Insallation Controls; Accessing Installation Menu; Automatic Channel Scan (Retune); Manual Channel Scan - Bush ELED42240FHDCNTD3D Installation & Operating Instructions Manual

General TV Operation

Insallation Controls

Accessing Installation Menu

1. Press "MENU" button on the remote control and
" " or " "
select Installation by using
2. Press "OK" button and the Installation screen
will be displayed.

Automatic Channel Scan (Retune)

1. In the Installation menu, select "Automatic
Channel Scan (Retune)" by using
button and press OK button .
2. Options will be displayed. You can select options
" " or " "
by using and OK buttons.
Menu Operations
Digital Aerial: Searches and stores aerial DVB stations.
Digital Cable: Searches and stores cable DVB stations.
Analogue: Searches and stores analogue stations
Digital Aerial & Analogue: Searches and stores
aerial DVB and analogue stations.
Digital Cable & Analogue: Searches and stores
cable DVB and analogue stations.
3. :KHQHYHU \RX VHOHFW DQ DXWRPDWLF VHDUFK W\SH
and press OK EXWWRQ D FRQ¿UPDWLRQ VFUHHQ ZLOO
appear on the screen. To start installation process,
select Yes, to cancel select No by using
"
and "OK" button.
4. After auto channel scan type is set and
VHOHFWHG DQG FRQ¿UPHG LQVWDOODWLRQ SURFHVV ZLOO
start and progress bar will move along. If desired,
press "MENU" button to cancel process. In such
a case, located channels are not stored.

Manual Channel Scan

1. In the Installation menu, select "Manual Channel
" " "
Scan" by using or
OK button.
2. Manual Scan options screen will be displayed.
Select the desired "Search Type" using
" "
button. Manual search options will change
accordingly.
For any help concerning set up and use of your TV please call the Customer Helpline: 0044 845 604 0105
3. Enter the multiplex (for digital manual search),
frequency, polarization, symbol rate, network
channel scan, satellite options (for satellite
button.
manual search) or frequency number (for
analogue manual search) using the numeric
buttons and press OK button to start search.
Network Channel Scan
1. Select Network Channel Scan from the
installation menu by using
and press OK button. 2. Network Channel Scan
selection screen will be displayed. Select Digital
Aerial or Digital Cable and press OK button to
continue. Refer to the Initial Installation section
for more information on the process.

Analogue Fine Tune

1. Select "Analogue Fine Tune" from the Installation
" " " "
or
menu by using
$QDORJXH ¿QH WXQH VFUHHQ ZLOO EH GLVSOD\HG
available if there are no analogue channels, digital
channels and external sources stored.
2.
Press OK button to proceed. Use
EXWWRQ WR VHW )LQH 7XQH :KHQ ¿QLVKHG SUHVV OK
button again.

First Time Installation

Deletes all stored channels and settings, resets TV
WR IDFWRU\ VHWWLQJV DQG VWDUWV ¿UVW WLPH LQVWDOODWLRQ
1. Select First Time Installation option and press
OK button if you would like to reset the TV.
2. A warning screen will be displayed. Select YES
and press OK to continue. All prestored channels
and settings will be deleted in such a case.
" " "
or
3. The TV will reset after a short time and
language selection menu will be displayed.
4. Follow the steps in the Initial set up section.

Clear Service List

(*) This setting is visible only when the Country option
is set to Denmark, Sweden, Norway or Finland.
1. Use this setting to clear channels stored. Press
"
"
button and press
and then press OK.
2. An OSD message will be displayed on the
screen. Press OK to cancel or select Yes to
" " or
delete all of the stored channels.
"
" " " "
or and OK buttons.
NOTE: Analogue Fine Tune feature will not be
" or " " button to select Clear Service List
" or " "
" " " "
or
35