Epson UB-S01 User Manual

https://support.epson.net/p_doc/939/
Standards and Approvals
The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the Epson
power supplies and TM series printers.)
Les normes suivantes ne s'appliquent qu'aux cartes d'interface ainsi étiquetées. (CEM est testé à l'aide des blocs
d'alimentation Epson et des imprimantes de la série TM.)
Europe: CE marking North America/Amérique du Nord: FCC/ICES-003 Class A
Japan: VCCI Class A Oceania: AS/NZS CISPR22 Class A
CE Marking
These products conform to the following Directive and norms:
Directive 2004/108/EC
EN 55022 Class A
EN 55024
IEC 61000-4-2 IEC 61000-4-3
IEC 61000-4-4 IEC 61000-4-5
IEC 61000-4-6 IEC 61000-4-11
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user
may be required to take adequate measures.
The printers in which this board is installed becomes class A devices.
The connection of a non-shielded printer interface cable to this board will invalidate the EMC standards of this device.
You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your
authority to operate the equipment.
AVERTISSEMENT
Cet appareil est un produit de classe A. Dans un environnement résidentiel, il risque de provoquer un brouillage radio,
auquel cas l'utilisateur pourra être tenu de prendre des mesures adéquates.
Les imprimantes dans lesquelles cette carte est installée deviennent des appareils de classe A.
La connexion d'un câble d'interface d'imprimante non blindé à cette carte invalidera les normes CEM de cet appareil.
Vous êtes averti que les changements ou modifications non expressément approuvés par Seiko Epson Corporation
peuvent invalider votre droit à faire fonctionner l'équipement.
FCC Compliance Statement for Users in the USA
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
For Users in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
User's Manual / Manuel d'utilisation / ユーザーズマニュアル
English Français Español
日本語
Română Українська
English
Introduction
Türkçe
This manual describes how to replace the UB-S01 on TM series printers designed for this board.
You must check the printer DIP switches after replacing the UB-S01.
See the documentation that came with the printer for information about setting the DIP switches.
About the Symbol in This Manual
CAUTION:
Cautions must be observed to avoid minor injury to yourself or damage to your equipment.
Precautions
CAUTION:
Disconnect the power supply from the printer before you remove the UB-S01; otherwise you may damage the UB-S01
and the printer. You must disconnect the power supply because the electrical current is flowing in some parts of the
printer circuit even when the power switch is turned off.
Wear a grounded wrist strap when handling the UB-S01 to prevent damage from static electricity.
To avoid contamination, do not touch the board connector.
Unpacking
Make sure you have these items:
O UB-S01
O Manuals
Procedure
1. Remove the two screws that securing the UB-BOARD; then pull
the UB-BOARD to remove it.
CAUTION:
Put the UB-BOARD into an anti-static bag for storage to prevent
damage from static electricity.
2. Hold the UB-S01 as shown in the illustration below. Push the
UB-S01 in gently until you feel the connector fit into place.
3. Secure the UB-S01 with the two screws.
4. Change the printer DIP switches to match the printer to the
new interface.
See the printer documentation for information about these
settings.
Make sure you set the printer DIP switches. Otherwise the
printer may not work correctly.
©Seiko Epson Corporation 1997–2023
Connector of the UB-S01
Connector of the TM printer
Printed in XXXXXX
Imprimé XXXXXX
Impresso XXXXXX
Impreso en XXXXXX