Husqvarna RZ3016 Operator's Manual

Zero turn mower

Hide thumbs Also See for RZ3016:

Operator's manual (64 pages)

Parts manual (32 pages)

Operator's manual (56 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Husqvarna RZ3016

Page 1 Operator Manual RZ3016 Zero Turn Mower / 966612301-04 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10)
Page 2: Conformity Certificates
CONFORMITY CERTIFICATES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels.
Page 3: Table Of Contents
CONTENTS INTRODUCTION ............... 4 Mowing Tips ............. 18 Driving and Transport on Public Roads ...... 4 Operating On Hills ............ 19 Towing ................. 4 Weak Battery ............19 Operating ..............4 Jumper Cable Use ..........19 Good Service .............. 5 Moving Machine By Hand ........
Page 4: Introduction
INTRODUCTION Congratulations Operating Thank you for purchasing a Husqvarna ride-on mower. This This machine is constructed only for mowing grass on lawns machine is built for superior efficiency to rapidly mow primarily and even ground without obstacles such as stones, tree large areas.
Page 5: Good Service
INTRODUCTION Good Service Husqvarna's products are sold only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer.
Page 6: Symbols And Decals
SYMBOLS AND DECALS These symbols are found on the machine and in the operator manual. Study them carefully so that you know what they mean. IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx WARNING! xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Page 7: Safety
SAFETY Safety Instructions General Operation These instructions are for your safety. Read them carefully. • Read, understand, and follow all instructions on the machine and in the manual before starting. WARNING! THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING •...
Page 8: Personal Safety Equipment
SAFETY • Always wear eye protection when operating machine. • Wear proper Personal Protective Equipment (PPE) while WARNING! Do not drive up or down hills with slopes operating this machine, including (at a minimum) sturdy greater than 10 degrees. Do not drive across any slopes. footwear, eye protection, and hearing protection.
Page 9: General Maintenance
SAFETY • Remove gas-powered equipment from the truck or trailer • Never make adjustments or repairs with the engine running. and refuel it on the ground. If this is not possible, refuel • Check the park brake’s functionality regularly. Adjust and such equipment with a portable container, rather than from service as necessary.
Page 10: Transport
A spark arrestor for the muffler is available through your machine down with approved devices such as bands, authorized Husqvarna dealer. chains or straps. • Both front and rear tie down straps should be used and directed down and outward from the machine.
Page 11: Controls
CONTROLS This operator manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a Briggs & Stratton four-stroke overhead valve engine. Transmission from the engine is made via a belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed.
Page 12: Steering Control Levers
CONTROLS Steering Control Levers WARNING! The machine can turn very rapidly if one steering control is moved much further forward than the other. Park Brake The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position.
Page 13: Throttle Control
CONTROLS Throttle Control Refueling The throttle control regulates the engine speed and thereby Read the safety instructions before refueling. The machine has the rate of rotation of the blades, assuming the blade switch is one fuel tank, just behind the seat. The tank volume is 11.4 pulled out, see Engaging the Mower Deck.
Page 14: Fuel Shut Off Valve
Mower Deck Lifting Lever bar) Tracking must be checked on a flat and level concrete or blacktop surface. If the unit still does not track straight contact your Husqvarna workshop for adjustments. Bypass Linkages Transaxle bypass linkages must be engaged when pushing or pulling the mower.
Page 15: Operation
OPERATION Before Starting Read the Safety section and following pages, if you are unfamiliar with the machine. Read the sections on Safety and Controls before starting the machine. Training Perform the daily maintenance before starting (see Due to unique steering capabilities, zero turn mowers are far Maintenance Schedule in the Maintenance section).
Page 16 OPERATION Disengage the mower blades by lowering the blade F, move the throttle lever If the temperature is below 32 control lever out of the lock notch and into the down up to the cold weather (snowflake) starting position. position. When the engine has started, move the throttle lever back to full throttle detent and allow the engine to warm up for a short period before operating the unit.
Page 17: Running
OPERATION Move throttle control to full throttle. WARNING! Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
Page 18: Stopping The Engine
OPERATION Stopping the Engine Mowing Tips Disengage the mower deck by sliding the blade control • Observe and flag rocks and other fixed objects to avoid lever out of the lock notch and down into the lower collisions. position. • Begin with a high cutting height and reduce it until the desired mowing result is attained.
Page 19: Operating On Hills
OPERATION Weak Battery Operating On Hills If the battery is too weak to start the engine, it should be Read the Safety Instructions Driving on Slopes in the Safety recharged. (See Battery in the Maintenance section.) section. If jumper cables are used for emergency starting, follow this •...
Page 20: Maintenance
MAINTENANCE Maintenance Schedule The following is a list of maintenance procedures that must be recommended to maintain your machine in the best possible performed on the machine. For those points not described in condition and to ensure safe operation. this manual, visit an authorized service workshop. An annual Read Maintenance in the Safety section.
Page 21: Battery
Perform a standstill test Reinstall battery. and check that there is sufficient braking action. Replacing battery To adjust the park brake, contact the Husqvarna service Lift seat and rotate forward. workshop. Open terminal access doors Using two ½"...
Page 22: Safety System
MAINTENANCE Safety System V-belts The machine is equipped with a safety system that prevents Check every 100 hours of operation. Check for severe starting or driving under the following conditions. cracking and large nicks. The engine can only be started when: NOTE: The belt will show some small cracks in normal operation.
Page 23: Tire Pressures
Tighten blade bolt securely. Reinstall in reverse order. Tighten caster bolt. Torque blade bolt to 50 ft/lbs (67 Nm). IMPORTANT INFORMATION Special blade bolt is heat treated. Replace with a Husqvarna bolt if required. Do not use lower grade hardware than specified.
Page 24: Adjusting The Mower Deck
MAINTENANCE Adjusting the Mower Deck Cleaning Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span. Make it a habit to CAUTION! Blades are sharp. Protect your hands clean the machine directly after use (after it is cooled), before with gloves and/or wrap blades with a heavy cloth the debris sticks.
Page 25: Lubrication
Transmission The transmission is maintenance free with no need for level checks or oil changes. If a leak occurs, replace the unit or contact your Husqvarna dealer. Engine Refer to the engine manufacturer's manual for maintenance and service instructions.
Page 26: Troubleshooting
TROUBLESHOOTING Problem / Cause Engine will not start Engine overheats Blade switch is engaged Clogged air intake or cooling fins Steering controls are not locked in the neutral position Engine overloaded Park brake is not activated Poor ventilation around engine Battery is dead Defective engine speed regulator Contamination in the carburetor or fuel line...
Page 27: Storage
Never use Always use genuine Husqvarna spare parts. gasoline for cleaning. Use a degreaser and warm water. An annual check-up at an authorized service workshop is a good way to ensure that your machine performs its best the following season.
Page 28: Schematic
SCHEMATIC...
Page 29: Technical Data
TECHNICAL DATA Engine Frame Manufacturer Briggs & Stratton Cutting Width 30" / 76 cm Type Endurance Cutting Height 1½" - 4" / 2.5 cm - 10.6 cm Power 16.5 HP Uncut Circle Lubrication Pressure with oil filter Number of Blades Fuel Min 86 octane unleaded (Max Blade Length...
Page 30: Torque Specifications
TECHNICAL DATA Torque Specifications Standard ¼" fasteners 9 ft/lb (12 Nm) Engine crankshaft bolt 75 ft/lb (100 Nm) Standard " fasteners 18 ft/lb (25 Nm) Deck pulley bolts 75 ft/lb (100 Nm) Standard " fasteners 33 ft/lb (44 Nm) Lug nuts 75 ft/lb (100 Nm) Standard "...
Page 31: Service Journal
SERVICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service Charge the battery Adjust the tire pressure of all wheels to 15 PSI (1 bar) Mount the steering controls in the normal position Connect the contact box to the cable for the seat’s safety switch Check that the right amount of oil is in the engine Adjust the position of the steering controls Fill with fuel and open the fuel shut off valve...
Page 32: Hour Service
SERVICE JOURNAL Action Date, mtr reading, stamp, sign After the First 10 Hours Change engine oil Date, mtr reading, stamp, sign 25-Hour Service Check the fuel pump’s air filter Sharpen/Replace mower blades if required Check the tire pressures Check battery with cables Lubricate according to lubrication chart Check/clean the engine’s cooling air intake Clean the air cleaner’s foam pre-filter...
Page 33 SERVICE JOURNAL Action Date, mtr reading, stamp, sign 100-Hour Service Perform the 25-hour service Perform the 50-hour service Change the engine oil filter Clean/replace the spark plugs Replace the fuel filter Check V-belts Check tighten caster wheel axle bolts (every 200 hours) Change the air filter’s paper cartridge Change hydraulic pump oil and filter.
Page 34 SERVICE JOURNAL Action Date, mtr reading, stamp, sign At Least Once Each Year Clean the engine’s cooling air intake (25 hours) Replace the air cleaner’s foam pre-filter (300 hours) Replace the air filter’s paper cartridge Change the engine oil (50 hours) Replace the engine oil filter (100 hours) Check/adjust the cutting height Check/adjust the park brake (50 hours)
Page 36 115 71 02-27 Rev A 2014-08-01...

Husqvarna RZ3016 Operator's Manual

Quick Links

Related Manuals for Husqvarna RZ3016

Summary of Contents for Husqvarna RZ3016

Table of Contents