Operating Instructions
RB Tube Cutter
Model N30P
For Coated and Nude Copper Pipes
For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.
Use the cutter only for the types of tubes described in these
・
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.
Always inspect the cutter before use. If you find anything wrong,
・
do not use until repairs have been made.
When cutting pipes, make sure the blade doesn't touch your hand.
・
Never place your fingers between the blade and the pipe.
Avoid dropping the cutter either when using or carrying it.
・
Be sure to remove any water or flux from the cutter. Failure to do
・
so could result in the bearings becoming rusty and malfunctioning.
Instructions
Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again
1 /4
of a turn.
Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.
Then turn the grip slowly, (
1 /8
of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.
Avoid cutting too quickly or the pipe may
・
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
・
you can also cut copper (annealed or
unannealed) and brass pipes.
Specifications
Application
Coated and Nude Copper Pipes
Cutting capacity
External Diam. 5 - 34 mm
Weight (main unit)
350g
Blade diameter
φ32
Rollers
625ZZ
Spare Blade Code No.
424237
Optional Extras
Blade for Thin wall Stainless Steel Pipes
(Code No.424233, 424284)
1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan
Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878
www.rexind.co.jp
Code No.
427830
Blade
Rollers
Turn
①
Pipe
Grip
Fig.1
Rotate
Fig.2
Turn grip approx.1/8 of 3 or 4 turn
Fig.3
Rotate cutter once
4V440-E2
1304D01000
Operating Instructions
RB Tube Cutter
Model N30S
For Thin wall Stainless Steel Pipes
For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.
Use the cutter only for the types of tubes described in these
・
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.
Always inspect the cutter before use. If you find anything wrong,
・
do not use until repairs have been made.
When cutting pipes, make sure the blade doesn't touch your hand.
・
Never place your fingers between the blade and the pipe.
Avoid dropping the cutter either when using or carrying it.
・
Be sure to remove any water or flux from the cutter. Failure to do
・
so could result in the bearings becoming rusty and malfunctioning.
Instructions
Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again
1 /4
of a turn.
Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.
Then turn the grip slowly, (
1 /8
of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.
Avoid cutting too quickly or the pipe may
・
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
・
you can also cut copper (annealed or
unannealed) and brass pipes.
Specifications
Application
Thin wall Stainless Steel Pipes
Cutting capacity
External Diam. 5 - 34 mm
Weight (main unit)
350g
Blade diameter
φ30
Rollers
625ZZ
Spare Blade Code No.
424233, 424284
Optional Extras
Blade for Coated and Nude Copper pipes
(Code No. 424237)
1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan
Tel. +81-(0)72-961-9820 Fax +81-(0)72-961-9878
www.rexind.co.jp
Code No.
427630
Blade
Rollers
Turn
①
Pipe
Grip
Fig.1
Rotate
Fig.2
Turn grip approx.1/8 of 3 or 4 turn
Fig.3
Rotate cutter once
4V410-E1
0808D01000