(with an operating distance of approx. 5 m/16.4 ft. in any direction). * For information on the supported cameras, refer to the Canon Web site, etc. Features of the BR-E1 • Shooting still photos and movies •...
Bluetooth SIG, Inc. and any use of such marks by Canon Inc. is under license. Other trademarks and trade names are those of their respective owners. The Wi-Fi CERTIFIED logo and the Wi-Fi Protected Setup mark are ...
Contents Introduction..................2 Features of the BR-E1 ..............2 Conventions Used in this Manual............. 3 Safety Precautions ................5 Handling Precautions ............... 6 Holding the Remote Controller ............6 Cautions for Using the Remote Controller........7 Nomenclature ................... 8 Connecting the Remote Controller and Camera ......9 Checking Registered Information/Removing Registration....11...
Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Follow the warnings below. Otherwise, death or Warnings: serious injuries may result.
Handling Precautions Do not immerse the product in water. Wipe off any water droplets with a dry and clean cloth. If the product is exposed to salty air, wipe it with a clean, well-wrung wet cloth. Holding the Remote Controller When operating the remote controller, hold it as indicated in the ...
Cautions for Using the Remote Controller If remote control operation takes time or fails, or if other problems occur, try the following corrective actions. Distance Between the Camera and This Product The operating distance of this product is approx. 5 m/16.4 ft. in all directions.
Set the camera to the pairing standby mode. Select [Pairing] from the menu screen of the camera. For details, refer to the pages regarding BR-E1 in the Camera Instruction Manual. Connect the remote controller to the camera. Press and hold the <W> button and ...
Page 10
Connecting the Remote Controller and Camera Pairing with two or more cameras simultaneously is not possible. If you pair a camera and the remote controller that has already been paired with another camera, remote operation of the previously paired camera cannot be performed. Remove the registration of the remote controller, then pair with the other camera.
Instruction Manual. Removing Registration To use a paired (registered) remote controller with another camera or to perform pairing again, remove the registration of the remote controller. For the operation procedure, refer to the page regarding BR-E1 in the Camera Instruction Manual.
Shooting Still Photos Set up the camera for remote control shooting. Set the camera for still photo shooting. Set the drive mode of the camera to < > (remote control). Select the release method. Set the release timing/movie shooting ...
Shooting Movies Set up the camera for remote control shooting. Set the camera for movie shooting. Set [Remote control] to [Enable] from the menu screen of the camera. Set the switch to < >. Set the release timing/movie shooting ...
Operating the Power Zoom Adapter The Power Zoom Adapter is a lens accessory (sold separately). For information on how to attach to the lens and operate the Power Zoom Adapter, refer to its Instruction Manual. Prepare the Power Zoom Adapter. Attach the Power Zoom Adapter to ...
Replacing the Battery If the indicator lamp does not light up when you press a button on the remote controller, replace the battery. Use one lithium button cell battery CR2032. CR2032 Make sure to insert the battery with the positive (+) side face up, as indicated in the figure above.
Approx. 14 g/0.49 oz. (excluding battery) Working temperature range: 0°C - 40°C / 32°F - 104°F Working humidity: 85% or less All the data above is based on Canon’s testing standards. Product specifications and the exterior are subject to change without notice. ...
Use of wireless communication function is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating wireless regulations, visit the Canon Web site to check where use is allowed. Note that Canon cannot be held liable for any problems arising from wireless communication function use in other countries and regions.
Page 18
Wireless Communication Function Model: DS586111 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Index Numerics 2-sec. delay release......8 Release button ....... 12 Removing registration ....11 Replacing the battery ..... 15 AF start button ........8 Safety Precautions ......5 Bluetooth...........9 Shooting movies......13 ............8 Shooting still photos ....... 12 Switch........8, 12, 13 Checking registered information ..11 Connecting........9 Trademark ........
Page 20
The descriptions in this Instruction Manual are current as of February 2017. For information on the compatibility with any products introduced after this date, contact any Canon Service Center. For the latest version Instruction Manual, refer to the Canon Web site.