Advertisement
Quick Links
Cordless Ratchet Wrench
7.2 V
With
318''
Square Drive Socket Adapter
MODEL 6912D
MODEL
6912DW
With Fast Charger
1
Hr.
A.C. only 50 Hz
-
60
Hz
D.C. 7.2 V
INSTRUCTION MANUAL
SPECIFICATIONS
7
IRPMI
1
Tightening torque
Overall length
Net weight
No load speed
Capacities
Bolt size
12
mm
(112'')
I
400
I
38 kg
.
cm
12.7 f t
.
Ibsl
I
322
mm
I12-11/16"1
I
0.85 kg 11.9
Ibsl
Battery Cartridge 7000
I
Model DC7100 Fast Charger
Voltage
I
Charging time
I
Input
I
output
Advertisement
Related Manuals for Makita 6912D
Summary of Contents for Makita 6912D
- Page 1 7.2 V Square Drive Socket Adapter 318’’ Tightening torque 38 kg 12.7 f t Ibsl Model DC7100 Fast Charger Input A.C. only 50 Hz MODEL 6912D 6912DW MODEL With Fast Charger Overall length Net weight I12-11/16”1 0.85 kg 11.9 Ibsl output...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger o n switch. Be sure switch is 16.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord Do not operate charger with damaged cord or plug mediately. not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way; take 1 1 .
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Always cover the battery terminals cartridge is not used. - Page 6 Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out plate on the tool andgrasp both sides of the cartridge while withdrawing it from the barrel. Do not use force when inserting the battery cartridge.
- Page 7 Installing socket adapter When you wish t o use a smaller size socket, install the socket adapter. To install it, insert the socket adapter into the socket in the tool, making sure that the tightening direction matches the arrow on the tool.
- Page 8 2. Final manual tightening operation After turning the tool off, perform the final manual tightening operation by pulling on the tool grip in the same tightening direction. The maximum size that can be tightened with this tool 1/2" (socket size: 13/16'). Refer t o the table for the correct tightening torque and check the torque with a torque wrench.
-
Page 9: Maintenance
Always be sure that the tool is switched off and attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. battery cartridge... - Page 10 ACCESS0 R I ES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk The accessories or attachments should be used only in the proper and intended manner.
- Page 11 June-26-'86 CORDLESS RATCHET WRENCH Model 69120 Note: The s w i t c h and o t h e r part configurations may differ f r o m c o u n t r y t o country.
- Page 12 MAKflA L I M I T E D ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of origjnal purchase.