Reset Procedure - Sunfire TGR-3 User Manual

APPENDIX
"Protect" shows in the display
The TGR-3 has thermal and
short-circuit protection circuits. If the
amplifi er internal temperature is high,
a quiet fan will engage and start to
cool things down. If the temperature
increases further, the TGR-3 will go
into a standby mode and "Protect" will
appear in the display. When it cools,
the TGR-3 will turn back on.
If the TGR-3 goes into protect mode
often, check the following:
• Each speaker's average imped-
ance is not less than 4 ohms.
• The TGR-3 has good ventilation,
none of its vents are covered.
• Try setting all the speakers to
Small, and let your subwoofers
handle the heavy bass.
• Check that the amplifi er power
output is a good match for your
speakers. If your speakers are
ineffi cient, consider using an exter-
nal power amplifi er.

Reset procedure

The TGR-3 is a microprocessor
controlled device of great complexity.
Occasional power fl uctuations and
spikes may cause the TGR-3 to "lock
up" or act strangely. Often times a
software problem may be resolved
by completely powering off the unit,
waiting 30 seconds and then plugging
the unit back in. Try this method fi rst
before using the Full Reset procedure
described below as follows:
Warning: the TGR-3 will be re-
set to the factory defaults, and
will clear all memory. All your
stored OSD settings and Tuner
presets will be erased.
• On page 57, write down your
calibration settings, input settings,
Tuner presets, and any other set-
tings you have made.
• Press the power button to turn the
unit off, or turn it off from the wall
for a moment.
• Press and continue to hold down
the front panel Power button and
the Tone DOWN button at the
54
same time.
• The TGR-3 will power on and cycle
through the display. Keep holding
the buttons down until "Resetting
to Factory Defaults" appears in the
front panel display
• When the TGR-3 has been reset, it
will shut off.
• Turn the TGR-3 back on and it will
go to the default screen. It has now
been reset.
• If the TGR-3 has to be reset regu-
larly, you should invest in a good
quality AC line conditioner.
Updating fi rmware problems
• See page 51
• If you have a Palm Pilot™ or simi-
lar device with "HotSync™" or its
equivalent, you may need to dis-
able this software before proceed-
ing. This software 'seizes' control
of a serial port on your machine
and prevents the Sunfi re software
from accessing that port. Use an-
other port or disable HotSync.
• Check that the serial cable is con-
nected correctly between the TGR-
3 and your computer's serial port.
A Hum is heard in your speak ers
This problem is more than likely
caused by a "ground loop" in your sys-
tem, rather than a fault in the TGR-3.
Follow these steps to isolate the main
cause of the hum, there may even be
more than one.
• Remember to turn off all compo-
nents in your system, including the
TGR-3, before disconnecting or
con nect ing any cables.
• Disconnect the following items in
order, and check each time if the
hum has gone away:
• Disconnect all cables which come
from outside the room, such as
cable TV, satellite TV, or roof top
antennas. Make sure that they are
dis con nect ed where they fi rst enter
the room, so they are making no
con nec tion to the TGR-3 or the TV,
or any other component. If the hum
is caused by the cable TV line,
then you will need a "ground loop
iso la tor." This is an inexpensive
device fi tted in line with the coaxial
cable feed. Con tact your ca ble
com pa ny or your Sun fi re Dealer for
as sis tance.
• Disconnect all connections from
the TGR-3 to your TV.
• Disconnect any component which
has a grounded power cord.
• If the hum persists, disconnect all
the source com po nents one at a
time from the back of the TGR-3,
until you identify the prob lem.
• Ground loop isolators are available
for audio lines and video. Ask your
Sunfi re Dealer for assistance.
• Try moving the speaker cables
away from any power cords. Try
just one speaker, connecting it to
different channels and see if an
amplifi er channel is bad.
• If you are still having a problem,
Sunfi re's dealers and technical
support staff will assist you.
Other causes of noise
• Speaker noise may also be caused
by in ter fer ence or noise on your
AC line. Make sure there are no
large ap pli anc es sharing the line,
or halogen lamps or light-dimming
Triac devices.
• Try connecting your system to an-
other AC socket on a sep a rate line.
• If the hum is heard from within the
TGR-3 and not through the speak-
ers, this may also be caused by
in ter fer ence on the AC or DC lines.
The power trans form ers may turn
this interference into an audible
noise. Internal hum can be made
worse by a shelf or cabinet reso-
nating, so try moving the TGR-3 to
another shelf.
• Try moving your components further
away from the TV, es pe cial ly if
you ever notice the screen has
changed color in the area closest
to the component.
• If you have very high effi ciency
speak ers, these may show up
noise which other speakers may
not.
User's Manual