Pioneer PD-M90X Operating Instructions Manual page 25

OPERATION
WITH REMOTE CONTROL
UNIT
Remote control
unit
enables various key function
operations
from a
distance.
Remote
control unit
enables
the following functions.
o
Programming
into
memories
A to
H on
remote
control
unit.
o Transmit programs in
A to
H
to
player.
o Adjust
reproduction volume
of
compact
disc.
Normal Remote Control
Operation
Normal remote control operation
is
possible
when
all the
A
-
H memory symbols are lit on the
remote
control unit display. (Key operations on the
remote
control unit
will
be transmitted
to the
player.)
DISC NO., TRACK
NO.,
PLAY,
RANDOM PLAY PAUSE
ANd
LEVEL key can all be displayed on the indicator.
To change displayed
disc number
and
track
number,
press DISC NO. and TRACK NO. keys
again.
DIGITAL LEVEL
CONTROLLER
By
pressing the
LEVEL
-
and
a
keys
the
digital
circuit
will
control
the
level(volume)
in
1 dB
steps
from 0 dB to
- 25
dB.
o
Raise
the volume by pressing
the *
level
key.
(At 0
dB the level is not
changed.)
o
Lower the volume by pressing the
- level
key.
(When pressed continuously,
it
will
stop at
-25
dB)
The
DIGITAL
LEVEL CONTROLLER indicator and
the
SEC display
will
show the following
indications.
(Digital level controller
indicator)
0 :
lights when the
level
is 0
dB
-6 :
lights when the
level
is
between
0
-
-O
dB
-12: lights when the level is between 0
-
-12
dB
-24
'.
lights
when the
level
is
beween
0 -
-24d8
Player display
The level
will
be
indicated
for two
seconds
when
the
key is
pressed.
When the
level
is
-12 dB,
it
will
be
displayed
as
follows.
Minute
section
Second
section
rt:
The level is 0 dB when the power is turned on
and
should be normally be used
it
in this condition.
The
digital
level controller can be
used
to
modify
the
output level
for the
rear terminals
as well as
the
headphone jack.
PROGRAMMING, TRANSMISSION, START
OF
PLAYBACK
1.
Press
MEMORY
keys
A
-
H.
Make sure
that selected memory indicator
lights.
Select
DISC No. key and
TRACK
No.
key.
Press PGM
MEMORY key.
Repeat operations
2
and
3.
Proceed
as
described
in 1
-
4
above to
program
the other
memoraes, too.
NOTE:
o
Each memory has
a
capacity
of
32
steps
and
the
total
memory capacity
of the remote control unit is
80
steps.
Any steps programmed
in
excess
of
memory
capacity
will not be
memorized.
(When
the 80
step
memory
capacity
is
exceeded,
the
indicator
will
show
an
"Err"
message.)
C
Operations
to
add, correct and clear programs
are
the
same
as for player
operations.
o
When
the
memory
is
be|ng read and
a
program
is
being input,
commands
by pressing the
remote
control
keys
will not be
transmitted
to
the player. To
control
the player, the memory write mode will
first have
to
be
cancelled.
(
To
enter
a
program
in
memory
B,
press key
B.)
Press
the
B
key after the player has been
con-
trolled and the remote control unit
will again be in
memory write
mode.
Transmlssion
to
Player and Start
of
Playback
6.
Press
MEMORY
key
(A-H)
to
be
transmit-
ted.
Make sure
that selected memory indicator
lights.
7.
Press TRANS
key.
During program transmission
(the
indicator
is flashed),
the remote control unit should
be aimed at the player.
NOTE:
o
lf
there
are
obstacles
in
the way, the
distance too great
or
the angle between the player and the
remote control
unit
is
not appropriate, transmission
may not
be
possi-
ble.
o
The program stored
in
the player
will
then
be cleared,
and the player will
enter the
stop mode.
o
During transmission, keys other than
the
RANDOM
PLAY
and PLAY keys
cannot be
use.
8.
Press PLAY
or
RANDOM PLAY key
to
start.
25
<PR B1 01
9>
2.
3.
4.
5.
The example shows how
to
program
track 3 on
disc
2,
track
1
of disc
3,
a
pause and track 5
of
disc 1
in
memory
B.
lndicator
Display
o
Press
ITR-ANSI
to
transmit.
o
Press
mAV to
start.
Press DISC
NO.E
Press TRACK NO
E
Press
I
povuuuvoRil
Press DISC
NO.E
Press TRACK
NO.E
Press
[Fclrt
tt,tEwonyI
Press
PAUSE
Press
I
pcv
tt,tEvoRyl
Press DISC NO
E
Press TRACK
NO.E
Press
I
pGrur
verr,toRil