Operation; Connecting The Power Supply; Normal Playback - Marantz SA-11S1 User Manual

OPERATION

* In this instruction manual, some operations can only be performed with the remote control. For
operations that can be performed with buttons both on the main unit and on the remote control, the
button names are shown in the mark. And for operations that can only be performed with
buttons on the remote control, the button names are shown in the

CONNECTING THE POWER SUPPLY

1
Plug the power cable into AC IN jack on the back
panel.
A
C
IN
2
Turn on the power switch of the audio unit
(amplifier, etc.) that is connected with this unit.
Set the selector on the connected unit to this unit.
3
Plug the power cable into an AC outlet.

NORMAL PLAYBACK

SUPER AUDIO CD PLAYER PLAYBACK
SUPER AUDIO CD PLAYER SA-11S1
OPEN/
CLOSE PLAY
DISPLAY OFF
STOP
SOUND POWER ON/OFF
MODE
PAUSE
M A G H
,
mark.
q Press POWER switch to turn on.
LCD
The display cycles from TOC Reading → No
Disc (when no disc is loaded) → Super Audio
CD (when the start sound mode setting is Super
Audio CD).
w Press the
button
OPEN/CLOSE
The disc tray comes out. Place the disc with label
side up on the tray.
To play a single (8cm) CD, place the disc with
the indentation at the center of the tray.
e Press
button.
OPEN/CLOSE
r Press
button.
PLAY
Disc type is automatically detected and playback
is started. Track number and track elapsed
time(minute, second) appear on the display.
* For Super Audio CD/CD hybrid-layer discs (See
page 2), the layer that is set in the start sound
mode (See page 10) is played. To change the
layer, use the button. (See page
SOUND MODE
9)
(Exp.:Track 6, Elapsed time 2 min 8 sec)
Number of current track Minutes Seconds
Remaining track numbers
Playback automatically stops at the end of the
final track.
To start playback form the first track
Press button.
PLAY
To stop playback
Press button.
STOP
To eject disc
Press button to open the disc tray
OPEN/CLOSE
and take the disc off. Press the button again to close
the tray.
Disc tray must be closed when the unit is not be
used.
To pause playback
Press button.
PAUSE
PAUSE indicator will light and playback is paused at
the point that the button is pressed. To restart
playback, press button again or press
PAUSE
button.
PLAY
To change time display
Press the button on the remote control.
TIME
Each time button is pressed, display will
TIME
change in the following order. "Track elapsed time"
→ "Track remaining time" → "Total remaining time"
→ "Track elapsed time".
• Track remaining time
(The remaining playing time from the playing
point to the end of the current track)
"REMAIN"
"–" is displayed is displayed
• Total remaining time
(The remaining playing time from the playing
point to the end of the last track)
"TOTAL REMAIN"
"–" is displayed is displayed
* If button is pressed when Super Audio CD
TIME
disc that supports text is in use, time display is given
priority and the text information will not be displayed
afterward. To see the text information, press
TEXT
button.
SWITCHING SOUND MODE (SUPER AUDIO CD)
SUPER AUDIO CD PLAYER SA-11S1
OPEN/
CLOSE PLAY
DISPLAY OFF
STOP
SOUND POWER ON/OFF
MODE
PAUSE
Button
SOUND MODE
q Press
SOUND MODE button in stop mode
(not playing).
The currently selected layer or area is shown on
the LCD. (CD or Super Audio CD)
If SOUND MODE button is pressed again, a
playable layer or area will be shown, and the layer
or area will be switched to new one.
* When layer or area is switched, TOC will be
read again.
* The sound mode cannot be changed for Audio
CDs and discs with only a Super Audio CD
area.
* The sound mode on hybrid layer discs will be
changed in the following order.
Super Audio CD stereo area → CD layer →
Super Audio CD stereo area
* Sound mode can be selected while the tray is
open. Select a desired layer or area and press
button then the tray will close and
PLAY
playback will be started.
w Press the
button during
SOUND MODE
playback.
The currently selected layer or area is shown on
the LCD. (CD or Super Audio CD)
If SOUND MODE button is pressed again, the
playback is stopped, and the layer or area will
be switched to new one.
When you want to listen at that area, press
button again. The playback will be
PLAY
started.
9