Sony MDS-JE530 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. MiniDisc Player
  5. MDS-JE530 - Md Player
  6. Service manual

Sony MDS-JE530 Service Manual

Mini disc deck
Hide thumbs Also See for MDS-JE530:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
U.S. and foreign patents licensed form Dolby Laboratories
Licensing Corporation.
System
MiniDisc digital audio system
Disc
MiniDisc
Laser
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Laser output
Less than 44.6 µW*
* This output is the value measured
at a distance of 200 mm from the
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Laser diode
Material: GaAlAs
Revolutions (CLV)
400 rpm to 900 rpm
Error correction
Advanced Cross Interleave Reed
Solomon Code (ACIRC)
Sampling frequency
44.1 kHz
Coding
Adaptive Transform Acoustic Coding
(ATRAC)
Modulation system
EFM (Eight-to-Fourteen Modulation)
Number of channels
2 stereo channels
Frequency response
5 to 20,000 Hz ±0.3 dB
Signal-to-noise ratio
Over 98 dB during playback
Wow and flutter
Below measurable limit
Input
LINE (ANALOG) IN
Jack type: phono
Impedance: 47 kilohms
Rated input: 500 mVrms
Minimum input: 125 mVrms
DIGITAL OPTICAL IN
Connector type: square optical
Impedance: 600 nm (optical wave length)
DIGITAL COAXIAL IN
Jack type: phono
Impedance: 75 ohms
Rated input: 0.5 Vp-p, ±20%
MICROFILM
MDS-JE530
Photo: Black model
Model Name Using Similar Mechanism
MD Mechanism Type
Optical Pick-up Type
SPECIFICATIONS
Outputs
PHONES
LINE (ANALOG) OUT
DIGITAL OPTICAL OUT Connector type: square optical
General
Power requirements
North American model:
European model:
Other models:
Power consumption
Dimension (approx.)
Mass (approx.)
Supplied accessories
• Audio connecting cords (2)
• Optical cable (1)
• Remote commander (remote) RM-D29M (1)
• R6 (size-AA) batteries (2)
US Model
Canadian Model
AEP Model
UK Model
E Model
MDS-JE520
MDM-5D
KMS-260B/J1N
Jack type: stereo phone
Rated output: 28 mW
Load impedance: 32 ohms
Jack type: phono
Rated output: 2 Vrms (at 50 kilohms)
Load impedance: Over 10 kilohms
Rated output: –18 dBm
Load impedance: 660 nm (optical
wave length)
120 V AC, 60 Hz
230 V AC, 50/60 Hz
110 – 120 V or 220 – 240 V AC, 50/60 Hz
Adjustable with voltage selector
16 W
430 × 95 × 280 mm (w/h/d) incl.
projecting parts and controls
3.4 kg
MINI DISC DECK

Advertisement

Table of Contents
loading

Related Manuals for Sony MDS-JE530

Summary of Contents for Sony MDS-JE530

  • Page 1 MDS-JE530 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Photo: Black model Model Name Using Similar Mechanism MDS-JE520 U.S. and foreign patents licensed form Dolby Laboratories Licensing Corporation. MD Mechanism Type MDM-5D Optical Pick-up Type KMS-260B/J1N...

  • Page 2: Self-Diagnosis Function

    SELF-DIAGNOSIS FUNCTION The self-diagnosis function consists of error codes for customers which are displayed automatically when errors occur, and error codes which show the error history in the test mode during servicing. For details on how to view error codes for the customer, refer to the following box in the instruction manual.
  • Page 3 Items of Error History Mode Items and Contents Selecting the Test Mode Display Details of History total rec Displays the recording time. Displayed as “rππππππh”. The displayed time is the total time the laser is set to the high power state. This is about 1/4 of the actual recording time.

  • Page 4: Table Of Contents

    SECTION 1 SERVICING NOTES TABLE OF CONTENTS SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: SELF-DIAGNOSIS FUNCTION ........2 Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage.
  • Page 5 OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- NUMÉROS SONT DONNÉS DANS CE MANUEL OU LISHED BY SONY.
  • Page 6 JIG FOR CHECKING BD BOARD WAVEFORM The special jig (J-2501-149-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to be performed are shown as follows. GND : Ground I+3V : For measuring IOP (Check the deterioration of the optical pick-up laser) IOP : For measuring IOP (Check the deterioration of the optical pick-up laser) TEO : TRK error signal (Traverse adjustment) VC : Reference level for checking the signal...
  • Page 7 IOP DATA RECORDING AND DISPLAY WHEN OPTICAL PICK-UP AND NON-VOLATILE MEMORY (IC171 OF BD BOARD) ARE REPLACED The IOP value labeled on the optical pick-up can be recorded in the non-volatile memory. By recording the value, it will eliminate the need to look at the value on the label of the optical pick-up.
  • Page 8 CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent. Details of the procedures are described in “5 Electrical Adjustments”. Criteria for Determination Measure if unsatisfactory: (Unsatisfactory if specified value is not satisfied) Laser power check •...
  • Page 9 RETRY CAUSE DISPLAY MODE • In this test mode, the causes for retry of the unit during recording can be displayed on the fluorescent indicator tube. During playback, the “track mode” for obtaining track information will be set. This is useful for locating the faulty part of the unit. •...
  • Page 10 Reading the Retry Cause Display Higher Bits Lower Bits Hexa- Details Hexadecimal decimal When 0 When 1 b7 b6 b5 b4 b3 b2 b1 b0 Binary Emphasis OFF Emphasis ON Monaural Stereo This is 2-bit display. Normally 01. 01:Normal audio. Others:Invalid Audio (Normal) Invalid Original...

  • Page 11: General

    SECTION 2 This section is extracted from GENERAL instruction manual. LOCATION OF CONTROLS – 11 –...
  • Page 12 – 12 –...

  • Page 13: Disassembly

    SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. CASE (408226) 1 two screws 2 case (408226) (CASE 3 TP2) 1 two screws (CASE 3 TP2) FRONT PANEL SECTION 2 connector (CN791) 4 claw 1 wire (flat type) (19 core) (CN421) 4 claw 3 six screws...
  • Page 14 MAIN BOARD 1 wire (flat type) (21 core) (CN341) 2 power cord connector (CN901) 1 wire (flat type) (23 core) (CN501) 4 four screws (BVTT3 × 6) 1 wire (flat type) (19 core) (CN421) 5 screw (BVTT3 × 6) 7 MAIN board 5 screw (BVTP3 ×...
  • Page 15 SLIDER (CAM) 7 slider (Cam) • Note for Installation of Slider A (Cam) Set the shaft of Cam gear to 3 bracket (Guide L) be at the position in the figure. 1 two screws (P2.6x6) 4 harnes Set the shaft of Lever (O/C) to be at the position in the figure.
  • Page 16 SW BOARD, LOADING MOTOR (M103) 1 screw (PTPWH M2.6 × 6) 2 gear B 3 two screws (PWH1.7 × 4) 4 loading motor (M103) 6 SW board 5 three screws (BTP2.6 × 6) – 16 –...

  • Page 17: Test Mode

    SECTION 4 TEST MODE 1. PRECAUTIONS FOR USE OF TEST MODE • As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc is stopped before setting and removing it. [     EJECT] §...
  • Page 18 5. SELECTING THE TEST MODE [        AMS        ] There are 31 types of test modes as shown below. The groups can be switched by rotating the ≠ ± knob. After selecting the [YES] [        AMS        ] ± group to be used, press the button. After setting a certain group, rotating the ≠...
  • Page 19 5-1. Operating the Continuous Playback Mode 1. Entering the continuous playback mode (1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.) [        AMS        ] ± (2) Turn the ≠ knob and display “CPLAY MODE” (C30). [YES] (3) Press the button to change the display to “CPLAY MID”.
  • Page 20 6. FUNCTIONS OF OTHER BUTTONS Function Contents Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking servo · turns ON/OFF. Stops continuous playback and continuous recording. The sled moves to the outer circumference only when this is pressed. The sled moves to the inner circumference only when this is pressed.
  • Page 21 MEANINGS OF OTHER DISPLAYS Contents Display When Lit When Off During continuous playback (CLV: ON) STOP (CLV: OFF) Tracking servo OFF Tracking servo ON Recording mode ON Recording mode OFF SYNC CLV low speed mode CLV normal mode A.SPACE ABCD adjustment completed OVER Tracking offset cancel ON Tracking offset cancel OFF...

  • Page 22: Electrical Adjustments

    SECTION 5 ELECTRICAL ADJUSTMENTS 1. PARTS REPLACEMENT AND ADJUSTMENT • Check and adjust the MDM and MBU as follows. The procedure changes according to the part replaced • Abbreviation : Optical pick-up OWH : Overwrite head • Temperature compensation offset check •...
  • Page 23 2. PRECAUTIONS FOR CHECKING LASER DIODE 4. Use the following tools and measuring devices. • Check Disc (MD) TDYS-1 EMISSION (Parts No. 4-963-646-01) To check the emission of the laser diode during adjustments, never • TEST DISK (MDW-74/AU-1) (Parts No. 8-892-341-41) view directly from the top as this may lose your eye-sight.
  • Page 24 [YES] 6. CHECK PRIOR TO REPAIRS Note 1: After step 4, each time the button is pressed, the display will be switched between “LD 0.7 mW $ ”, “LD 6.2 mW $ These checks are performed before replacing parts according to ”, and “LD Wp ”.
  • Page 25 [YES] 6-4. Focus Bias Check 9. Press the button display “EFB = MO-P”. Then, the optical pick-up moves to the pit area automatically Change the focus bias and check the focus tolerance amount. and servo is imposed. Checking Procedure : 10.
  • Page 26 7. INITIAL SETTING OF ADJUSTMENT VALUE 9. TEMPERATURE COMPENSATION OFFSET ADJUSTMENT Note: Save the temperature data at that time in the non-volatile memory Mode which sets the adjustment results recorded in the non-volatile as 25 ˚C reference data. memory to the initial setting value. However the results of the tempera- Note : ture compensation offset adjustment will not change to the initial setting 1.

  • Page 27: Traverse Adjustment

    [        AMS        ] ± 7. Then, turn the ≠ knob and display “LDPWR 11. TRAVERSE ADJUSTMENT CHECK” (C02). [YES] Note 1: Data will be erased during MO reading if a recorded disc is 8. Press the button once and display “LD 0.9 mW $ ”.
  • Page 28 [        AMS        ] [YES] ≠ ± 8. Turn the knob so that the waveform of the 18. Press the button, display “EFB = SAV” for a mo- oscilloscope becomes the specified value. ment and save the adjustment results in the non-volatile [        AMS        ] (When the ≠...
  • Page 29 13.ERROR RATE CHECK 15. AUTO GAIN CONTROL OUTPUT LEVEL 13-1. CD Error Rate Check ADJUSTMENT Checking Procedure : Be sure to perform this adjustment when the pickup is replaced. 1. Load the check disc (MD) TDYS-1. If the adjustment results becomes “Adjust NG!”, the pickup may [        AMS        ] ±...
  • Page 30 Adjustment Location: – BD BOARD (Side A) – CN101 D101 CN110 I+3V NOTE IC171 – BD BOARD (Side B) – IC101 IC121 IC192 Note: It is useful to use the jig. for checking the waveform. (Refer to Servicing Notes on page 6) –...

  • Page 31: Diagrams

    MDS-JE530 SECTION 6 DIAGRAMS ADDT 6-1. BLOCK DIAGRAM – MD SERVO Section – DIGITAL SIGNAL PROCESSOR, (Page 33) EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, IC121 (1/2) ATRAC ENCODER/DECODER IC611 OVER WRITE IC121 (1/2) IC611 EFMO ADDT OPTICAL HEAD DRIVE DIGITAL IN...

  • Page 32: Block Diagram - Main Section

    MDS-JE530 6-2. BLOCK DIAGRAM – MAIN Section – A/D, D/A CONVERTER IC321 • SIGNAL PATH : PLAY (ANALOG OUT) J101 : REC (ANALOG IN) AINL HIGH-PASS FILTER, ADDT SDTO SUB- LINE AMP LINE (ANALOG) DIGITAL CONVERTER AINR TRACKTION IC301 ATTENUATOR...

  • Page 33: Note For Printed Wiring Boards And Schematic Diagrams

    6-3. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. pF: µµF • Y : parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics •...
  • Page 34 • Circuit Boards Location BD board SW board MAIN board POWER SW board HP board DISPLAY board KEY SW board – 36 –...

  • Page 35: Printed Wiring Board - Bd Board

    MDS-JE530 6-4. PRINTED WIRING BOARD – BD Board – • See page 36 for Circuit Boards Location. S102 REFLECT DET, PROTECT DET LOW REFLECT RATE/ UNPROTECT (SLIDE) HIGH REFLECT RATE/ WRITE PROTECT (SPINDLE) (Page 45) (Page 45) • Semiconductor • Semiconductor...

  • Page 36: Schematic Diagram - Bd Board (1/2)

    MDS-JE530 6-5. SCHEMATIC DIAGRAM – BD Board (1/2) – • See page 43 for Waveforms. • See page 55 for IC Block Diagrams. (Page 41) (Page 41) (Page 41) (Page 42) (Page 42) (Page 42) (Page 42) – 39 –...

  • Page 37: Schematic Diagram - Bd Board (2/2)

    MDS-JE530 6-6. SCHEMATIC DIAGRAM – BD Board (2/2) – • See page 43 for Waveforms. • See page 55 for IC Block Diagrams. (Page 40) (Page 40) (Page 39) (Page 39) (Page 39) (Page 40) (Page 40) (Page 48) (Page 47) •...

  • Page 38: Schematic Diagram - Sw Board

    MDS-JE530 • Waveforms – BD Board – 6-7. SCHEMATIC DIAGRAM – SW Board – 1 IC101 1, 2 (I, J) (Play mode) 6 IC121 @• (XBCK) 3 IC321 9 (XTI) 3.8 Vp-p 5.4 Vp-p 0.46 Vp-p 45.1584 MHz 2.8224 MHz 2 IC101 4 (A) (Play mode) 7 IC121 @ª...

  • Page 39: Printed Wiring Board - Main Board

    MDS-JE530 (Page 44) 6-9. PRINTED WIRING BOARD – MAIN Board – • See page 36 for Circuit Boards Location. • Semiconductor Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location D341 E-13 D421...

  • Page 40: Schematic Diagram – Main Board (1/2)

    MDS-JE530 6-10. SCHEMATIC DIAGRAM – MAIN Board (1/2) – • See page 43 for Waveforms. (Page 49) (Page (Page 54) (Page 49) (Page 41) (Page 44) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : PLAY –...

  • Page 41: Schematic Diagram - Main Board (1/2)

    MDS-JE530 6-11. SCHEMATIC DIAGRAM – MAIN Board (2/2) – • • See page 43 for Waveforms. See page 57 for IC Block Diagrams. (Page 48) (Page 54) (Page • Voltages and waveforms are dc with respect to ground under no-signal conditions.

  • Page 42: Printed Wiring Boards - Panel Section

    MDS-JE530 6-12. PRINTED WIRING BOARDS – PANEL Section – • See page 36 for Circuit Boards Location. • Semiconductor Location Ref. No. Location IC761 IC771 Q781 Q782 (Page 45) (Page 46) – 51 – – 52 –...

  • Page 43: Schematic Diagram - Panel Section

    MDS-JE530 6-13. SCHEMATIC DIAGRAM – PANEL Section – • See page 43 for Waveform. (Page (Page 50) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : STOP – 53 – – 54 –...
  • Page 44 • IC Block Diagrams IC121 CXD2656R – BD Board – IC101 CXA2523AR 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 SPINDLE GENERATOR SERVO 43 42 75 TE MNT0...

  • Page 45: Main Board

    – MAIN Board – IC310 M5293L IC431 LA5632 – REFERENCE STBY VOLTAGE ANA5 – REFERENCE ON/OFF – VOLTAGE SYS3.3 – OVERHEAT OVERCURRENT PROTECTION LIMITTER – 3.3V B.BAK – DELAY P. DOWN CIRCUIT IC321 AK4524 – VCOM DELAY S. RESET CIRCUIT VREF AINR AOUTR+...

  • Page 46: Ic Pin Function Description

    6-14. IC PIN FUNCTION DESCRIPTION • BD BOARD IC101 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP) Pin No. Pin Name Description I-V converted RF signal I input from the optical pick-up block detector I-V converted RF signal J input from the optical pick-up block detector Middle point voltage (+1.65V) generation output terminal 4 to 9 A to F...
  • Page 47 • BD BOARD IC121 CXD2656R (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER) Pin No. Pin Name Description Focus OK signal output to the system controller (IC501) MNT0 (FOK) “H” is output when focus is on (“L”: NG) MNT1 (SHOCK) Track jump detection signal output to the system controller (IC501) MNT2 (XBUSY)
  • Page 48 Pin No. Pin Name Description Address signal output to the D-RAM (IC124) XRAS Row address strobe signal output to the D-RAM (IC124) “L” active Write enable signal output to the D-RAM (IC124) “L” active Two-way data bus with the D-RAM (IC124) I (S) MVCI Digital in PLL oscillation input from the external VCO Not used (fixed at “L”)
  • Page 49 Pin No. Pin Name Description Clock signal (176.4 kHz) output terminal (X’tal system) Not used (open) SRDR Sled servo drive PWM signal (–) output to the BH6511FS (IC152) SFDR Sled servo drive PWM signal (+) output to the BH6511FS (IC152) SPRD Spindle servo drive PWM signal (–) output to the BH6511FS (IC152) SPFD...
  • Page 50 • MAIN BOARD IC501 M30624MG-207FP (SYSTEM CONTROLLER) Pin No. Pin Name Description 1, 2 Not used (open) Monitor output terminal for the test C1 error rate is output when test mode ADER Monitor output terminal for the test ADER is output when test mode Subcode Q sync (SCOR) input from the CXD2656R (IC121) SQSY “L”...
  • Page 51 Pin No. Pin Name Description DA RST Reset signal output to the A/D, D/A converter (IC321) “L”: reset MUTE Audio line muting on/off control signal output terminal “L”: line muting on Strobe signal output to the power supply circuit “L”: standby mode, “H”: power on Detection input from the disc chucking-in detect switch “L”: chucking CHACK IN...
  • Page 52 Pin No. Pin Name Description Focus OK signal input from the CXD2656R (IC121) MNT0 (FOK) “H” is input when focus is on (“L”: NG) Clock signal output to the EEPROM (IC171) Recording data output enable signal output to the CXD2656R (IC121) and overwrite head SCTX driver (IC181) Writing data transmission timing output (Also serves as the magnetic head on/off output)

  • Page 53: Exploded Views

    SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark may have some difference from the original are seldom required for routine service.
  • Page 54 (2) FRONT PANEL SECTION supplied with J791 not supplied supplied with RV791 AEP, UK, SP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-996-691-12 WINDOW (FL) 4-951-620-01 SCREW (2.6X8), +BVTP A-4672-565-A KNOB (AMS) ASSY (BLACK) 1-673-242-11 HP BOARD 4-996-687-61 KNOB (AMS) (SILVER) 3-917-216-11 KNOB (TIMER) (BLACK) 3-354-981-01 SPRING (SUS), RING (for SILVER)
  • Page 55 (3) MECHANISM SECTION (MDM-5D) not supplied M103 MBU-5D Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 201 1-668-111-11 SW BOARD 4-996-227-01 LEVER (HEAD) * 202 4-996-217-01 CHASSIS 4-996-229-01 SPRING (HEAD LEVER), TORSION 4-996-223-01 INSULATOR (F) (BLACK) 4-996-212-01 LEVER (LIMITTER) * 204 4-996-218-01 BRACKET (GUIDE R)
  • Page 56 (4) BASE UNIT SECTION (MBU-5D) HR901 not supplied not supplied M101 S102 not supplied M102 The components identified by Les composants identifiés par une mark ! or dotted line with marque ! sont critiques pour la mark ! are critical for safety. sécurité.

  • Page 57: Electrical Parts List

    SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark are seldom required for routine service. parts list may be different from the parts speci- ! are critical for safety.
  • Page 58 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL/SHORT > R145 1-216-073-00 METAL CHIP 1/10W R146 1-216-037-00 METAL CHIP 1/10W L101 1-414-813-11 FERRITE R147 1-216-025-00 RES, CHIP 1/10W L102 1-414-813-11 FERRITE R148 1-216-045-00 METAL CHIP 1/10W L103 1-414-813-11 FERRITE...
  • Page 59 DISPLAY KEY SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C774 1-162-294-31 CERAMIC 0.001uF 1-673-242-11 HP BOARD C775 1-162-294-31 CERAMIC 0.001uF ********* C776 1-162-294-31 CERAMIC 0.001uF C781 1-162-294-31 CERAMIC 0.001uF < CAPACITOR > C782 1-164-159-11 CERAMIC 0.1uF C791 1-162-282-31 CERAMIC...
  • Page 60 KEY SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S706 1-762-875-21 SWITCH, KEYBOARD (·) C356 1-126-933-11 ELECT 100uF S711 1-762-875-21 SWITCH, KEYBOARD (MENU/NO) S712 1-762-875-21 SWITCH, KEYBOARD (YES) C357 1-164-159-11 CERAMIC 0.1uF S713 1-475-543-11 ENCODER, ROTARY C358 1-164-159-11 CERAMIC 0.1uF...
  • Page 61 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C612 1-162-306-11 CERAMIC 0.01uF < IC > C621 1-164-159-11 CERAMIC 0.1uF (US, CND, SP) IC101 8-759-634-50 IC M5218AL C622 1-162-306-11 CERAMIC 0.01uF IC201 8-759-634-50 IC M5218AL (US, CND, SP) IC301 8-759-634-50 IC M5218AL C623...
  • Page 62 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-249-429-11 CARBON 1/4W (AEP, UK) R421 1-249-385-11 CARBON 1/6W 1-249-429-11 CARBON 1/4W R422 1-249-433-11 CARBON 1/4W R424 1-249-441-11 CARBON 100K 1/4W 1-249-429-11 CARBON 1/4W R425 1-249-441-11 CARBON 100K 1/4W 1-249-429-11 CARBON...
  • Page 63 MAIN POWER SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R624 1-249-437-11 CARBON 1/4W < SWITCH > R631 1-247-804-11 CARBON 1/4W (AEP, UK) S601 1-572-126-21 SWITCH, PUSH (1 KEY) (REC POSITION) R632 1-249-417-11 CARBON 1/4W S602 1-572-126-21 SWITCH, PUSH (1 KEY) (PACK OUT) (AEP, UK)
  • Page 64 MDS-JE530 Sony Corporation 99C0586-1 Printed in Japan © 1999. 3 9-928-824-11 Home A&V Products Company Published by Quality Assurance Dept. – 76 – (Shinagawa)

Table of Contents