Operating Instructions - Grundig RR 3200 CD Service Manual

Operating Instructions

Note: This chapter contains excerpts from the operating instructions. For further particulars please refer to the
appropriate user instructions the part number of which is indicated in the relevant spare parts list.
GB
FM/RECORD MODE
OPEN/
FUNCTION
CLOSE
GRAPHIC
EQUALIZER
OPEN CLOSE
VOLUME
REMOTE SENSOR
REPEAT
PREVIOUS
NEXT
PLAY PAUSE
PROG
STOP
A
PLAY
B
RECORD PLAY
CASSETTE CONTROL CD CONTROL BUILT IN MIC
TOP AND FRONT PANEL
VOLUME
– to adjust the volume.
GRAPHIC EQUALIZER
– three band graphic equalizer to adjust the tone.
FUNCTION – CD: to switch to CD mode/power ON.
– TAPE: to switch to TAPE mode/power OFF.
– RADIO: to switch to RADIO mode/power ON.
FM MODE / RECORD MODE – to switch to FM STEREO or FM MONO mode.
– to switch to the desired dubbing mode:
– HIGH SPEED DUBBING
– NORMAL REC
– MIC. REC.
p
– connection for headphones (impedance 8-32 ohms).
OPEN/CLOSE – to open the CD door.
BAND – to select between FM, MW, and LW waveband.
FM STEREO 6 – lights up when receiving FM stereo stations.
TUNING – to tune to a radio station.
DIAL SCALE
BUILT-IN MIC – microphone under the speaker grill.
CD PLAYER
PLAYING A CD
Selecting another track during play
• Press PREVIOUS ∞ or NEXT § until the
required track number appears in the display.
– The selected track begins to play.
Starting with a particular track
• Press PREVIOUS ∞ or NEXT § until the
required track number appears in the display.
• Press PLAY/PAUSE 2;.
– Play starts from the selected track.
Searching for a passage during play
• Hold PREVIOUS ∞ down to search
backwards to the beginning.
• Hold NEXT § down to search forwards to the
end.
The searching speed is determined by how long
a key is pressed:
– the first two seconds fairly slowly, with sound;
– then at maximum speed, with no sound.
Repeating a track
REP 1
• Press REPEAT before or during play.
– REP 1 lights up; the track will now be repeated
continuously.
• Press REPEAT twice to stop the track being
repeated.
Repeating the CD
• Press REPEAT twice before or during play. REP
– REP lights up; the CD will now be repeated
continuously.
• Press REPEAT again to stop the CD being
repeated.
CONTROLS
BAND
CASSETTE CONTROL
FM STEREO 6
Controls deck A
TUNING
PAUSE ;
– to interrupt playback.
DIAL SCALE STOP/EJECT 9// – to stop and eject the cassette.
F.FWD 5
– fast forward.
REW 6
– fast rewind.
PLAY 1
– to start cassette playback.
Controls deck B
PAUSE ;
– to interrupt playback/recording.
STOP/EJECT 9// – to stop and eject the cassette.
F.FWD 5 – fast forward.
REW 6 – fast rewind.
PLAY 1
– to start cassette playback.
REC/CD SYNCHRO – to start recording.
CD CONTROL
PLAY/PAUSE 2; – to start and interrupt playback.
STOP 9 – to stop playback.
REPEAT – to repeat one/all tracks.
PREVIOUS ∞ / NEXT § – to skip and search
backward/forward.
PROG.
– to program track numbers in the
memory.
CD DISPLAY
REP 1
PGM
Track number: PLAY
; : PAUSE
PGM: programming
REP 1: repeat one
REP: repeat all
ER: error
PROGRAMMING
By programming the player you can play up to
20 tracks in any desired order. If you exceed the
maximum of 20 tracks, the program function will
start again from the beginning.
Storing a program
• In STOP mode, press PROG..
The display will show PGM and __.
PGM
• Select the first desired track using PREVIOUS
∞ or NEXT §.
• Store this track by pressing PROG. again.
• Select and store in this way all desired titles.
Checking the program
• In STOP mode, press PROG. repeatedly.
– The display shows in sequence all
programmed track numbers.
– Then, PGM __ appears again.
• Press PROG. one more time.
– The display will show the first track of the
program again.
Playing a program
• Press PLAY/PAUSE 2;.
– Play starts with the first track of the program.
PGM
– After the last track playback stops.
– The display shows the first track of the
program.
Note:
• Press STOP 9 to stop playback.
• While playing a program, it is possible to use
PREVIOUS ∞ or NEXT § to select the
desired programmed tracks.
Erasing a program
• Press STOP 9 twice or press OPEN/CLOSE
straight away.
– The program has now been erased.
CD PLAYER
CD HANDLING
• Use only Digital Audio CDs which have the
symbol .
• To take the CD out of its box easily, press the
centre spindle while lifting the CD.
2
1
• Never write on a CD or attach any sticker to
the CD.
• Always hold the CD at the edge and always
store it in its box after use with the label facing
up.
• To remove dust and dirt, breathe on the CD
and wipe it with a soft, lint-free cloth in a
straight line from the center towards the edge.
Cleaning agents may damage the CD.
• Do not expose the CD to rain, moisture, sand,
or to excessive heat. (E.g. from heating
equipment or in motor cars parked in the sun.)
INSERTING A CD
• Set the FUNCTION switch to CD.
• Press OPEN/CLOSE to open the CD door.
• Insert the AUDIO CD, printed side facing up.
• Close the cover.
– The CD-player scans the contents list of the CD
After that, the total number of tracks appears
on the display.
CASSETTE DECK
Recording from the CD-player DUBBING - Copying from deck A to B
(CD synchro recording)
When dubbing it is recommended to use fresh
• Set the FUNCTION switch to CD.
batteries or to connect the set to the AC power
supply.
• It's not necessary to start the CD player se-
parately: by pressing REC./CD SYNCHRO the
• Set the FUNCTION switch to TAPE
CD player starts automatically.
• Set the RECORD MODE switch to:
– If the CD player is in STOP position, recording
– NORMAL REC: for normal speed copying;
will start from the beginning of the CD (or from
– HIGH SPEED DUBBING: for high speed
the beginning of the programmed selection).
copying.
• To start a recording in the middle of a track,
Do not use this switch during dubbing.
play the CD in the normal way.
• Press both STOP/EJECT 9//
• Start recording by pressing REC./CD
SYNCHRO as soon as the desired passage is
buttons and insert a
reached. recorded cassette into
deck A and a cassette
Recording from the radio
which is suited for
• Set the FUNCTION selector to RADIO.
recording into deck B.
• Select the wave band using the BAND switch.
• Press PAUSE ; followed by REC./CD SYNCHRO
on deck B.
• Tune to desired radio station using the
TUNING control knob. • To start dubbing, press PLAY 1 on deck A.
• In case of FM radio recordings, set the FM
• Press PAUSE ; on deck B if you wish to omit
MODE switch to the desired position.
undesired passages.
• If during the recording of an MW/LW station,
– Playback of deck A continues.
a whistling sound is heard, this sound can be
• Press PAUSE ; again to restart dubbing.
suppressed by setting the BEAT CANCEL switch
to another position. • If, during dubbing, you press PAUSE ; on
deck A, a blank part will be recorded on the
Mono recording from the built-in microphone
cassette in deck B.
• Set the FUNCTION switch to TAPE
• Press both STOP/EJECT 9// buttons if you
• Set the RECORD MODE switch to MIC. REC
wish to stop dubbing.
position.
– The set is then switched off.
• Set the VOLUME control to the minimum
volume level (during microphone recording ,
monitoring is not possible).
PLAYING A CD
• Press PLAY/PAUSE 2; to start playback.
– The display shows the track number.
• Adjust the sound using the VOLUME control.
• Set the tone color with the 3-band GRAPHIC
EQUALIZER.
• For brief interruptions, press PLAY/PAUSE 2;.
– ; is shown on the display.
• To resume playback, press PLAY/PAUSE 2;
again.
• To stop playback, press STOP 9.
– The total number of tracks will then appear on
the display.
– The CD player also goes to position STOP:
– by pressing OPEN/CLOSE;
– when the end of the CD is reached;
– if the batteries run down or if the power sup-
ply is interrupted.
• To take out the CD, open the CD door by
pressing OPEN/CLOSE.
• Open the CD door only if the CD-player is in
position STOP.
REMOTE CONTROL
(only RR 3500 CD)
PLAY 2 – to start CD playback
STOP 9 – to stop CD playback
NEXT ™ – to select the next CD track
PREV ¡ – to select the previous CD track
VOLUME –/+ – to adjust the volume