Page 2
Notice This manual and any examples contained herein are provided “as is” and are subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Page 3
If your computer was shipped with a product Recovery CD-ROM: (i) The product recovery CD-ROM and/or support utility software may only be used for restoring the hard disk of the HP computer with which the product recovery CD-ROM was originally provided. (ii) The use of any operating system...
Page 4
software by Microsoft contained in any such product recovery CD-ROM shall be governed by the Microsoft End User License Agreement (EULA). Customer may transfer rights in the software to a third party only as part of the transfer of all rights and only if Customer obtains the prior agreement of the third party to be bound by the terms of this License Agreement.
Contents 1. Introducing the OmniBook ....... Taking Inventory ........Included in the OmniBook 7100 box ....... To buy OmniBook accessories ......OmniBook features ........Setting Up Windows ........To set up the OmniBook ....... Configuring the OmniBook with the BIOS Setup Utility.....
Page 6
To set or change a password......2-20 To delete a password........2-21 To install McAfee VirusScan ......2-21 To attach a security cable....... 2-22 To set PC identification ........ 2-23 To enable hard disk drive lock ......2-23 3. Managing Battery Power......... Monitoring Battery Power.........
Page 7
5. Expanding the OmniBook ........ Installing a Hard Disk Drive ....... To replace the hard disk drive......To replace the hard disk drive holder ...... To create a Hibernate partition ......Installing a RAM Expansion Module ......To install a RAM expansion module ....... To remove a RAM expansion module ......
Page 8
Startup Problems........7-14 Testing the Operation ........7-15 To create a diagnostic floppy disk ......7-15 To run the diagnostic test ....... 7-16 8. Specifications and Regulatory Information ....Hardware Specifications ......... Software System Resources........ Safety Information........Regulatory Information ........8-10 U.S.A.
Corporate Evaluator’s Guide The provides information about installing alternate operating systems, as well as how to configure the OmniBook in a corporate, networked environment. Located at the OmniBook website. HP Support Assist CD-ROM See the Support and Service booklet for telephone numbers.
Introducing the OmniBook Taking Inventory The HP OmniBook 7100 represents a new category of HP notebook computers featuring the latest mobile technologies available. It uses a high-speed Intel Pentium II processor with MMX technology, a large TFT display, and a high-capacity hard drive.
Buy OmniBook accessories online! For the latest accessories and options, visit us at . As new accessories become available, you’ll find them listed here. At the time of this printing, HP offers a variety of docking solutions, plug-in modules, and other accessories, including the following: Docking system and monitor stand (HP F1477A).
Introducing the OmniBook OmniBook features OmniBook—Front View 1. Built-in microphone. 2. Status panel. 3. Blue power button (suspends or shuts down the OmniBook). 4. Pointing stick (pointing device). 5. Touch pad (pointing device). 6. Built-in speakers. 7. Plug-in module bay (can contain a CD-ROM / floppy disk drive, LS-120 drive, DVD drive, or a second battery).
Page 14
Introducing the OmniBook 10. System-off button (to shut down the OmniBook). 11. Kensington lock slot. 12. Latch to open and close the OmniBook. OmniBook—Side View 13. AC adapter jack. 14. PC Card slots (upper and lower). Accepts PC Card Types II or III (PCMCIA and CardBus).
Page 15
22. External monitor port. 23. S-video (TV-out) port. 24. Docking port (for HP OmniBook docking products). 25. Universal serial bus port (USB). Windows NT 4.0 does not support USB. 26. PS/2 keyboard or PS/2 mouse port (supports a standard Y adapter).
Introducing the OmniBook Setting Up Windows The OmniBook has either Windows 95 or Windows NT 4.0 factory-installed on the hard disk drive. When your OmniBook starts up the first time, it takes you through a series of setup screens, including installation of the operating system. This section describes how to set up the OmniBook with the factory-installed Windows operating system.
Introducing the OmniBook To set up the OmniBook 1. Install the OmniBook’s battery. (See the Quick Start sheet or page 3-7 of this manual). 2. Connect the power cord to the ac adapter, then plug the cord into an ac outlet. The indicator light on the ac adapter shines when the adapter is powered.
1. Close all applications, then shut down Windows and restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. The pointing devices are not active in the BIOS Setup utility. Press the RIGHT and LEFT arrow keys to move among menus.
Page 19
Introducing the OmniBook Main Menu Default Language Sets the language for this utility and for BIOS Same as operating messages. system. BIOS Revision Shows the current BIOS version. Detected automatically. System Time Sets the time using 24-hour format. Values set take effect immediately. System Date Sets the date using dd/mm/yy format (except English, which is mm/dd/yy format).
Page 20
Introducing the OmniBook System Devices Menu Default Internal Pointing Devices Enables one or both built-in PS/2 devices. Both External Fn Key Sets whether left-CTRL + left-ALT on an Enabled external keyboard is interpreted as the Fn key. IDE Controller Enables the primary (hard drive) and secondary Both (optional CD-ROM drive) controllers.
Introducing the OmniBook Interrupt Sets the interrupt. IRQ5 1st DMA channel Sets the DMA channel for playback. DMA1 2nd DMA channel Sets the DMA channel for recording. DMA0 MPU Device Sets how the MIDI capability (hardware Disabled wavetable) is configured by the BIOS (specified or automatic).
Introducing the OmniBook Power Menu Default Power Management Mode Disables time-outs, selects a combination of Max Power time-outs, or allows customized time-outs. Savings Smart CPU Mode Enables automatic CPU power savings. Absence of keyboard, mouse, and hard disk activity could cause slower CPU response.
Introducing the OmniBook Boot Menu Default Diskette Drive Shows the order of boot devices. Move the 1. Diskette drive Hard Drive entries to change the order. 2. Hard drive CD-ROM Drive 3. CD-ROM drive Exit Menu Save Changes and Exit Saves Setup changes, exits, and reboots.
To run TopTools locally, click Start, Programs, HP DMI, HP TopTools. To get more information about TopTools For information on manageable HP PCs, HP TopTools, DMI, and how they lower PC operating costs, see the see the HP website at http://www.hp.com/toptools.
Operating the OmniBook This chapter introduces the OmniBook and helps you get familiar with basic operation, including Starting and stopping the OmniBook. Using the OmniBook pointing devices. Managing pointing devices. Using the OmniBook display. Adjusting the audio system. Using the OmniBook keyboard. Checking the status of the OmniBook.
Operating the OmniBook Starting and Stopping the OmniBook You can easily start and stop your OmniBook using the blue power button. However, at certain times, you may want to use other methods for starting and stopping your OmniBook—depending on power considerations, types of active connections, and start-up time.
Operating the OmniBook To reset the OmniBook If Windows or the OmniBook stops responding, you can reset the OmniBook and restart Windows. 1. If possible, shut down Windows. 2. Press and hold the blue power button until the display shuts down. –or, if this fails–...
Operating the OmniBook Using the OmniBook Pointing Devices Two pointing devices (pointing stick and touch pad) are built into your OmniBook. The default pointing device driver (PS/2 TrackPoint), supports the enhanced features of the pointing stick and basic features of the touch pad. You can customize the OmniBook to support enhanced touch pad features.
Operating the OmniBook To use the built-in pointing devices 1. Place your hands in the typing position. With your index finger, press the pointing stick in the direction you want the pointer to move. Pressing away from you moves the pointer up the screen;...
2. Disable the pointing stick 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the System Devices menu. 4. Highlight Internal Pointing Devices and select Touch Pad.
2. Enable the pointing stick 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the System Devices menu. 4. Highlight Internal Pointing Devices and select Pointing Stick. (Choose Both if you want basic touch pad features available.)
Operating the OmniBook To configure pointing devices To customize the operation of all pointing devices (pointing stick, touch pad, and external PS/2 or serial mouse), in Control Panel open Mouse. You can change left and right button actions, double-click speed, pointer speed and tail, and more.
Operating the OmniBook Using the OmniBook Display This section describes How to adjust the display brightness. How to extend the life of the display. To adjust the display brightness The OmniBook uses special key combinations, called hot keys, to control brightness. Press Fn+F1 to decrease the brightness.
Operating the OmniBook Adjusting the Audio System The OmniBook supports Sound Blaster Pro-compatible sound and the Microsoft Windows Sound System. This section describes How to adjust the volume manually. How to adjust the volume in Windows. To adjust the volume manually To increase the volume, press Fn+UP-ARROW.
Operating the OmniBook Using the OmniBook Keyboard This section describes the OmniBook’s keyboard features, including how to Use the Fn hot keys. Use the Windows keys. Use the embedded keypad. Use the ALT GR key on a non-US keyboard. 2-12...
Operating the OmniBook To use the Fn hot keys The combination of the Fn key plus another key creates a hot key—a shortcut key sequence—for various system controls. The OmniBook keyboard shows the Fn hot keys labeled in gray. Pressing these keys Does this Fn + F1 Decreases the display’s brightness.
Operating the OmniBook To use the Windows keys There are two Windows keys on the keyboard. The one next to the Fn key brings up the Windows Start menu. The one at the top center of the keyboard brings up the shortcut menu for the current application.
Operating the OmniBook To use the ALT GR key Non-U.S. keyboards have an ALT GR key to the right of the spacebar. This is a shift key providing access to certain keyboard characters. For a character in the lower-right corner of a key, press and hold ALT GR to type the character.
Operating the OmniBook Checking the Status of the OmniBook This section describes how to interpret the status lights and the status panel indicators. To interpret the status lights The OmniBook has status lights that report power status and drive activity. When the CD-ROM / floppy disk drive is installed in the module bay, the following lights are present on the front of the OmniBook.
Operating the OmniBook To interpret the status panel indicators The OmniBook status panel, located above the keyboard, contains indicators that show the current power status, drive status, and keyboard status. Power Status Icons AC power. The ac adapter is connected. Battery status.
Page 42
Operating the OmniBook Drive Status Icons Indicator Meaning Drive activity. The OmniBook is accessing either the hard disk drive or any of the following drives in the module bay: CD-ROM drive, DVD drive, or LS-120 drive. Floppy disk drive. The OmniBook is accessing the floppy disk drive.
Operating the OmniBook Protecting the OmniBook Your OmniBook provides several ways for you to identify and protect your computer. This section describes how to Set or change a password. Delete a password. Install McAfee VirusScan. Attach a security cable. Set unique PC identification. Enable drive lock protection.
1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the Security menu. 4. Select Set Administrator Password, then press ENTER.
1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the Security menu. 4. Select Set Administrator Password, then press ENTER.
Operating the OmniBook To attach a security cable Your OmniBook has a built-in connector that allows you to secure the OmniBook with a cable. The Kensington MicroSaver lock system works with this connector and is available at many computer stores. 1.
Hard disk drive lock helps you keep your information secure. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Security menu, enable Password Required To Boot.
Managing Battery Power The OmniBook conserves power by using Advanced Power Management (APM), software that controls battery charging and power drain. , APM is preinstalled on the OmniBook. , you’ll need to install APM (see page 6-17 for instructions). The OmniBook provides several safeguards so you won’t be surprised by a dead-battery condition, including the following: The battery status indicator shows the remaining battery charge.
Managing Battery Power Monitoring Battery Power The primary source of power for the OmniBook is its rechargeable battery pack. You can use the ac adapter to recharge the battery—or to run on ac power to preserve the battery. You can also install a second battery in the plug-in module bay for increased battery time.
Managing Battery Power To check the battery status From the Status Panel Shows the approximate charge level of the battery relative to a full charge. Each bar (displayed from right to left), represents a 10% Full battery charge. The upper and lower triangles indicate the presence of main (upper) and second (lower) batteries.
Managing Battery Power To respond to a low-battery warning When battery power is critically low, you are alerted by one or more of the following: The battery indicator in the status panel appears empty. The computer emits a warning beep. This reminds you to save your work. If the OmniBook has been off, you will not be able to turn it on.
Page 54
Managing Battery Power Charging time Charging the battery takes about 2 hours to fully charge. Battery life With a full charge, battery life in Suspend mode is about 48 hours. If the computer is in use, typical battery life can last up to 3 to 3.5 hours, depending on your level of use and your power management settings (see page 1-14).
Managing Battery Power To replace the main battery If you have any unsaved data, it (and your current work session) will be lost when you remove the battery unless the computer is connected to ac power or a second battery is installed. .
Managing Battery Power To install a second battery The OmniBook’s plug-in module bay accepts a second battery. See page 4-4 for more information about plug-in modules. When a second battery is installed, the lower triangle appears next to the battery icon in the status panel.
Managing Battery Power Conserving Battery Power The OmniBook uses Advanced Power Management (APM) to conserve battery power. You can take steps to optimize your battery operating time. This section describes how to Save battery power. Set time-outs. Get the most from your battery. To save battery power Follow these suggestions to conserve battery power.
1. From the Start menu, shut down then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. Active keys are described along the bottom of the screen. (The touch pad does not work in Setup.) Help information for the highlighted item appears in the right-hand...
Managing Battery Power To get the most from your battery The following are some further suggestions for the best management of your OmniBook batteries. Do not leave batteries unused for long periods of time. If you have more than one, rotate them. If you normally use ac power, make a practice of at least once a week using the battery as your power source.
Making Connections This chapter describes procedures to expand the capabilities of your OmniBook, including Using OmniBook plug-in modules. Connecting external devices. Using PC Cards. Using docking products.
Making Connections Using OmniBook Plug-In Modules The plug-in module bay can hold a CD-ROM / floppy disk drive, an LS-120 drive, a DVD drive, or a second battery. This documentation describes the module that shipped with the OmniBook—the CD-ROM / floppy disk drive. If you’ve purchased other accessory modules, refer to the accessory documentation that accompanied them for instructions.
Making Connections To replace a plug-in module If you are inserting or removing a CD-ROM / floppy disk drive, LS-120 drive, or DVD drive, shut down the OmniBook. 1. From the Start menu, shut down the OmniBook. (This is not necessary if you are removing a battery from the plug-in module bay and inserting another battery.) 2.
Making Connections To insert or eject a floppy disk 1. Hold the disk with its face up, then slide it into the floppy disk drive slot until it clicks into place. 2. To remove the floppy disk, press the eject button on the front of the drive.
Making Connections To insert or remove a CD 1. Press the button on the face of the CD-ROM drive. If one is present, be sure to remove the cardboard packing insert. 2. Place the CD into the drive (label facing up) and gently press down to seat the CD on the spindle–or–remove the CD.
Making Connections Connecting External Devices You can expand the OmniBook’s capabilities by connecting other devices. Before you connect any device, check the documentation that came with the equipment to see if you need to make any settings or adjustments to the equipment before using it.
5. Docking port. 6. Universal serial bus port (USB). 7. PS/2 keyboard or PS/2 mouse port (supports the HP F1469A Y adapter). 8. Back infrared port. There is a second infrared port on the front of the OmniBook. Use this port for wireless data transmission between the OmniBook and another computer or a printer with an infrared port.
1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Main menu, use the down arrow to highlight Video Display Device.
Making Connections To connect a parallel device The parallel port uses a standard 25-pin connector, most commonly used for connecting a printers. These include dot-matrix, ink-jet, and laser printers. The parallel port supports both EPP and ECP capabilities (if selected in BIOS Setup). The OmniBook has one parallel port.
USB devices—this is called a “daisy-chain” connection. If you have problems making this connection, contact the vendor of the peripheral device, as well as the HP website, for the latest versions of the USB drivers. The USB technology is dynamic and continues to develop.
NTSC to PAL. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Main menu, select Television Type, then select PAL.
Page 73
Making Connections Attach the audio cable to the corresponding audio port. When you plug a device into the microphone-in port, the built-in microphone automatically turns off. When you plug a device into the speaker-out port, the built-in speakers automatically turn off. 4-13...
Making Connections To make an infrared connection Windows NT 4.0 does not support infrared communication. By default, the infrared port is not enabled. You must enable it in the BIOS Setup utility and then install the appropriate infrared driver. For details, refer to the driver’s Readme file located in \OmniBook\drivers\Win95.
Page 75
Making Connections Transferring Files with an Infrared Connection To transfer files, you can use the Direct Cable Connection software built into Windows 95. You need to install it first. 1. From Control Panel, click Add/Remove Programs. 2. Click Windows Setup, Communications, and select Direct Cable Connection. See the Windows 95 online help for instructions about how to use Direct Cable Connection.
Making Connections Using PC Cards This section describes how to Insert a PC Card. Remove a PC Card. Select a compatible PC Card from a list of tested cards. To insert a PC Card Windows NT 4.0 does not support zoomed video. If you are using Windows NT 4.0, make sure you’ve installed Card Executive (see page 6-18 for instructions).
Making Connections To remove a PC Card Do not remove a PC Card while the OmniBook is actively reading or writing data. Otherwise, you could lose data or the OmniBook could stop responding. When the card is active, the PC Card indicator appears on the status panel. PC Card indicator 1.
At the time of this printing, the following cards have been tested for use with the OmniBook. For the latest information about compatible cards, visit our website at http://www.hp.com/omnibook and check the Accessories section. Or contact Hewlett-Packard as described in the Support and Service booklet. 3COM...
Your dock requires a tray that accommodates your specific OmniBook model. Install this tray prior to connecting the OmniBook to the dock. 1. Select the tray labeled for the OmniBook 7100. 2. Slide the rear of the tray into the dock as shown on the dock label.
Making Connections To dock the OmniBook 1. If you’re using Windows NT, click Start, Shut Down. 2. Plug the power cord into the ac adapter, then into an ac outlet. Plug the ac adapter into the dock. 3. On the rear of the OmniBook, slide the docking door to the left. 4-20...
Page 81
Making Connections 4. Place the OmniBook on the dock platform, with the rear of the computer facing the dock’s docking connector. 5. Position your fingers on the platform grips as shown below. Use your thumbs to push the computer into the dock until the computer slides into place. 4-21...
Making Connections To undock the OmniBook 1. If you’re using Windows NT, click Start, Shut Down. 2. Press the undock button on the front of the dock and wait for the undock light to turn green. Then position your thumb as shown and pull the release lever forward.
Page 84
Expanding the OmniBook This chapter describes some of the optional equipment that can be added to the OmniBook—components installed inside the computer rather than connected to the computer’s I/O ports. This chapter describes procedures to expand or update the capabilities of your OmniBook, including Installing a hard disk drive.
Expanding the OmniBook Installing a Hard Disk Drive This section describes how to Replace the hard disk drive. Replace the hard disk drive holder. Create a hibernate partition for a new hard disk drive. To replace the hard disk drive 1.
Expanding the OmniBook To replace the hard disk drive holder If you are installing a new hard drive that does not have a plastic holder, you can remove the holder from the old hard drive. You’ll need a small Phillips screwdriver for this procedure. 1.
Expanding the OmniBook To create a Hibernate partition You’ll need the OmniBook, its CD-ROM drive, and the OmniBook Recovery CD to create a hibernate partition. 1. Connect the ac adapter to the OmniBook. 2. Insert the CD-ROM drive in the OmniBook. 3.
Expanding the OmniBook Installing a RAM Expansion Module The OmniBook provides an optional memory expansion slot for installing a 3.3-volt EDO RAM expansion module. This section describes how to Install a RAM expansion module. Remove a RAM expansion module.
Expanding the OmniBook To install a RAM expansion module Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can permanently damage computer chips. Before starting, reading the caution on page 5-6 about how to handle RAM expansion modules. 1. Unplug the ac adapter, if present, and remove the battery. 2.
Expanding the OmniBook To remove a RAM expansion module Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can permanently damage computer chips. Before starting, reading the caution on page 5-6 about how to handle RAM expansion modules. 1. From the Start menu, shut down the OmniBook. 2.
Page 92
Using the Recovery CD You can use the OmniBook Recovery CD to recover an original OmniBook build, or you can use it to install the HP custom software over a user-installed alternate operating system. The Recovery CD provides the OmniBook-specific drivers to configure your custom system.
Using the Recovery CD Recovering a factory build If you’ve deleted or lost files on the OmniBook, causing the system to work improperly, you may need to recover the original factory build. This section describes how to Recover the OmniBook factory installation of Windows 95. Recover the OmniBook factory installation of Windows NT 4.0.
2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)
2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)
3. Connect the ac adapter and turn on the OmniBook. 4. When you see the HP logo, press F2 to enter the BIOS Setup utility. 5. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)
Page 97
Using the Recovery CD 10. Create the Primary and Extended DOS partitions. You will need at least 300 MB for the Primary Partition. 11. Make the C: an active partition. 12. Choose Exit to MS-DOS from the Windows 95 Startup Menu. 13.
Using the Recovery CD 27. Copy the files in D:\Omnibook from the OmniBook 7100 Recovery CD to C:\Omnibook. To install video support for retail Windows 95 If you’ve installed a retail version of Windows 95, you’ll need to install video support.
Using the Recovery CD To install audio support for retail Windows 95 If you’ve installed a retail version of Windows 95, you’ll need to install audio support. This driver is located on the OmniBook’s hard drive or on the Recovery CD in \Omnibook\Drivers\Win95\Audio.
2. If prompted to overwrite old files, click Yes. 3. Reboot the OmniBook. 4. When you see the HP logo, press F2 to enter the BIOS Setup utility. 5. Go to the System Devices menu. 6. Set the Infrared Port to Enabled.
Page 101
Using the Recovery CD 11. Save and exit the BIOS Setup utility. 12. When prompted for a driver disk, select the driver disk provided by the hardware manufacturer, then click OK. 13. Enter the directory of the infrared drivers (\Omnibook\Drivers\Win95\Fastir) and click OK.
Using the Recovery CD Installing Retail Windows NT 4.0 If you install a retail version of Windows NT 4.0 you’ll also need to manually install video, audio, Advanced Power Management (APM), and Card Executive drivers. This section describes how to Install a retail version of Windows NT 4.0.
2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. From the Boot menu, select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)
Using the Recovery CD When choosing a file system, refer to the Windows NT Resource Kit for a detailed discussion of FAT and NTFS file systems. 13. When prompted, choose No, Do Not Create An Emergency Repair Disk, then click Next. If is more useful to create a repair disk after installation is complete and after you have installed your drivers and other applications.
Using the Recovery CD To install video support for retail Windows NT 4.0 If you’ve installed a retail version of Windows NT 4.0, you’ll need to install video support. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Video. 1. Insert the Recovery CD into the CD-ROM drive. 2.
Using the Recovery CD To install audio support for retail Windows NT 4.0 If you’ve installed a retail version of Windows NT 4.0, you’ll need to install audio support. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Audio. 1. Insert the Recovery CD into the CD-ROM drive. 2.
Using the Recovery CD To install APM for Windows NT 4.0 You need to install Advanced Power Management for Windows NT 4.0 for both the retail and factory-installation. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Apm. Phoenix APM 2.0 adds the following capabilities to the OmniBook: Improved battery life under Windows NT 4.0.
Using the Recovery CD To install Card Executive 2.x for retail Windows NT 4.0 To take advantage of Card Executive’s plug-n-play for PCMCIA network cards, you must install Card Executive before installing Windows NT networking. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Pccard. Card Executive adds the following capabilities to your OmniBook: Plug and Play for PC Cards using standard Windows NT drivers.
If you lose or damage the Recovery CD, take your OmniBook and Certificate of Authenticity to an HP Service Center to be replaced. If you mail your OmniBook for this service, you must provide a photocopy of the Certificate of Authenticity along with payment.
To update the OmniBook BIOS Hewlett-Packard may update the BIOS to enhance the capabilities of the OmniBook. Updates will be available from HP Electronic Support Services. From the Start menu, shut down the OmniBook. Connect the ac adapter to the OmniBook.
Look at the online Help for Windows and other applications. Find technical information about the OmniBook on the Internet—visit the Support website at http://www.hp.com/omnibook. See other books about Windows, MS-DOS, and other applications. Check your local library or bookstore.
If you always want to boot from a CD, check boot order in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...
Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Audio is enabled.
Troubleshooting Display Problems If the OmniBook is on, but the screen is blank Press the space bar to see if the computer is in Standby mode. Press Fn+F1 or Fn+F2 to adjust the display. Press Fn+F5 in case the internal display was disabled. (Do this three times to return to the state you started from.) If the OmniBook is cold, allow it to warm up.
Make sure the touch pad or pointing stick is enabled in the BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check Internal Pointing Devices.
Check settings in BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Infrared Port is enabled.
Troubleshooting Memory Problems If a message says you are out of memory In Windows Help, search for Memory Troubleshooter. If you are having memory problems running MS-DOS programs, in Windows Help search for MS-DOS troubleshooter. PC Card (PCMCIA) Problems If the OmniBook doesn’t recognize a PC Card Make sure Card Executive is installed for Windows NT.
Check the BIOS Setup settings. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Power menu, set the Power Management Mode to Max.
1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Power menu, make sure the Power Management Mode is set to Maximum Power Savings.
Page 121
Troubleshooting Turn off the OmniBook, then check that the battery contacts are clean and that the ac adapter cables are fully plugged in. Move the OmniBook away from any nearby heat source. Unplug the ac adapter and allow the battery to cool down. An elevated battery temperature prevents charging.
If the printer you are using is a 600-dpi (dots per inch) printer, try selecting a compatible printer driver for a 300-dpi printer. For example, for a 600-dpi HP LaserJet printer, try using the HP LaserJet IIIsi driver (300-dpi). Certain applications may not work properly with 600-dpi printers.
Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Parallel and Serial are enabled.
Check boot order in BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...
\Dmi\Hpdiags directory on the hard disk. –or– If HP TopTools is installed, use the DiagTools page to create the disk. On any computer with a CD-ROM drive, run from the \Omnibook\Dmi\Hpdiags directory on the OmniBook 7100 Recovery CD.
Troubleshooting To run the diagnostic test 1. Insert the diagnostic disk in the floppy drive. 2. Reboot the OmniBook. 3. Go through the first several screens. 4. When the hardware detection finishes, check the list of detected hardware. If a device is not detected or fails its test below, it may be configured incorrectly in the BIOS Setup utility.
Specifications and Regulatory Information Your OmniBook is designed to provide trouble-free operation. The following suggestions can help you maintain its dependability: Observe the temperature limits and other specifications listed in the next section. If you have problems, see the problem-solving suggestions chapter 7 of this manual.
Specifications and Regulatory Information Hardware Specifications Size: 324mm×252mm×56mm (12.76”×9.92”×2.22”) closed. Weight: 3.95 kg (8.7 lb). 266-MHz Intel Pentium II processor with MMX technology. 1.6-V core, 2.5-V external, low-power processor. 32-KB (16-KB instruction, 16-KB data) L1 cache. 512-KB pipeline-burst-synchronous L2 cache. 32-bit PCI bus.
Page 130
Microsoft Windows 95 or Windows NT 4.0. Windows 95-compatible Plug-and-Play. Windows NT 4.0 APM and PC Card Plug-and-Play. Advanced Power Management (APM 1.2). DMI 2.0 with HP TopTools 2.6. McAfee Virus Scan 3.1.5. Online documentation. OmniBook Recovery CD included. Centralized worldwide BIOS and driver update service.
Specifications and Regulatory Information Software System Resources Below are default values for the system resources. To see other, non-default possibilities, refer to the BIOS Setup utility, which lists port and audio device configurations in the Input/Output menu. The tables in this section show typical resource usage as set up by the OmniBook BIOS.
Page 132
Specifications and Regulatory Information Valid uses for memory addresses D0000-DBFFF: Upper memory blocks (UMBs). PC Card memory windows. 170-177 Secondary HDD controller (internal CD-ROM) 1F0-1F7 Internal hard disk 220-22F Crystal sound Secondary HDD controller (internal CD-ROM) 378-37F LPT1 (printer port) 388-38B Sound 3B0-3BB...
To purchase a power cord (including one for a country not listed below) or a replacement ac adapter (HP part number F1454A), contact your local Hewlett-Packard dealer or Sales and Service office.
Page 134
When discarding a battery pack, contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. To obtain a replacement battery, contact your local dealer or HP sales office. Do not charge the battery pack if the ambient temperature exceeds 45 °C...
Page 135
EN60825-1). This device is not considered harmful, but the following precautions are recommended: Ensure proper use by reading and following the instructions carefully. If the unit requires service, contact an authorized HP service center—see the OmniBook Support and Service booklet. Do not attempt to make any adjustment of the unit.
Specifications and Regulatory Information Regulatory Information This section presents information that shows how the OmniBook complies with regulations in certain regions. Any modifications to the OmniBook not expressly approved by Hewlett-Packard could void the authority to operate the OmniBook in these regions.
(415) 857-1501 declares that the product(s) Hewlett-Packard Company HP OmniBook 7100 Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the EC mark accordingly. The HP F1454A ac adapter used with this product is designed to operate on all power systems, other than IT power systems. [1] The product was tested in a typical configuration with Hewlett-Packard personal computer peripherals.