Page 2
Document History Edition Date Board Artwork Revision First May 2010 Rev 1 Waste Electrical and Electronic Equipment (WEEE) Returns GE Intelligent Platforms Limited is registered with an approved Producer Compliance Scheme (PCS) and, subject to suitable contractual arrangements being in place, will ensure WEEE is processed in accordance with the requirements of the WEEE Directive. GE Intelligent Platforms Limited. will evaluate requests to take back products purchased by our customers before August 13, 2005 on a case by case basis. A WEEE management fee may apply. Publication No. CPCI3UX606-HRM/1...
1 • CPCI3UX606 The information contained in this manual must be used in conjunction with the I/O Modules Manual. LINK I/O Modules Manual, publication number RT5154. 1.1 Description The CPCI3UX606 module is a customized interface adapter, compatible with 3U CompactPCI backplanes. It fits directly onto the rear P2 position of the backplane and is only suitable for interconnection with the IMP3A host card. See the I/O Modules Manual ‐ Compatibility Tables for more information. The CPCI3UX606 is suitable for fitting in rear guide‐rails, according to IEEE1101.11. Figure 1-1 CPCI3UX606 4 CPCI3UX606 Publication No. CPCI3UX606-HRM/1...
Do not fit a jumper across the E1 pins. If a build option that provides USB has been selected, linking these pins will short USB_PWR to ground, which may cause damage to the IMP3A. Figure 1-2 RS422/485 Signal Definition Publication No. CPCI3UX606-HRM/1 CPCI3UX606 5...
Availability of signals at the various connectors depends on the I/O option selected on the IMP3A. See the hardware reference manual for more details. LINK IMP3A Hardware Reference Manual, publication number IMP3A-HRM. 1.3 Breakout Panel Connectivity Table 1-3 Breakout Panel Connectivity Breakout Panels CPCI3UX606 header P2 6 CPCI3UX606 Publication No. CPCI3UX606-HRM/1...
J14-60 J14-61 J14-62 J14-63 J14-64 1.4.6 P6 (SATA0) NOTE Availability of signals at this connector depends on the build option selected on the IMP3A. Use a right‐angled SATA cable to remain within the allowable height limit. Table 1-10 P6 Pin Assignments Signal SATA0_TX+ SATA0_TX- SATA0_RX- SATA0_RX+ 10 CPCI3UX606 Publication No. CPCI3UX606-HRM/1...
Table 1-11 P6 Pin Assignments Signal SATA1_TX+ SATA1_TX- SATA1_RX- SATA1_RX+ 1.4.8 P8 (COM1) See the P2 description for more details on COM1. Table 1-12 P8 Pin Assignments Signal Pin Signal No connection No connection COM1_RXD (RXD_A) COM1_CTS (RXD_B) COM1_TXD (TXD_A) COM1_RTS (TXD_B) No connection No connection Publication No. CPCI3UX606-HRM/1 CPCI3UX606 11...
Table 1-14 P10 Pin Assignments Signal Pin Signal ETH1_3- COM1_RTS 4 ETH1_3-_GPIO11_COM1_RTS GPIO11 1.4.10 J3 (10/100/1000BaseT Ethernet Channel 0) Gigabit operation depends on availability of the required signals, which is an IMP3A build option (see also P1). 10/100 signals are given in parentheses. Table 1-15 J3 Pin Assignments Signal ETH0_0+ (TX+) ETH0_0- (TX-) ETH0_1+ (RX+) ETH0_2+ ETH0_2- ETH0_1- (RX-) ETH0_3+ ETH0_3- 12 CPCI3UX606 Publication No. CPCI3UX606-HRM/1...
ETH1_2+ ETH1_2- ETH1_1- (RX-) ETH1_3+ ETH1_3- 1.4.12 J5 (USB) NOTE Availability of signals at this connector depends on the build option selected on the IMP3A. Table 1-17 J5 Pin Assignments Signal USB_PWR USB_D- USB_D+ The IMP3A provides USB_PWR when a USB build option is selected. Publication No. CPCI3UX606-HRM/1 CPCI3UX606 13...
Page 14
Figure 1-4 CPCI3UX606 with Front Panel Figure 1-5 CPCI3UX606 in Rear Guide Rails (per IEEE1101.11) 14 CPCI3UX606 Publication No. CPCI3UX606-HRM/1...
Page 15
1 800 322 3616 or 1 256 880 0444 Confidential Information - This document contains Confidential/Proprietary Information www.ge-ip.com of GE Intelligent Platforms, Inc. and/or its Asia Pacific: suppliers or vendors. Distribution or 86 10 6561 1561 reproduction prohibited without permission.