Table of Contents
Advertisement
Available languages
Available languages
GB
Planning cooking with the electronic
programmer*
Setting the clock
After the appliance has been connected to the
power supply, or after a blackout, the display will
automatically reset to 0:00 and begin to blink. To set
the time:
1. Press the COOKING TIME button
COOKING END TIME
2. Within 4 seconds of having pressed these buttons,
set the exact time by pressing the
The
button advances the hours and the
decreases the hours.
Once the time has been set, the programmer
automatically switches to manual mode.
Setting the timer
The timer enables a countdown to be set, when the
time has elapsed a buzzer sounds.
To set the timer proceed as follows:
1. press the TIMER button
.
2. Press the
and
3. When the buttons are released the timer begins
counting down and the current time appears on the
display.
4. After the time has elapsed a buzzer will sound, and
this can be switched off by pressing any button (except
the
and
buttons). The symbol
! The timer does not switch the oven on or off.
Adjusting the volume of the buzzer
After selecting and confirming the clock settings, use
the
button to adjust the volume of the alarm buzzer.
Setting the cooking time with a delayed start
First decide which cooking mode you wish to use and
set a suitable temperature using the SELECTOR and
THERMOSTAT knobs on the oven.
At this point it is possible to set the cooking time:
1. Press the COOKING TIME button
2. Within 4 seconds of having pressed this button, set
the desired amount of time by pressing the
buttons. If, for example, you wish to set a cooking time
of 30 minutes, the display will show:
3. 4 seconds after the buttons are released, the current
time (for example 10.00) reappears on the display with
the symbol
and the letter A (AUTO).
Next the desired cooking end time must be set:
4. Press the END COOKING TIME button
5. Within 4 seconds of having pressed this button,
12
and the
simultaneously.
and
buttons.
. The display shows:
buttons to set the desired time.
will switch off.
.
and
.
adjust the cooking end time by pressing the
buttons. If, for example, you want cooking to end at
13.00, the display shows:
6. 4 seconds after the buttons are released, the current
time (for example 10.00) reappears on the display with
the letter A (AUTO).
At this point, the oven is programmed to switch on
automatically at 12:30 and switch off after 30 minutes,
button
at 13.00.
Setting the cooking time with an immediate start
Follow the above procedure for setting the cooking
time (points 1-3).
! When the letter A appears, this indicates that both
the cooking time and the end cooking time have been
programmed in AUTO mode. To restore the oven to
manual operation, after each AUTO cooking mode
press the COOKING TIME
TIME
buttons simultaneously.
! The symbol
the entire duration of the cooking programme.
The set cooking duration can be displayed at any time
by pressing the COOKING TIME button
the cooking end time may be displayed by pressing
the END COOKING TIME button
time has elapsed a buzzer sounds. To stop it, press
any button apart from the
Cancelling a previously set cooking programme
Press the COOKING TIME button
COOKING END TIME
Correcting or cancelling previously set data
The data entered can be changed at any time by
pressing the corresponding button (TIMER, COOKING
TIME or COOKING END TIME) and the
When the cooking time data is cancelled, the cooking
end time data is also cancelled automatically, and vice
versa.
If the oven has already been programmed, it will not
accept cooking end times which are before the start of
the programmed cooking process.
and END COOKING
will remain lit, along with the oven, for
. When the cooking
and
buttons.
and the
simultaneously.
WARNING! The oven is
provided with a stop sys-
tem to extract the racks
and prevent them from
coming out of the oven.(1)
As shown in the drawing,
to extract them comple-
tely, simply lift the racks,
holding them on the front
part, and pull (2).
and
, and
or
button.
Advertisement
Table of Contents
