Advertisement
Quick Links
A
A
A
A
Overall length
No
load speed
(RPMl
B
Net weight
Spindle thread
MODEL 9040L
INSTRUCTION MANUAL
DOUBLE
INSULATION
6,000
I
470
mm
(18-1/2")
I
4.8
kg
(10.6 Ibsl
I
5/8"-11
UNC
*
Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS
FOR
FUTURE REFERENCE.
Advertisement
Related Manuals for Makita ANGLE SANDER 9040L
Summary of Contents for Makita ANGLE SANDER 9040L
- Page 1 INSTRUCTION MANUAL load speed (RPMl 6,000 Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS Overall length Net weight (18-1/2") FUTURE REFERENCE.
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. - Page 3 11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
-
Page 4: Specific Safety Rules
Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. - Page 5 The followings show the symbols used for tool. SYMBOLS volts herts kilograms seconds alternating current direct current alternating or direct current Class II Construction splash-proof construction watertight construction revolutions or reciprocation per minute of blow number...
- Page 6 Always be sure that the tool is switched off and unplugged before installing or removing the disc. NOTE: Use sander accessories specified in this manual. These must be purchased by separate. Mount the rubber pad onto the spindle. Fit the disc on over the rubber pad and screw the lock nut onto the spindle.
- Page 7 tighten lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the installation procedure in reverse. IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual.
- Page 8 Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle.
- Page 9 Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 1 5 O to the workpiece surface.
-
Page 10: Maintenance
SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Insulating tip Carbon brush... - Page 11 ACCESSORIES CAUTION : These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use any other accessories The accessories or attachments should be used only in the proper and intended manner.
- Page 12 @Rubber pad Part No. 743012 @Sanding lock nut 48 (For abrasive disc) Part No. 224517-1 @Wire cup brush . - I Part No. 743206-A 743206-8 @Urethane washer 14 Part 261039-0 When using wire brush, mount urethane washer 14 to the spindle. It will make wire brush.
- Page 13 May-13--'98 ANGLE SANDER Model 9040L Note: The switch, noise suppressor and other part configurations may differ from country country.
- Page 14 Retaining Ring R-40 Ball h a r i n g 6203DDW Bearing Spindle Rubber Pad 170 Sanding Lock Nut 14-48 Tapping Screw CT 5x16 Makita Mark Brush Holder Cap A C. Carbon Brush Name Mate Handle (With Item 421 Cord Guard...
- Page 15 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date original purchase.