Related Manuals for Hilti DD-REC 1
Summary of Contents for Hilti DD-REC 1
- Page 1 DD-REC 1 Bedienungsanleitung Operating instructions Mode d’emploi Brugsanvisning Käyttöohje Bruksanvisning Printed: 07.07.2013 | Doc-Nr: PUB / 5139951 / 000 / 00...
- Page 2 DD EC-1 Printed: 07.07.2013 | Doc-Nr: PUB / 5139951 / 000 / 00...
- Page 3 DD EC-1 Printed: 07.07.2013 | Doc-Nr: PUB / 5139951 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5139951 / 000 / 00...
-
Page 5: Table Of Contents
DD-REC1 water recycling system General information It is essential that the operating instructions are read before the In these operating instructions, this symbol indi- cates points of particular importance to safety. The unit is used for the first time. instructions at these points must always be observed in order to avoid a risk of serious injury. -
Page 6: Technical Data
Technical data Nominal power input: 300 W Nominal voltage: ✱ 100 V 110 V 120 V 220 V 230 V 240 V Mains frequency: 50–60 Hz Weight of unit (without water): 25 kg Water volume: 4–13 l Max. number of holes per filling: ✱✱ Approx. -
Page 7: Accessories
Wear suitable working clothing. Wear shoes with non-slip soles. Use the correct accessories. Use only the recommended original Hilti accessories. Make the working area safe. Objects which could cause injury should be removed Use the unit only for the purposes for which it is intended. -
Page 8: Before Use
220–230 V 50 m 80 m the unit or supply cord repaired at a Hilti service centre. Never expose the plug connections for the unit to water. If a plug interface has become wet, always disconnect the supply cord plug from the mains socket before touch- ing it and wiping it dry. - Page 9 – Check the inner and outer cover seals for damage. on the diamond core drilling machine and begin drilling Carefully remove dirt from the surfaces of the seals. (please refer to the operating instructions for the DD Ensure that the main filter is seated securely. Check EC-1 diamond core drilling machine).
- Page 10 – Rinse out the remaining slurry and, if necessary, to access the storage location and insert a spare filter. remove dried-on remains. Wipe the inside of the sight Insert the grip section of the spare main filter in the glass with a soft cloth. Clean the surfaces of the seals holder in the base of the housing at an angle and then on the container carefully .
-
Page 11: Care And Maintenance
Manufacturer's warranty – tools engage the catch and, at the same time, lift the unit away from the wheel assembly. Hilti warrants that the tool supplied is free of defects – When using the wheel assembly, care must be in material and workmanship. This warranty is valid so... -
Page 12: Disposal
Disposal Return waste material for recycling Most of the materials from which Hilti electric tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling. -
Page 13: Troubleshooting
The cord should be checked and replaced if necessary by an electrical specialist. Unit defective The unit should be repaired at a Hilti service centre. Acoustic warning signal Core bit or diamond core drilling Check for free flow and eliminate... -
Page 14: Declaration Of Conformity (Original)
We declare, under our sole responsibility, that this pro duct complies with the following directives and standards: EN 60 335-1, EN ISO 12100, 2011/65/EU, 2006/95/EC, 2004/108/EC. Hilti Corporation, Feldkircherstrasse 100, FL-9494 Schaan Paolo Luccini Johannes W. Huber Head of BA Quality and Process Management Senior Vice President BA Electric Tools &... - Page 15 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2527 | 0213 | 00-Pos. 5 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 337354 / Printed: 07.07.2013 | Doc-Nr: PUB / 5139951 / 000 / 00...