Hilti SFC 14-A Operating Instructions Manual
Hide thumbs
Also See for SFC 14-A:
- Operating instructions manual (240 pages) ,
- Manual (184 pages) ,
- Original operating instructions (176 pages)
Related Manuals for Hilti SFC 14-A
Summary of Contents for Hilti SFC 14-A
- Page 1 SFC 14-A / SFC 18-A Operating instructions Mode d’emploi Manual de instrucciones Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...
- Page 2 Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...
- Page 3 Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...
- Page 4 Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...
- Page 5 Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...
- Page 6 ETL listed to US and Canadian safety standards Homologué ETL (conforme aux normes de sécurité américaines et canadiennes) Producto homologado según normas de seguridad americanas y canadienses Produto homologado de accordo com as normas de segurança americanas e canadianas Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...
-
Page 7: Table Of Contents
These numbers refer to the illustrations. You can find the illustrations at the beginning of the operating instructions. In these operating instructions, the designation “power tool” always refers to the SFC 18-A or SFC 14-A cordless drill / driver with battery fitted. Product overview Keyless chuck... -
Page 8: General Information
Belt hook (optional) Release buttons with additional function (charge status display acti- § vation) Charge status and fault display (Li-ion battery) 1 General information 1.1 Safety notices and their meaning DANGER Draws attention to imminent danger that will lead to serious bodily injury or fatality. -
Page 9: Safety Instructions
Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Type: Generation: 01 Serial no.:... - Page 10 2.1.1 Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Page 11 pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Page 12 2.1.5 Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- Page 13 d) Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers during breaks between working. e) Avoid touching rotating parts. Switch the power tool on only after bringing it into position at the workpiece. Touching rotating parts, especially rotating insert tools, may lead to injury.
-
Page 14: Description
Do not use the battery as a power source for other unspecified appliances. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. The power tool is designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. - Page 15 1 Power tool 1 Operating instructions NOTE Approved accessories are available from your Hilti Center or can be ordered online at www.hilti.com. 3.3 Additional items required for operating the tool The suitable, recommended B12/2.6 LiIon battery and the C 4⁄1250 charger.
-
Page 16: Technical Data
switch, the power tool may not restart immediately when the switch is pressed again (while the power tool is cooling down). 4 Technical data Right of technical changes reserved. Power tool SFC 14A SFC 18A Rated voltage (DC 14.4 V 21.6 V voltage) Weight of power tool... -
Page 17: Before Use
Before fitting the battery, check that the power tool is switched off and that the safety lock is engaged (forward/reverse switch in the middle position). Use only the Hilti batteries approved for use with this power tool. Check that the battery is securely seated in the tool. -
Page 18: Operation
Pull the battery out of the locked position (working position) and move it into the first latching position (transport position). Observe national and international transport regulations when shipping batteries (transportation by road, rail, sea or air). 5.5 Belt hook CAUTION Check that the belt hook is fitted securely before beginning work. - Page 19 6.2 Speed selection using the 2-speed gear switch WARNING Large and heavy insert tools must only be operated in first gear. There is otherwise a risk that the tool will be damaged when it is switched off or, under unfavorable conditions, the chuck might be detached. NOTE The mechanical 2-speed gear switch can be used to select the speed range required.
-
Page 20: Care And Maintenance
3. Check that the bit adapter is held securely (check by pulling). 4. Fit the bit in the bit holder. 6.7.2 Screwdriving 1. Select the torque function on the setting ring for torque and drilling. 2. Set the forward / reverse switch to the desired direction of rotation. 6.7.3 Removing the bit / bit holder 1. -
Page 21: Troubleshooting
– Charge the batteries using the specified and approved Hilti battery chargers for Liion batteries. 8 Troubleshooting Fault Possible cause Remedy The power tool does- The battery is The battery must be n’t run. discharged or is not heard to engage with pushed all the way in. -
Page 22: Disposal
Batteries that have reached the end of their life must be disposed of in accordance with national regulations or returned to Hilti. Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. - Page 23 Hilti Corporation LI-9494 Schaan Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan Pos. 3 | 20150415 Printed: 20.05.2015 | Doc-Nr: PUB / 5071590 / 000 / 02...