Table of Contents
Advertisement
H
OOKING
C
OMBINATION
UHF/VHF
A
NTENNA
A
combination antenna
receives normal broadcast
channels (VHF 2-13 and UHF
14-69). Your connection is easy
since there is only one 75Ω
(ohm) antenna jack on the
back of your TV - and that's
where the antenna goes.
S
UHF/VHF
EPARATE
Y
ou may have two separate
antennas. One antenna is
for VHF channels (2-13) and
the other antenna is for UHF
channels (14-69).
For homes with separate
UHF/VHF antennas, you will
need an optional combiner
before you can connect the
antennas to the TV.
VCR C
ONNECTIONS
T
he basic Antenna/Cable to
VCR to TV connection is
shown here. If you have a Cable
Box, refer to the VCR owner's
manual for details.
300 to 75Ω Adaptor
Outdoor
VHF/UHF
Antenna
Cable TV signal
C
TV
ABLE
Y
our Cable TV signal may be
a single (75Ω) cable or a
Cable Box installation. In either
case, the connection to the TV
is very easy.
Cable TV
Company
Cable TV Signal (75Ω)
Cable Box
U
Y
TV (A
P
OUR
If your antenna has a
round connector (75Ω),
then you're ready to connect it
to the TV.
If your antenna has flat
twin-lead wire (300Ω), you
first need to attach the antenna
wires to the screws on a 300
to 75Ω adaptor.
Combination
VHF/UHF
Antenna
(Outdoor or
Indoor)
Attach the separate
UHF and VHF antennas to
the correct screws on the
combiner.
Outdoor UHF Antenna
(Twin-lead 300Ω)
Twin-lead
Outdoor VHF
Antenna
(Twin-lead 300Ω)
OR
Outdoor VHF
Antenna
(Round cable 75Ω)
Connect your
Antenna or Cable signal to
the IN FROM ANT(enna)
jack on the VCR.
Coaxial cable
OUT TO TV
IN FROM ANT.
VCR
If you do not have a
Cable Box, then you're ready
to connect your Cable TV signal
to the TV.
If you have a Cable Box:
Connect the Cable TV signal to
the IN jack on the Cable Box.
OR
Coaxial cable
/C
NTENNA
ABLE
Push the round end of
the adaptor (or cable) onto
the ANT(enna) IN jack on
the back of the TV. If the
round end of the adaptor or
cable is threaded, screw it
down tight.
Twin-lead
Wire
OR
Round Cable
75Ω
Push the round end of the
combiner onto the ANT(enna)
IN jack on the back of the TV.
Round
End
Wire
U H
F
3 0 0
‰
75-300Ω
V H F
Adaptor
U/V
Combiner
Connect a coaxial
cable to the OUT TO
TV jack on the VCR
and to the ANT(enna)
IN jack on the TV.
The coaxial cable may be
supplied with the VCR.
ANT.IN
ANT.IN
Back of TV
If you do not have a Cable Box, connect the
Cable TV signal directly to the ANT(enna) IN jack on the
TV.
If you have a Cable Box:
Use a coaxial cable to connect the OUT jack of the Cable
Box to the ANT(enna) IN jack on the TV.
NOTE: The coaxial cable might be supplied by the Cable
TV company.
ANT.IN
ANT.IN
Back of TV
- 2 -
C
)
ONNECTIONS
300 to 75Ω
Adaptor
ANT.IN
ANT.IN
Back of TV
ANT.IN
ANT.IN
Back of TV
Refer to the VCR
owner's manual for other
possible connections and for
operating details.
Note to the Cable TV System Installer:
This reminder is provided to call the Cable TV
system installer's attention to Article 820-40 of
the National Electrical Code, which provides
guidelines for proper grounding - in particular,
specifying that the cable ground shall be con-
nected to the grounding system of the building,
as close to the point of cable entry as possible.
S
MART
H
ELP
To set the
TV to select only
the channel num-
bers in your area,
see Auto Install on
page 4.
S
MART
H
ELP
To order
any optional
accessory, contact
your dealer. Or,
call 1-800-851-8885
and refer to the fol-
lowing part num-
bers to order.
• UHF/VHF
Combiner:
4835 466 97016
• 75-300Ω
Adaptor:
M61009
• 300-75Ω
Adaptor:
4835 218 27003
S
MART
H
ELP
To select
only the channels on
your Cable system,
see Auto Install
(page 4).
If you use a Cable
Box, set the TV to
the same channel as
the CH 3/4 switch
on the back of the
Cable Box and
select channels at
the Cable Box.
Advertisement
Table of Contents
