Zte Blade L2 Quick Start Manual page 2

NOTES: Charging the battery
● SIM card 1 (the figure to the left of the
When you first get your new phone you'll
main card) support WCDMA and GSM
need to charge the battery like this:
networks; SIM card 2 only supports GSM
1. Connect the adapter to the charger
networks.
jack.
●
Switch off your phone before installing
or replacing the SIM card.
●
Please buy standardization SIM
dedicated card sets from the formal
channels，otherwise the slot shrapnel
may be pulled off when taking cards.
CAUTION: Use of Micro/Nano SIM with
/without adapter is not supported. Warranty
will be voided.
3. Inserting the memory card.
NOTE: Some applications may require a
microSD card to work normally or may store
2. Connect the charger to a standard AC
certain data on it. Therefore, it is
wall outlet.
recommended that you keep a microSD card
3. Disconnect the charger when the
installed and not remove or replace it
battery is fully charged.
randomly.
7
NOTES:
● If excessive discharge of the battery, the
charging icon will display delay.
● If the battery is extremely low, you may
be unable to power on the phone even
when it is being charged. In this case,
try again after charging the phone for at
least 10 minutes. Contact customer
service if you still cannot power on the
phone after prolonged charging.
CAUTION:Do not change the built-in
rechargeable battery in your phone by
yourself. The battery can only be changed
by ZTE or ZTE authorised service provider.
Powering On/Off Your
Phone
Make sure the SIM card is in your phone and
the battery is charged.
● Press and hold the Power Key to turn
on your phone.
● To turn it off, press and hold the Power
Key to open the options menu. Touch
Power off and then touch OK.
Restarting the Phone
If you ever encounter any problem while
using the phone, try pressing and holding
the Power Key for about 15 seconds to
restart the phone，or Press the power key
to select Reboot Device.
8 9
Waking Up Your Phone Complies with the essential protection
requirements of Directives on Radio and
Your phone automatically goes into sleep
Telecommunication Terminal Equipment
mode when it is not in use for some time.
(Directive 1999/5/EC)，Restriction of the
The display is turned off to save power and
Certain Hazardous Substances in
the keys are locked to prevent accidental
electrical and electronic
operations.
equipment(Directive 2011/65/EU),
You can wake up phone by turning on the
Eco-design Requirements for
display and unlocking the keys.
Energy-Related Products(Directive
1. Press the Power Key to turn the screen
2009/125/EC) and their
on.
amendments.This declaration applies to
all specimens manufactured identical to
2. Touch and hold at the center of
the samples submitted for
the screen. testing/evaluation.
NOTE:
Assessment of compliance of the product
If you have set an 'unlock pattern' , or a
with the requirements relating to Directive
PIN/password for your phone, you'll need to
1999/5/EC was performed by PHOENIX
draw the pattern or enter the PIN/password
(Notified Body No.0700) and assessment of
to unlock your screen.
compliance of the product with the
requirements relating to Directive
2011/65/EU and Directive 2009/125/EC was
EC Declaration of
performed by ZTE Corporation Reliability
Conformity Testing Centre. The assessments were
based on the following regulations and
standards:
It is hereby declared that following
designated product:
Product Type: WCDMA / GSM (GPRS)
Dual-Mode Digital Mobile Phone
Model No: ZTE Blade L2
Product Description: WCDMA / GSM
(GPRS) Dual-Mode Digital Mobile Phone
10
Requirement Standard Report No.
EN 50332-1-2000 ECIT-2012-
EN 50332-2-2003 0103-A
EN609501:2006+ ECIT-2012-
A11:2009+A1:201 0103
Health and
0+A12:2011 -Safety
safety
IEC 62471:2006 3125677.
EN 62209-1:2006 50A
EN 50360:2001 ECIT-2012-
EN 62311-2008 0103
EN 62479:2010 -SAR
EN 301 489-1
V1.9.2:2011
EN 301 489-3
V1.4.1:2002
ECIT-2012-
EN 301 489-7
EMC 0103
V1.3.1: 2005
-EMC
EN 301 489-17
V2.1.1: 2009
EN 301 489-24
V1.5.1: 2010
EN 300 440-1 ECIT-2012-
V1.6.1 0103-GPS
EN 300 440-2 ECIT-0103-
V1.4.1 RF-G
EN 301 511 ECIT-0103-
Radio V9.0.2 :(2003-03) RF-W
Spectrum EN 301 908-1/-2 ECIT-2012-
V5.2.1 0103-RF
EN 300 328 -BT
V1.7.1:2006 ECIT-2012-
0103-RF
-WLAN
RLSHE001
RoHS IEC 62321:2008
227150001
TRS
ErP (EC) No 278/2009
11120039
11 12
This declaration is the responsibility of the
manufacturer:
ZTE Corporation
ZTE Plaza, Keji Road South, Hi-Tech,
Industrial Park, Nanshan District, Shenzhen,
Guangdong, 518057, P.R.China
Authorised person signing for the company:
Xu Feng Quality Director Of ZTE
Corporation
Name in block letters & position in the
company
Shenzhen, February 18, 2014
Place & date Legally valid signature
This equipment may
HR AT BE
be operated in:
CY CZ DK EE FI FR
DE GR HU IE IT LV
LT LU MT NL PL PT
SK SI ES SE GB IS
LI NO CH BG RO TR
13