Zte F160 User Manual

LEGAL INFORMATION
Copyright © 2011 ZTE CORPORATION.
All rights reserved.
F160
No part of this publication may be excerpted, reproduced,
translated or utilized in any form or by any means, electronic or
Mobile Phone mechanical, including photocopying and microfilm, without the
prior written permission of ZTE Corporation.
User guide
The manual is published by ZTE Corporation. We reserve the
right to make modifications on print errors or update specifications
without prior notice.
Version No. : R1.0
ZTE CORPORATION
Edition Time : 2011.03
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Manual No. : 079594502840
Postcode: 518057
Tel: (0086) 755 26779999
URL: http://www.zte.com.cn
E-mail: mobile@zte.com.cn
Inserting the Memory Card Charging Your Phone
Your phone uses a rechargeable battery. When you first unpack
Tips:
the phone, the battery is not fully charged, but there might be
Your phone can support a memory card with an up to 8GB
enough power to turn on the phone. You should flatten the battery
capacity.
by using all of the available power before charging the battery for
the first time.
Caution:
Only use approved memory cards for this device. Any use
Open the USB port cover and insert the charger's USB adapter
of unapproved memory cards might cause loss of data or into the USB port.
damage to your phone.
Notes:
Carefully insert the memory card into the memory card slot and
y Make sure the adapter's connector is inserted correctly. Do
place the card into position.
not force the connector into the port.
y The battery will remain fully charged for 3 to 4 hours.
y If the phone is used too often when the battery is low or not
used for a long time, the screen may not display the charge
indicator until the battery has been continuously charged
for 10 to 40 minutes.
y To get the maximum performance out of your battery, it
is recommended that you completely charge the battery
before using the phone for the first time. A new battery's
full performance is only reached after three complete
charge and discharge cycles have been finished.
y Charging is only possible within a temperature range of 0°C
to 45°C.
7
Phone Overview
1 2
Power on/off the Phone
Notes:
Do not power on your phone if wireless phone use is
unapproved, or when it may cause interference or danger.
Press and hold End Key to turn on / off the phone.
Notes:
y When prompted, enter your PIN (Personal Identification
Number) code or handset code and press the OK Key.
y The PIN code is the password provided by your network
service provider. You cannot use the (U)SIM card without it.
y When the PIN code or handset code is accepted, the
phone automatically searches for the network. After a few
seconds, your phone displays standby mode.
8 9
Keypad Functions
Key
y In standby mode: Used as hot keys to activate pre-
Key Function Description
set functions.
y The bottom line of the display shows the options y In lists, messages and menus: Used to scroll up,
down, left and right.
that can be selected using the Left and Right
/
Soft Keys. The options change depending on the
y In lists and menus: Press the OK Key to start an
application/function being used.
application/function.
y Press the Voice Call Key to dial or answer calls.
y Press the number keys to enter a phone number.
y In standby mode: Press the Voice Call Key to ~
y Press and hold keys 2 to 9 to dial the associated
show a list of All Recent calls.
speed dial contact.
y Press and hold the End Key to turn the phone on/off.
y Press the * Key to enter *.
y Press the End Key to end a call.
y Press and hold the * Key to lock the keypad.
y Press the End Key to reject an incoming call.
y In an editing screen: Press the * Key to enter
y Press the End Key to cancel dialing.
punctuation and symbols.
y Press the End Key to return to the Main Menu or
y Press the # Key to enter #.
standby mode.
y In an editing screen: Press the # Key to change the
y Press the Video Call Key to dial or answer the input method.
video calls. y In standby mode: Press and hold the # Key to
y In standby mode: Press the Video Call Key to activate/deactivate meeting mode with vibration.
show a list of all calls.
y Press the C Key to delete the message or file.
Removing the Back Cover
y Press the C Key once to delete the character on the
left of the cursor when entering text or numbers.
Remove the back cover using the thumb catch at the bottom of
y Press and hold the C Key to delete all characters
the phone.
during text entry.
y Press the C Key to return to the previous page
when navigating menus or browsing the internet.
3
Standby Mode Status Bar Icons
The start up screen below is referred to throughout the guide as
3G network signal strength
the standby mode.
GSM network signal strength
New SMS
SMS memory is full
New MMS
MMS memory is Full
New E-mail
E-mail memory is Full
New Wap Push Message
Wap Push Message memory is Full
Alarm
Bluetooth on
Battery status
Vibrate mode
1 Indicators
Headset mode
2 The name of the service provider
Headset and vibrate mode
3 The function for the Left Soft Key
Silence
4 The function for the OK Key
GPRS in use
5 The function for the Right Soft Key
Missed voice call
Missed video call
10
Function Description
Installing the Battery
Notes:
If you are not going to use the battery for a long time, remove
it from the phone and store it in a cool dry place.
1. Carefully insert the battery with the contacts located against
the gold springs.
2. Push down the battery until it clicks into place.
4 5
Lock/Unlock Your Phone
Use the keypad lock to prevent the keys from being pressed
accidentally.
1. Manual Lock: In standby mode, press and hold the * Key to
engage key lock.
2. Auto Lock: In standby mode, select Menu > Settings > Phone >
Auto keyguard and set your desired time to lock the keypad.
Notes:
• If a call comes in when the keypad is locked, you can
press the Voice Call Key or Video Call Key to answer
it. When the call is ended or rejected, the keypad locks
automatically.
• When the keypad lock is on, calls might still be possible to
the emergency number(s).
11 12
Inserting the (U) SIM card
Notes:
y Do not bend or scratch your (U)SIM card. Keep the card
away from electricity and magnetism.
y Don't touch the metal surface of the (U)SIM card. Doing so
could cause information on the card to be lost or destroyed.
y Disconnect the charger and other accessories from your
phone and remove the battery before inserting and
removing your (U)SIM card.
1. Hold the (U)SIM card with the metal contacts facing
downward and the cut corner at the bottom right. .
2. Insert the card into the card holder and push it until it clicks
into position.
6
Main Menu
1 Tools 4.7 Set speed dial 5.2.1 New Email
1.1 Bluetooth 4.8 Delete contact 5.2.2 Inbox
1.2 Alarm 4.9 Advanced 5.2.3 Outbox
4.9.1 Batch send via 5.2.4 Drafts
1.3 Calendar
1.4 Stopwatch bluetooth 5.2.5 Sent
1.5 World Time 4.9.2 SIM 5.2.6 User folders
1.6 Calculator Management 5.2.7 Settings
1.7 Converter 4.9.3 Delete 5.2.8 Memory info.
2 Browser Contact(s) 6 Recent Call
3 Games & App 4.9.4 Default memory 6.1 All
4 Contacts 4.9.5 Speed Dial info. 6.2 Missed
4.1 Send message 4.9.6 Service dial 6.3 Received
4.2 Dial number 6.4 Dialed
4.2.1 Voice call 4.9.7 Memory info. 7 Profiles
4.2.2 Video call 5 Messages 7.1 General
4.3 Add new contact 5.1 Message 7.2 Meeting
5.1.1 Create message 7.3 Outdoor
4.4 Add to
4.4.1 Family 5.1.2 Inbox 7.4 Silent
4.4.2 Friends 5.1.3 Outbox 7.5 Flight
4.4.3 Work 5.1.4 Drafts 8 Multimedia
4.5 Send Bus. Card 5.1.5 Sent 8.1 Camera
5.1.6 User folders 8.2 Video camera
4.5.1 Via MMS
4.5.2 Via SMS 5.1.7 (U)SIM Inbox 8.3 FM radio
4.5.3 Via Email 5.1.8 Settings 8.4 Music
4.5.4 Via Bluetooth 5.1.9 Memory info. 8.5 Video
4.6 Edit contact 5.2 Email 8.6 Picture
13