D-Link DCS-4701E User Manual
Vigilance hd outdoor poe mini bullet camera
Hide thumbs
Also See for DCS-4701E:
- Quick installation manual (101 pages) ,
- User manual (78 pages) ,
- Quick installation manual (20 pages)
Related Manuals for D-Link DCS-4701E
Summary of Contents for D-Link DCS-4701E
-
Page 1: User Manual
Version 1.00 | 04/21/2015 User Manual Vigilance HD Outdoor PoE Mini Bullet Camera DCS-4701E... -
Page 2: Manual Revisions
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change. -
Page 3: Table Of Contents
Using the Configuration Interface ........17 Help..................55 Live Video ................19 Technical Specifications ............56 Setup ..................21 Setup Wizard ..............21 Network Setup ..............26 Dynamic DNS ..............29 Image Setup ..............30 Video ...................32 Preset ...................34 Motion Detection ............36 Time and Date ..............37 Event Setup ...............38 D-Link DCS-4701E User Manual... -
Page 4: Product Overview
Section 1: Product Overview Product Overview Package Contents DCS-4701E Vigilance HD Outdoor PoE Mini Bullet Camera Cable Waterproofing Connector Rubber Power Connector Plug Mounting Kit CD-ROM with User Manual and software Quick Installation Guide If any of the above items are missing, please contact your reseller. -
Page 5: Introduction
The DCS-4701E has an IP66 certified weatherproof housing designed for both indoor and outdoor applications. The built-in removable IR-cut filter and IR LEDs give the DCS-4701E the capability to view up to 30M at night. The DCS-4701E also incorporates Power over Ethernet (PoE), allowing it to be easily installed in a variety of locations without the need for supplemental power cabling. -
Page 6: Features
Advanced Event Management The DCS-4701E can be set up to send e-mail notifications with snapshots when an event occurs, such as when motion is detected. Events can be triggered from several sources, such as motion detection and time based events. -
Page 7: Hardware Overview
Can be attached to a grounding wire if desired Reset Button Press and hold for 10 seconds to reset camera back to the factory default settings Adjustment Ring Loosen to adjust camera angle and tighten to lock camera angle D-Link DCS-4701E User Manual... -
Page 8: Sides
Section 1: Product Overview Sides RJ-45 connector for Ethernet, can also be used to power the camera using Ethernet Jack Power over Ethernet (PoE) Power Connector Connects to an optional 12 V / 1.5 A power adapter (not included) D-Link DCS-4701E User Manual... -
Page 9: Mounting The Camera
Step 2 Use the screws provided to mount the camera to the wall. If you are running the camera cables out the side of the camera, guide the camera cables through the cable channel on the base. D-Link DCS-4701E User Manual... - Page 10 When you are finished, turn the adjustment ring clockwise to tighten it. If you need to waterproof your installation, please continue to the next page. D-Link DCS-4701E User Manual...
-
Page 11: Waterproofing Your Installation
Step 1 Place the washer around the base of the Ethernet connector as shown. Step 2 Thread bare Ethernet cable through the waterproof connector as shown, then crimp an RJ-45 plug onto the cable. D-Link DCS-4701E User Manual... - Page 12 Screw the back part of the waterproof connector clockwise until there is a tight seal around the Ethernet cable. If you are using PoE to power your camera, use the included rubber power connector plug to the power connector. D-Link DCS-4701E User Manual...
- Page 13 Section 2: Assembly and Installation If you are using a power adapter(not included) to power your camera, wind waterproof tape around the connection in an overlapping manner to cover it. D-Link DCS-4701E User Manual...
-
Page 14: Software Installation
Insert the DCS-4701E CD into your computer's CD-ROM drive to begin the installation. If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click the Start button and type D:\autorun.exe (where D: represents the drive letter of your CD-ROM drive) and press Enter. - Page 15 Admin ID is admin with the password left blank. Click the checkboxes if you wish to change the admin ID and password for the camera, and enter the new ID and password you wish to use. Click Next to continue. D-Link DCS-4701E User Manual...
- Page 16 Select Static IP if you want to manually enter the IP settings for the camera. Click Next to continue. Step 6 Take a moment to confirm your settings and click Restart. D-Link DCS-4701E User Manual...
-
Page 17: Configuration
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web configuration utility is designed to allow you to easily access and configure your DCS-4701E. At the end of the wizard, click Link, or enter the IP address of your camera into a web browser, such as Mozilla Firefox. - Page 18 Enter admin as the default username and leave the password blank. Click OK to continue. Step 4 This section displays your camera’s live video. You can select your video profile and view or operate the camera. D-Link DCS-4701E User Manual...
-
Page 19: Live Video
Auto Pan Starts the automatic panning function. The ROI will pan from back and forth within the FOV. Stop Stops the camera ePTZ motion. Preset Path Starts the camera's motion along the predefined path. D-Link DCS-4701E User Manual... - Page 20 Set a Storage Folder Video Profile 3 Full screen mode Take a Snapshot Go To: If any presets have been defined, you can select them here to move the (Preset List) camera to the selected preset. D-Link DCS-4701E User Manual...
-
Page 21: Setup
To quickly configure your Network Camera’s motion detection settings, click Motion Detection Setup Wizard. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to"Motion Detection" on page 36. D-Link DCS-4701E User Manual... -
Page 22: Internet Connection Setup Wizard
Section 3: Configuration Internet Connection Setup Wizard This wizard will guide you through a step-by-step process to configure your new D-Link Camera and connect the camera to the internet. Click Next to continue. Select how the camera will connect to the Internet. - Page 23 If you have selected DHCP, you will see a summary of your settings, including the camera's IP address. Please write down all of this information as you will need it in order to access your camera. Click Apply to save your settings. D-Link DCS-4701E User Manual...
-
Page 24: Motion Detection Setup Wizard
Refer to "Motion Detection" on page 36 for information about how to configure motion detection. Step 2 This step allows you to enable motion detection based on a customized schedule. Specify the day and hours. You may also choose to always record whenever motion is detected. D-Link DCS-4701E User Manual... - Page 25 Click Next to continue. Step 4 You have completed the Motion Detection Wizard. Please verify your settings and click Apply to save them. Please wait a few moments while the camera saves your settings and restarts. D-Link DCS-4701E User Manual...
-
Page 26: Network Setup
Invalid gateway settings may cause the failure of transmissions to a different subnet. Primary DNS: The primary domain name server translates names to IP addresses. Secondary DNS: The secondary DNS acts as a backup to the primary DNS. D-Link DCS-4701E User Manual... - Page 27 For instance, live1.sdp can be accessed at rtsp://x.x.x.x/video1.sdp where the x.x.x.x represents the IP address of your camera. Enable CoS: Enabling the Class of Service setting implements a best-effort policy without making any bandwidth reservations. D-Link DCS-4701E User Manual...
- Page 28 DNS. Enable Multicast for stream: The DCS-4701E allows you to multicast each of the available streams via group address and specify the TTL value for each stream. Enter the port and TTL settings you wish to use if you do not want to use the defaults.
-
Page 29: Dynamic Dns
DDNS account. Password: Enter the password used to connect to your DDNS server account. Timeout: Enter the DNS timeout values you wish to use. Status: Indicates the connection status, which is automatically determined by the system. D-Link DCS-4701E User Manual... -
Page 30: Image Setup
Select the frequency used by your power lines to avoid interference or distortion. White Balance: Use the drop-down box to change white balance settings to help balance colors for different environments. You can choose from Auto, Outdoor, Indoor, Fluorescent, and Push Hold. D-Link DCS-4701E User Manual... - Page 31 3D filtering reduces the amount of image noise when viewing a low-light environment. Higher levels of 3D filtering will apply stronger levels of noise reduction. Reset Default: Click this button to reset the image to factory default settings. D-Link DCS-4701E User Manual...
-
Page 32: Video
Lower frame rates will result in stuttering motion, and requires less bandwidth. Video Quality: This limits the maximum frame rate, which can be combined with the "Fixed quality" option to optimize D-Link DCS-4701E User Manual... - Page 33 The bps will affect the bit rate of the video recorded by the camera. Higher bit rates result in higher video quality. Fixed quality: Select the image quality level for the camera to try to maintain. High quality levels will result in increased bit rates. D-Link DCS-4701E User Manual...
-
Page 34: Preset
Clicking the Remove button will delete the currently selected preset. Preset Sequence: This section allows you to create a preset sequence, which automatically moves the camera's view between a set of preset views. D-Link DCS-4701E User Manual... - Page 35 Clicking the trash can button will remove the currently selected preset from the sequence. If you want to change the dwell time for a preset, select it from the list, enter a new dwell time, then click the Update button. D-Link DCS-4701E User Manual...
-
Page 36: Motion Detection
Right click on the camera image to bring up the following menu options: Select All: Draws a motion detection area over the entire screen. Clear All: Clears any motion detection areas that have been drawn. Restore: Restores the previously specified motion detection areas. D-Link DCS-4701E User Manual... -
Page 37: Time And Date
NTP server. NTP Server: Network Time Protocol (NTP) synchronizes the DCS-4701E with an Internet time server. Choose the one that is closest to your location. Set the Date and Time Manually: This option allows you to set the time and date manually. -
Page 38: Event Setup
Event Setup In a typical application, when motion is detected, the DCS-4701E sends images to a FTP server or via e-mail as notifications. As shown in the illustration below, an event can be triggered by many sources, such as motion detection. When an event is triggered, a specified action will be performed. -
Page 39: Add Server
Enter the unique name of your server. E-mail: Enter the configuration for the target e-mail server account. FTP: Enter the configuration for the target FTP server account. Network Storage: Specify a network storage device. Only one network storage device is supported. D-Link DCS-4701E User Manual... -
Page 40: Add Media
1 pic. 2 pic. 3 pic. 4 pic. 5 pic. 6 pic. 7 pic. 8 pic. 9 pic. The moment the trigger is activated. File name prefix: The prefix name will be added to the file name. D-Link DCS-4701E User Manual... - Page 41 This is the prefix that will be added to the filename of saved video clips. System log: Select this option to set the media type to system logs. This will save the event to the camera system log, but will not record any snapshots or video. D-Link DCS-4701E User Manual...
-
Page 42: Add Event
Action: If you have created Server and Media entries, you will see them appear here. Select which Server you want to send to and which Media you want the camera to send. D-Link DCS-4701E User Manual... -
Page 43: Add Recording
Please note that if the free HDD space is not enough, the recording will stop. Before you set up this option please make sure your HDD has enough space, and it is better to not save other files in the same folder as recording files. D-Link DCS-4701E User Manual... - Page 44 Time of each file for recording: If this is selected, files will be separated based on the maximum length you specify. File Name Prefix: The prefix name will be added on the file name of the recording file(s). D-Link DCS-4701E User Manual...
-
Page 45: Advanced
The IR light will always be on. Sync with ICR: The IR light will turn on when the ICR filter is disabled (night mode). Schedule: The IR light will turn on or off according to the schedule that you specify below. D-Link DCS-4701E User Manual... -
Page 46: Https
ƒ Create a certificate request and install Status: Displays the status of the certificate. Note: The certificate cannot be removed while HTTPS is still enabled. To remove the certificate, you must first uncheck Enable HTTPS secure connection. D-Link DCS-4701E User Manual... -
Page 47: Access List
Section 3: Configuration Access List Here you can set access permissions for users to view your DCS-4701E. Allow list: The list of IP addresses that have access rights to the camera. Note: When adding entries to the Allow list, make sure the first entry includes the IP address of the computer or device you are using to access the camera. -
Page 48: Snmp
Enter the authentication password used for your read/ write SNMP server. Encryption Password: Enter the encryption password used for your read/write SNMP server. Read Only Security Name Enter a name for the read-only community of your read- only SNMP server. D-Link DCS-4701E User Manual... - Page 49 Enter the type of authentication used by your read-only SNMP server. Authentication Password: Enter the authentication password used for your read- only SNMP server. Encryption Password: Enter the encryption password used for your read-only SNMP server. D-Link DCS-4701E User Manual...
-
Page 50: Maintenance
Enter a label for the camera, which will be shown on the OSD when it is enabled. Show Time: Select this option to enable the time-stamp display on the video screen. LED: You may specify whether or not to illuminate the status LED on the camera. D-Link DCS-4701E User Manual... -
Page 51: System
This will restart your camera. Enable Schedule Reboot: If you want your camera to reboot on a regular schedule, check the Enable Schedule Reboot checkbox, then select the days and time you want the camera to reboot D-Link DCS-4701E User Manual... -
Page 52: Firmware Upgrade
Section 3: Configuration Firmware Upgrade The camera's current firmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available firmware version. To upgrade the firmware on your DCS-4701E, please download and save the latest firmware version from the D-Link Support Page to your local hard drive. -
Page 53: Status
Section 3: Configuration Status Device Info This page displays detailed information about your device and network connection. D-Link DCS-4701E User Manual... -
Page 54: Logs
Section 3: Configuration Logs This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to delete the saved log information. D-Link DCS-4701E User Manual... -
Page 55: Help
Section 3: Configuration Help This page provides helpful information regarding camera operation. D-Link DCS-4701E User Manual... -
Page 56: Technical Specifications
ƒ QoS ƒ DNS client ƒ CoS ƒ DDNS client (D-Link) ƒ Multicast ƒ SMTP client ƒ IGMP ƒ FTP client ƒ ONVIF compliant Security Administrator and user group protection HTTP and RTSP authentication Password authentication D-Link DCS-4701E User Manual... - Page 57 Power Consumption 4.7 watts ± 5% Temperature Operating: -30 to 50 °C (-22 to 122 °F) Storage: -20° to 70° C (-4° to 158° F) Humidity Operating: 20% to 80% non-condensing Storage: 5% to 95% non-condensing Certifications CE LVD C-Tick D-Link DCS-4701E User Manual...
- Page 58 Appendix A: Technical Specifications Dimensions 98.1 66.6 164.7 D-Link DCS-4701E User Manual...