Download Print this page

VisAccess CL-83 Installation Manual

Advertisement

Quick Links

CL-83, CL-83M
Anti-Vandal, Access Control Keypad
1. INTRODUCTION
1.1 Description
The CL-83 is a digital programmable access control keypad. The
CL-83M is a similar keypad - mullion type. Each system includes
an outdoor, rugged, vandal resistant keypad and an indoor
sophisticated microprocessor-controlled keypad, as shown in
figure 1.
Power
supply
12/24V
DC/AC
Indoor Keypad
and Control Unit
(CL-8A EXT)
Figure 1 - Using CL-83/CL-83M as an Access Control System
The system users have 56 individual, preprogrammed digital
codes (each code includes 1-8 digits), that they must key on the
outdoor / indoor keypads, to unlock electrically controlled doors or
barriers. More than 100 million code combinations are possible. A
penalty timer locks out the keypads for 30 seconds after entering
three consecutive erroneous codes. User codes may be
individually deleted.
The system has programmable AUXILIARY open-collector output
with seven powerful operating modes. Each user code can be
programmed to operate the internal RELAY, the AUXILIARY
output, or BOTH.
An AMBUSH digit, if entered after the last digit of the user code,
causes a one-second pulse of the PANIC output, used to send a
message to the security personnel if the user is forced to disarm
the system under violence or menace.
2. SPECIFICATIONS
Indoor Keypad and Control Unit (CL-8A EXT)
Code composition: 1 to 8 digits, any combination
Keypad type: 12 keys, 3 X 4, tactile operation
Operating voltage: 9-16 or 22-26 V AC/DC, selected with
jumper
Current drain: 15 mA in the standby state, 55 mA with relay and
AUXILIARY output active.
Power failure immunity: EEPROM retains all programmed
information even during total power loss.
Other protections: Watch-dog protection from processor hang-up.
Relay contact rating: 10A /30V AC or DC
Relay control: Programmable for 1 – 98 seconds pull-in duration,
or for toggle (latching/unlatching) mode.
AUX and PANIC output current sinking: Up to 100 mA (each
protected by an 18 ohm series resistor).
LEDs: Green indicates keypad status
Red and yellow have 1K ohm series resistors and
terminals for external connections
Operating temperature range: -20°C to 65°C (-4°F to 149°F)
Size: (H x W x D): 118 x 72 x 33 mm (4-5/8 x 2-3/16 x 1-3/8 in.)
Weight: 122 g (4.3 oz)
Color: White
Compliance with Standards: CE
Page 1 of 6
DE6218-3
Outdoor Keypad
(CL-83)
Outdoor Keypad
(CL-83M)
Installation Guide
1.2 Indoor Keypad & Control Unit Features
Functions as the "brain" of the access control system.
Includes 12 push-buttons, 3 LEDs and buzzer.
Designed to accept data from both its own keys and from
the outdoor keypad.
Suitable for flush and surface mounting (supplied with a
surface mounting box).
Includes a 10A relay that activates the door strike or
performs any desired switching function.
Programmable on site by use of its own keyboard.
Non-volatile EEPROM stores programmed data, unaffected
by power failure.
Programmable relay contact closure duration; toggle (latch/
unlatch) mode may be selected if required.
PANIC output is triggered by pressing the
simultaneously, on the indoor or outdoor keypad.
REQUEST TO EXIT remote input trips the relay with a
remote switch or a detector.
Tamper switch option available.
1.3 Outdoor Keypad Features
Rugged, water and vandal resistant keypad.
Includes 12 push-buttons and 2 LEDs.
Any of the functions that can be performed by using the
indoor keypad push-buttons can also be done by the
outdoor keypad push-buttons.
Tamper protected.
Suitable for surface mounting.
Power is received from the indoor keypad.
Environmental Protection: IP68
Outdoor Keypads (CL-83, CL-83M)
Housing Material: Aluminum 6061 T6
Number of Keys: 12 (CL-83: 3 x 4 matrix, CL-83M: 2 X 6 matrix)
Number of LEDs: 1 green, 1 red
Operating Voltage: Supplied from CL-8A EXT keypad
Operating & Storage Temps: -20°C to 65°C (-4°F to 149°F)
Dimensions (H x W x D):
CL-83: 130 x 81 x 19mm (5-1/8 x 3-3/32 x 3/4in.)
CL-83M: 180 x 44 x 21mm (7-1/8 x 1-3/4 x 27/32 in.)
Weight: CL-83: 290g (10 oz)
Color: Metallic gray (anodized aluminum)
Compliance with Standards: CE
Environmental Protection: Waterproof and dustproof (IP68)
#
and
*
CL-83M: 310g (10.9 oz)
keys

Advertisement

loading

Summary of Contents for VisAccess CL-83

  • Page 1 Housing Material: Aluminum 6061 T6 Code composition: 1 to 8 digits, any combination Number of Keys: 12 (CL-83: 3 x 4 matrix, CL-83M: 2 X 6 matrix) Keypad type: 12 keys, 3 X 4, tactile operation Number of LEDs: 1 green, 1 red...
  • Page 2: Installation

    # 22 AWG or larger. Route the wires through the wiring knockouts on the back box. Two cables (1 meter long) are supplied with the CL-83 / CL-83M, P/N PAW 80011, 6x6005/AWG#22. 3.4 Wiring...
  • Page 3: Operation

    3.6 Outdoor Keypads Tamper Option F. Connect the remote request-to-exit switch or PIR contacts To use the CL-83 / CL-83M Tamper switch: Connect the 2 tamper across terminals 5 and 6 of the indoor keypad. To light the terminals (see figure 6) to the tamper N.C. terminals of the alarm CL8A EXT’s red LED: Connect the 12 or 24Volt power supply...
  • Page 4 The green LED lights steadily for 2 seconds and then flashes All code allocations should be recorded, and a User Code Programming Chart - Appendix A, is supplied for this purpose. slowly, indicating that the data has been saved and that you are back in the programming menu.
  • Page 5: Appendix A: User Codes List

    6. RESETTING THE DEFAULT MASTER CODE you forget or misplace the master code (code No. 01) and it two seconds and after that will start flashing slowly, indicating becomes necessary to reprogram the keypad, you will have to that the programming menu is active. reset the master code to the factory default ( 1234 ) as follows: Important Note: The master code has temporarily A.
  • Page 6: Warranty

    Function Keying Format Format Explanation and Correct Response • After pressing [1] - rapid flashing; Programming user [1] [NN] # [C]# [C]# [F] # [NN] = The serial number of the code user, 01 to 56 codes (prepare a • After keying [NN]# - steady light for 2 seconds and then rapid flashing.

This manual is also suitable for:

Cl-83m