver plastic enclosure by removing the two front rubber legs Carefully install the MCE receiver module to the rack (check rack to...
-
Page 6: Step 3: Install Hard Drive
CPU Fan Controller Connector Connect the CPU Cooler Fan to the CPU FAN front controller connector so that CPU Fan Speed can be controlled upfront. (Minimum fan speed at 2000 is recommended) “C/F SW” enables you to set temp display reading If your motherboard has the Auto Fan Speed Control capability, simply connect the 4 format when installing the system. -
Page 7: Lcd Module
d) to LCD PWR e) to optical drive Step 7: Install the optical drive Other Component Installation For other components, including hard drive; RAM; CPU & cooler; optical drive, video card, sound card, TV tuner card and operating system etc., plan the installation steps carefully, and follow the user manual and motherboard manual instruction to avoid damages. -
Page 8: Safety Instructions
• Carefully re-packaging is needed to avoid shipping damages • All warranties are subject to properly uses. Any human power damages return may be rejected according to warranty terms and conditions Copyright © 2006 NMEDIA SYSTEM, INC. All Right Reserved.