Table of Contents
Advertisement
Instillation Requirement
Use of Adapter Plug
Because of potential safety huzards
recommend against use of tin adapter
use an adapter, where local codes
permit, a TEMPORARY
CONNECTION may be made to a
properly grounded two-prong wall
outlet by use of a UL listed adapter
(Fig. 2) tivailablc at nlost ]octi]
hardware stores.
TEMPORARY METHOD
. : . 0 {~~"
ALIGN LARGE
PRONGS/SLOT
I
INSURE PROPER GROUND
AND FIRM CONNECTION
BEFORE USE
The larger slot in the adapter must be
aligned with the larger slot in the
wall outlet to provide proper polarity
in the connection of the power cord,
CAUTION: Attaching tin adapter
screw does not ground an appliance
unless cover screw is metal, and not
insulated, and wall outlet is
grounded throllgh house wiring.
the outlet is properly grounded.
When disconnecting the power
cord from the adapter, always
hold the adtipter with one hand,
If this is not done, the adapter
break with repetited use.
Should the adapter ground
terminal break, DO NOT USE the
appliance until a proper ground
has again been established.
Use of Extension Cords
Because of potentiui safety hazards
under cert~in conditions, we
strongly recommend against the
use of an extension cord, However,
cord, it is absolutely necessary that
it be a UL 1 isted 3-w ire grounding
type appliance extension cord
having a grounding type plug and
outlet and that the electrical rating
(minimum) and 120 volts.
The refrigerator should always
be plugged into its own
individual electrical outlet—
( 115 volt, 60 Hertz, or 100 volt, 50
Hertz, single phase AC). This is
recommended for best performance
and to prevent overloading house
wiring circuits, which could cause a
Refrigerator Location
Do not install refrigerator where
temperature will go below 60°F.
"
because it will not run often enough
to maintain proper temperatures.
Do install it on a floor strong
enough to support it fully loaded.
regarding location,
Clearances
Allow the following clearances for
ease of installation, proper air
circulation, and plumbing and
electrical connections:
Sides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . %"
Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0"
Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1"
Refrigerator Side . . . . . . . . . . . . . . . . . . . . . 1 M"
Freezer Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I X"
Water Supply to Icemaker
You will need to connect your
water supply kit containing copper
tubing, shu-off valve, fittings and
instructions is available at extra cost
from your dealer. There should be
sufficient tubing for the icemaker
moving the refrigerator out from the
wall several feet (approximately 8
1 ()-inch diameter coils).
Rollers
Adjustable rollers behind the base
grille enable you to move your
refrigerator away from the wall for
cleaning. These rollers should be set
so the refrigerator rests firmly on the
floor. To assure that the doors will
open position, the;e is a built-in tilt
from the front to the back of the
cabinet. Side-by-side refrigerators
hinges that lift both doors slightly
when opened, allowing the force of
gravity to help close them securely.
To adjust rollers, remove the base
and pulling it out.
Turn the roller adjusting screws
clockwise to raise the refrigerator,
counterclockwise to lower it. Use
head bolt) or pliers.
When adjusting front rollers for
proper door closure, we recommend
the bottom front edge of the cabinet
be approximately 5/8" from the floor.
To replace base grille, align prongs
on back of grille with clamps in
cabinet and push forward until
Advertisement
Table of Contents
