Stanley FatMax FME720 User Manual
Hide thumbs
Also See for FatMax FME720:
- Original instructions manual (125 pages) ,
- Manual (145 pages) ,
- Manual (33 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Stanley FatMax FME720
Summary of Contents for Stanley FatMax FME720
- Page 1 FME720...
- Page 4 33.9° 31.6°...
-
Page 6: Intended Use
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) Your Stanley Fat Max sliding compound mitre saw has been protected supply. Use of an RCD reduces the risk of designed for sawing wood, plastic and non-ferrous metal only. - Page 7 Repairs to the laser should be carried out by Do not use blades of larger or smaller diameter than authorised repair agents or Stanley Fat Max service staff. recommended. For the proper blade rating refer to the Disconnect the machine form the mains before carrying technical data.
-
Page 8: Residual Risks
Call Stanley Fat Max customer services for you nearest they have been given supervision or instruction concern- service agent. -
Page 9: Electrical Safety
Inspect tool corsds periodically. If the supply cord is damaged, it must be replaced by the manufacturer or an Wear safety glasses or goggles. authorised Stanley Fat Max Service Centre in order to avoid a hazard. Wear ear protection. Voltage drops Inrush currents cause short-time voltage drops. - Page 10 ENGLISH (Original instructions) Features Mitre angle adjustment The sliding compound mitre saw scale can be easily read This tool includes some or all of the following features. showing mitre angles from 0° to 47° to the left and the right. 1.
- Page 11 (Original instructions) ENGLISH Hold the main operating handle (2) and pull the carriage (29) forward until the centre of the saw blade is over the Place your hands no closer than 150 mm from the blade. front of the workpiece. Hold the workpiece tightly to the table and the fence when Operate the on/off switch (3) and press the saw arm cutting.
-
Page 12: Bevel Cut
ENGLISH (Original instructions) Base moulding cut Adjust the fence to be as close to the blade as practical to provide maximum work piece support, without interfering Base moulding can be cut vertical against the fence or flat on with the up and down movement of the arm. the table. - Page 13 (Original instructions) ENGLISH Crown moulding cut (fig. L) Carrying the tool (fig. N) Crown moulding can only be cut flat on the table with this Loosen the mitre detent lever (11) (fig. B) and turn the mitre saw. table all the way to the right. Lock the table at the 45° This mitre saw has special mitre stops on 31.6°...
-
Page 14: Maintenance
(52) until the blade is secure. Should you find one day that your Stanley Fat Max product Replace the metal upper guard (26) into its original posi- needs replacement, or if it is of no further use to you, do not tion and tighten the two screws (50 and 51). -
Page 15: Technical Data
Stanley Europe provides a facility for the collection and (sound pressure) 95 dB(A), Uncertainty (K) 3 dB(A) recycling of Stanley Fat Max products once they have reached the end of their working life. To take advantage of this service (sound power) 108 dB(A), Uncertainty (K) 3 dB(A) please return your product to any authorised repair agent who will collect them on our behalf. - Page 16 If you wish to make a claim, contact your seller or check the location of your nearest authorised Stanley Fat Max repair agent in the Stanley Fat Max catalogue or contact your local Stanley office at the address indicated in this manual. A list of authorised Stanley Fat Max repair agents and full details of our after sales service is available on the internet at: www.
- Page 20 United Kingdom Stanley Fat Max Tel. 01753 511234 210 Bath Road Fax 01753 572112 Slough, Berkshire SL1 3YD www.stanleytools.co.uk 90607808 REV-0 02/2014...