Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EnGenius EnStation2
Summary of Contents for EnGenius EnStation2
-
Page 2: Table Of Contents
ABLE OF ONTENTS ABLE OF ONTENTS Conventions 0-vii Copyright 0-ix Product Overview Package Contents......................1-1 Product Overview......................1-2 Key Features ......................1-2 Benefits ........................... 1-3 Technical Specifications .................... 1-4 Wireless Specifications..................... 1-4 Hardware Specifications.................... 1-4 Software Specifications .................... 1-4 Product Interface...................... - Page 3 ABLE OF ONTENTS Installing the Device......................2-2 Pre-Installation Guidelines ..................2-2 Installing the Device ....................2-2 Wall Mounting the Device ..................2-3 Pole Mounting the Device ..................2-4 Web Configuration Logging In........................3-1 Best Practices ......................3-2 Basic Network Settings System Status........................
- Page 4 ABLE OF ONTENTS Viewing the WDS Link List..................... 4-8 System Setup........................ 4-9 Configuring Operation Modes..................4-9 Configuring IP Settings....................4-10 Configuring Spanning Tree Settings................4-11 Router Setup........................ 4-12 Configuring WAN Settings.................... 4-12 Static IP ........................ 4-12 Dynamic IP ......................4-13 Point-to-Point Protocol over Ethernet (PPPoE) .............
- Page 5 ABLE OF ONTENTS Client Router Mode ....................4-28 Configuring Wireless Security..................4-30 Wired Equivalent Privacy (WEP) ................4-30 Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) ............4-31 Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK) ..........4-32 Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed ..........4-33 Wi-Fi Protected Access (WPA) ...................
- Page 6 ABLE OF ONTENTS Configuring System Time.................... 4-47 Configuring Wi-Fi Schedule..................4-48 Add a Schedule Service ................... 4-48 Schedule Services Table ..................4-49 Configuring Command Line Interface................4-50 Configuring Logging....................4-51 Configuring Diagnostics....................4-52 Viewing Device Discovery.................... 4-53 Configure Denial of Service Protection................4-54 Logging Out.......................
- Page 7 ABLE OF ONTENTS Appendix A Federal Communication Commission Interference Statement..........A-1 Appendix B Europe – EU Declaration of Conformity................B-1 Appendix C World Wide Technical Support................... C-1...
- Page 8 ONVENTIONS Conventions The following conventions are used to give the user additional Example: information about specific procedures or content. It is important Indicates information used to demonstrate or explain an to pay attention to these conventions as they provide informa- associated concept.
- Page 9 ONVENTIONS Typographical Conventions The following typographical conventions are used in this docu- ment: Italics Indicates book titles, directory names, file names, path names, and program/process names. Constant width Indicates computer output shown on a computer screen, includ- ing menus, prompts, responses to input, and error messages. Constant width bold Indicates commands lines as entered on the computer.
- Page 10 OPYRIGHT Copyright This user guide and its content is copyright of © EnGenius Net- works, 2014. All rights reserved. Any redistribution or reproduction in part or in whole in any form is prohibited. Do not distribute, transmit, store in any form of electronic retrieval system or commercially exploit the content without the expressed written permission of EnGenius Networks.
-
Page 11: Product Overview
Product Overview Chapter 1... -
Page 12: Package Contents
RODUCT VERVIEW ACKAGE ONTENTS 1.1 Package Contents The EnStation2 package contains the following items: EnStation2 CPE PoE Injector with Power Adapter 24V PoE Injector Quick Installation Guide Mounting Screw Set Wall Mount Kit ... -
Page 13: Product Overview
RODUCT VERVIEW RODUCT VERVIEW 1.2 Product Overview Thank you for choosing EnStation2. The EnStation2 is a long Point-to-point and point-to-multipoint wireless range, high performance IEEE 802.11b/g/n network solution connectivity enable data transfers between two or more that provides Access Point, Client Bridge, WDS, and Client buildings Router functions in a single device. -
Page 14: Benefits
Wireless Extensions to Ethernet Networks WLANs enable network managers in dynamic environments to The EnStation2 is the ideal product around which you can build minimize overhead caused by moves, extensions to networks, your WLAN. The following list summarizes a few key and other changes. -
Page 15: Technical Specifications
RODUCT VERVIEW ECHNICAL PECIFICATION Technical Specifications Wireless Specifications IEEE802.11b/g/n, 300Mbps 2.400 to 2.484 GHz Hardware Specifications Physical Interface: 2 x 10/100Mbps LAN Ports, 1 x Reset Button Power Supply: Passive PoE, 24V/0.6A Power Adapter Dimension: D 190mm (7.48") x H 38mm (1.50") ... -
Page 16: Product Interface
RODUCT VERVIEW RODUCT NTERFACE 1.3 Product Interface BACK PANEL VIEW DESCRIPTION (Access Point or Client Bridge Mode) OFF=EnStation radio is off and the device is not sending or receiving data over the wireless LAN. ON=EnStation radio is on, and the device is WAN LED not sending or receiving data over the wireless LAN. -
Page 17: Installation
Installation Chapter 2... -
Page 18: System Requirements
NSTALLATION YSTEM EQUIREMENTS 2.1 System Requirements To install the EnStation2, you need the following: Computer (Windows, Linux, Mac OS X Operating System) Web Browser (Internet Explorer, FireFox, Chrome, Safari) Network Interface equipped: (one of the following) Wired connectivity: Network Interface with an open ... -
Page 19: Installing The Device
NSTALLING THE EVICE 2.2 Installing the Device Installing the Device Installing the EnStation2 on a pole or wall optimizes the wire- less access range. To install the EnStation2, use the following procedure to mount Note: the device on a pole and refer to the figure below: Only experienced installation professionals who are 1. -
Page 20: Wall Mounting The Device
EnStation2. Use a screwdriver to unlock the pole-mounting ring putting it through the EnStation2. 7. Mount the EnStation2 securely to the pole by locking the strap tightly. Figure 2-2: Wall Mounting the Device... -
Page 21: Pole Mounting The Device
NSTALLATION OUNTING THE EVICE Pole Mounting the Device A. Plug the dynamic stick into the bracket. B. Combine the sealing nut with the assembled kit. Tighten to secure together. C. Put the mock washer on the dynamic stick. D. Assemble the mounting kit with the CPE. E. -
Page 22: Web Configuration
Web Configuration Chapter 3... -
Page 23: Logging In
3.1 Logging In 3. When the login screen appears, enter admin for the user- The EnStation2 has a built-in Web Configurator that lets you name in the top field and admin for the password in the manage the unit from any location using a Web browser that bottom field. -
Page 24: Best Practices
Be sure you know how to restore it. Restoring an earlier working configuration can be useful if the EnStation2 becomes unstable or crashes. If you forget your password, you will have to reset the EnStation2 to its factory default settings and lose any customized override settings you configured. -
Page 25: Basic Network Settings
Basic Network Settings Chapter 4... -
Page 26: System Status
ASIC ETWORK ETTINGS YSTEM TATUS 4.1 System Status View the summary of the current system status including system (hardware/software version, date/time), wired network (LAN) and wireless network (WLAN) information. 4.1.1 Using Save/Reload Save and apply the settings shown in the Unsaved changes list, or cancel the unsaved changes and revert to the previous settings that were in effect. -
Page 27: Viewing The System Information
ASIC ETWORK ETTINGS IEWING YSTEM NFORMATION 4.1.2 Viewing System Information Displays status information about the current operating mode: System Information Shows the general system information such as operating modes, system up time, firmware version, serial number, kernel version, and application version. LAN Settings Shows Local Area Network settings such as the LAN IP address, Subnet Mask, and MAC address. - Page 28 LAN IP Address, Subnet Mask, Primary and Secondary DNS. Current Wireless Settings Shows wireless information such as frequency and channel. Since the EnStation2 supports multiple- SSIDs, information about each SSID, such as its ESSID and security settings, are displayed.
-
Page 29: Viewing The Wireless Client List
4.1.3 Viewing the Wireless Client List The Client List displays a list of clients associated to the EnStation2, along with the MAC addresses and signal strength for each client. To remove an SSID client from the list, click the button that appears in the Kick and Ban column. Click the Refresh button to... -
Page 30: Viewing The System Log
IEWING YSTEM 4.1.4 Viewing the System Log The EnStation2 automatically logs events to internal memory. Note: The oldest events are deleted from the log when memory is full. Click the Refresh button to update the Client List or the Clear button to remove all events. -
Page 31: Viewing The Connection Status
ASIC ETWORK ETTINGS IEWING ONNECTION TATUS 4.1.5 Viewing the Connection Status Displays the current status of the network. The WLAN information shown includes network type, SSID, BSSID, Connection Status, Wireless Mode, Current Channel, Security, Tx Data Rate, Current noise level, and Signal Strength. The WAN information shown includes the MAC address, connection type, connection status, IP address, IP subnet mask, primary DNS and secondary DNS. -
Page 32: Viewing The Dhcp Client Tables
4.1.6 Viewing the DHCP Client Table The DHCP Client table displays the clients that are associated to the EnStation2 through DHCP. The MAC addresses and signal strength for each client are also shown. Click the Refresh button to update the Client List. -
Page 33: Viewing The Wds Link List
4.1.7 Viewing the WDS Link List The WDS Link List displays the clients that are associated to the EnStation2 through WDS. The MAC addresses, link status and signal strength for each client are also shown. Click the Refresh button to update the Client List. -
Page 34: System Setup
ETUP 4.2 System Setup The following sections explain the features and functionality of the EnStation2 in access point mode, client bridge mode, WDS access point mode, WDS bridge mode, WDS station mode and client router mode. 4.2.1 Configuring Operation Mode Set the primary function of the device by choosing the operation mode. -
Page 35: Configuring Ip Settings
ONFIGURING ETTINGS 4.2.2 Configuring IP Settings From here you can configure the LAN settings for the EnStation2 using a static or dynamic IP address: IP Network Settings Configure the network connection type using either a static IP or dynamic IP. - Page 36 ETWORK ETTINGS ONFIGURING ETTINGS IPv6 Default Gateway Enter the IPv6 default gateway of the EnStation2. IPv6 Primary DNS Enter the IPv6 primary DNS of the EnStation2. IPv6 Secondary DNS Enter the IPv6 secondary DNS of the EnStation2. Click Apply to save the settings or Cancel to discard changes.
-
Page 37: Configuring Spanning Tree Settings
Enables or disables the EnStation2 Spanning Tree function. Bridge Hello Time Specifies Bridge Hello Time, in seconds. This value determines how often the EnStation2 sends hello packets to communicate information about the topology throughout the entire Bridged Local Area Network. -
Page 38: Router Setup
ETUP 4.3 Router Setup 4.3.1 Configuring WAN Settings Configure the WAN settings for the EnStation2 using a static or dynamic IP address, PPPoE or PPTP. Static IP Setting a static IP address allows an administrator to set a specific IP address for the router and guarantees that it can't be assigned a different address. - Page 39 Enter the secondary DNS server address. Discard Ping on WAN Check the box to enable pings to be recognized on the EnStation2 interface. Uncheck the box to disable the feature and block pings on the EnStation2 Wan interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid.
-
Page 40: Dynamic Ip
Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check the box to enable pings to be recognized on the EnStation2 interface. Uncheck the box to disable the feature and block pings on the EnStation2 Wan interface. -
Page 41: Point-To-Point Protocol Over Ethernet (Pppoe)
(PPP ASIC ETWORK ETTINGS OINT OINT ROTOCOL OVER THERNET Point-to-Point Protocol over Ethernet (PPPoE) Point-to-Point Protocol over Ethernet (PPPoE) is used mainly by ISPs that provide DSL modems to connect to the Internet. Enter the maximum transmission unit (MTU). The MTU specifies the largest packet size permitted for an Internet transmission (PPPoE default: 1492). - Page 42 Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check the box to enable pings to be recognized on the EnStation2 interface. Uncheck the box to disable the feature and block pings on the EnStation2 Wan interface.
-
Page 43: Point-To-Point Tunnelling Protocol (Pptp)
(PPTP) ASIC ETWORK ETTINGS OINT OINT UNNELLING ROTOCOL Point-to-Point Tunnelling Protocol (PPTP) The Point-to-Point Tunnelling Protocol (PPTP) is used in association with Virtual Private Networks (VPNs). There are two parts to a PPTP connection: the WAN interface settings and the PPTP settings. - Page 44 Connect on Demand If you want the EnStation2 to end the Internet connection after it has been inactive for a period of time, select this option and enter the number of minutes you want that period of inactivity to last.
-
Page 45: Configuring Lan Settings
Enter the LAN IP Subnet mask. WINS Server IP Enter the WINS Server IP. Use Router As DHCP Server Check this option to enable the EnStation2 internal DHCP server. Starting IP Address Specify the starting IP address range for the pool of allocated for private IP addresses. -
Page 46: Configuring Vpn Pass-Through
VPN P ASIC ETWORK ETTINGS ONFIGURING HROUGH 4.3.3 Configuring VPN Pass-Through VPN Pass-through allows a secure Virtual Private Network (VPN) connection between two computers. PPTP Pass through Check this option to enable PPTP Pass-through mode. L2TP Pass-through Check this option to enable L2TP Pass-through mode. IPSec Pass-through Check this option to enable IPSec Pass-through mode. -
Page 47: Configuring Port Forwarding
ASIC ETWORK ETTINGS ONFIGURING ORWARDING 4.3.4 Configuring Port Forwarding Port forwarding enables multiple server applications on a LAN to serve clients on a WAN over a single WAN IP address. The router accepts incoming client packets, filters them based on the destination WAN, or public port and protocol, and forwards the packets to the appropriate LAN, or local, port. - Page 48 ASIC ETWORK ETTINGS ONFIGURING ORWARDING Enable Click to enable or disable the forwarded port profile. Modify Click to modify the forwarded port profile. Delete Click to delete the forwarded port profile. Click Add Entry to add port forwarding rules. Click Accept to confirm the changes. Service Name Enter a name for the port forwarding rule.
-
Page 49: Configuring Demilitarized Zone
ASIC ETWORK ETTINGS ONFIGURING EMILITARIZED 4.3.5 Configuring Demilitarized Zone Configuring a device on the LAN as a Demilitarized Zone (DMZ) host allows unrestricted two-way Internet access for Internet applications, such as online video games, to run from behind the NAT firewall. The DMZ function allows the router to redirect all packets going to the WAN port IP address to a particular IP address on the LAN. -
Page 50: Configuring Wireless Lan
Incorrectly changing these settings may cause the device to stop functioning. Do not modify the settings in this section without a thorough understanding of the parameters. Access Point Mode The EnStation2 supports Access Point Mode. In this mode, users with a wireless client device within range can connect to the EnStation2 to access the WLAN. Wireless Mode Wireless mode supports 802.11b/ g/n mixed... - Page 51 ASIC ETWORK ETTINGS ONFIGURING IRELESS Auto Check this option to enable Auto Channel selection. AP Detection AP Detection can select the best channel to use by scanning nearby areas for Access Points. Current Profile Configure up to four different SSIDs. If many client devices will be accessing the network, you can arrange the devices into SSID groups.
-
Page 52: Client Bridge Mode
ASIC ETWORK ETTINGS LIENT RIDGE Client Bridge Mode Client Bridge Mode lets you connect two LAN segments via a wireless link as though they are on the same physical network. Since the computers are on the same subnet, broadcasts reach all machines. As a result, DHCP information generated by the server reaches all client computers as though the clients as residing on one physical network. - Page 53 ASIC ETWORK ETTINGS LIENT RIDGE Profile If you used the Site Survey, the Web Configurator will show nearby Access Points. To connect to an Access Point, click the Access Point’s BSSID. Wireless Security See Configuring Wireless Security. Click Refresh to scan again. 4-25...
-
Page 54: Wds Bridge Mode
WDS B ASIC ETWORK ETTINGS RIDGE WDS Bridge Mode Unlike traditional bridging, WDS Bridge Mode allows you to create large wireless networks by linking several wireless access points with WDS links. WDS is normally used in large, open areas where pulling wires is cost prohibitive, restricted or physically impossible. Wireless Mode Wireless mode supports 802.11b/g/n mixed modes. - Page 55 WDS B ASIC ETWORK ETTINGS RIDGE MAC Address Enter the MAC address of the Access Point to which you want to extend wireless connectivity. Mode Select Disable or Enable to disable or enable WDS. Click Accept to confirm the changes or Cancel to cancel and return to previous settings.
-
Page 56: Client Router Mode
In Client Router Mode, you can access the Internet wirelessly with the support of a WISP. In AP Router Mode, the EnStation2 can access the Internet via a cable or DSL modem. In this mode, the EnStation2 can be configured to turn off a wireless network name (SSID) broadcast, so that only stations that have the SSID can be connected. - Page 57 ASIC ETWORK ETTINGS LIENT OUTER Profile If you used the Site Survey, the Web Configurator shows nearby Access Points. To connect to an Access Point, click the Access Point’s BSSID. Wireless Security See Configuring Wireless Security. Click Refresh to scan again. 4-29...
-
Page 58: Configuring Wireless Security
IRELESS ECURITY 4.4.2 Configuring Wireless Security The Wireless Security Settings section lets you configure the EnStation2’s security modes: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. We strongly recommend you use WPA2-PSK. Wired Equivalent Privacy (WEP) Security Mode Select WEP from the drop-down list to begin the configuration. - Page 59 ASIC ETWORK ETTINGS ONFIGURING IRELESS ECURITY Note: 802.11n does not allow WEP/WPA-PSK TKIP/WPA2-PSK TKIP security modes. The connection mode will change from 802.11n to 802.11g. 4-30...
-
Page 60: Wi-Fi Protected Access Pre-Shared Key (Wpa-Psk)
(WPA-PSK) ASIC ETWORK ETTINGS ROTECTED CCESS HARED Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Security Mode Select WPA-PSK from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type: Both = uses TKIP and AES. ... -
Page 61: Wi-Fi Protected Access 2 Pre-Shared Key (Wpa2-Psk)
(WPA2-PSK) ASIC ETWORK ETTINGS ROTECTED CCESS HARED Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK) Security Mode Select WPA2-PSK from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type: Both = uses TKIP and AES. ... -
Page 62: Wi-Fi Protected Access Pre-Shared Key (Wpa-Psk) Mixed
(WPA-PSK) M ASIC ETWORK ETTINGS ROTECTED CCESS HARED IXED Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed Security Mode Select WPA2-PSK Mixed from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type: Both = uses TKIP and AES. ... -
Page 63: Wi-Fi Protected Access (Wpa)
(WPA) ASIC ETWORK ETTINGS ROTECTED CCESS Wi-Fi Protected Access (WPA) Security Mode Select WPA from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires pass- ... - Page 64 (WPA) ASIC ETWORK ETTINGS ROTECTED CCESS Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server. Interem Accounting Interval Specify the interem accounting interval (60 ~600 seconds). Click Save to save the changes or Cancel to cancel and return to previous settings. Note: 802.11n does not allow WEP/WPA-PSK TKIP/WPA2-PSK TKIP security modes.
-
Page 65: Wi-Fi Protected Access 2 (Wpa2)
2 (WPA2) ASIC ETWORK ETTINGS ROTECTED CCESS Wi-Fi Protected Access 2 (WPA2) Security Mode Select WPA2 from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES: ... - Page 66 2 (WPA2) ASIC ETWORK ETTINGS ROTECTED CCESS Radius Accounting Port Specify the port number that your RADIUS accounting server uses for authentication. The default port is 1813. Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server. Interem Accounting Interval Specify the internet accounting interval.
-
Page 67: Wi-Fi Protected Access (Wpa) Mixed
(WPA) M ASIC ETWORK ETTINGS ROTECTED CCESS IXED Wi-Fi Protected Access (WPA) Mixed Security Mode Select WPA Mixed from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type: Both = uses TKIP and AES. ... - Page 68 (WPA) M ASIC ETWORK ETTINGS ROTECTED CCESS IXED Radius Accounting Port Specify the port number that your RADIUS accounting server uses for authentication. The default port is 1813. Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server. Interem Accounting Interval Specify the interem accounting interval.
-
Page 69: Configuring Wireless Mac Filter
Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC addresses. You can manu- ally add a MAC address to restrict the permission to access EnStation2. The default setting is Disable Wireless MAC Filters. -
Page 70: Configuring Wds Link Settings
Click Accept to confirm the changes or Cancel to cancel and return to previous settings. Note: The Access Point to which you want to extend wireless connectivity must enter the EnStation2’s MAC address into its configuration. For more information, refer to the documentation for the Access Point. Not all Access Point support this feature. -
Page 71: Configuring Advanced Network Settings
ASIC ETWORK ETTINGS ONFIGURING DVANCED ETWORK ETTINGS 4.4.5 Configuring Advanced Network Settings Configure the advanced wireless settings for your access point using the screens in this section. Leave these settings as their default values if you are not sure what values to enter. Data Rate Select a data rate from the drop-down list. -
Page 72: Wireless Traffic Shaping
ASIC ETWORK ETTINGS ONFIGURING DVANCED ETWORK ETTINGS Wireless Traffic Shaping Enable Traffic Shaping Enable or disable the regulation of packet flow leaving an interface for improved QoS. Incoming Traffic Limit Specifies the wireless transmission speed used for downloading. Outgoing Traffic Limit Specifies the wireless transmission speed used for uploading. -
Page 73: Management Setup
4.5.1 Configuring Administrator Account Click the Administration link under the Management menu to change the user name and password used to log on to the EnStation2 Web Configurator. The default user name is admin and the default password is admin. Changing these settings protects the EnStation2 configuration settings from being accessed by unauthorized users. - Page 74 For example: If you specify the port number 8080, enter http://<IP address>:8080 to access the EnStation2 Web Configurator. Click Accept to apply the changes or Cancel to return to previous settings.
-
Page 75: Configuring Management Vlan
Click Accept to confirm the changes or Cancel to cancel and return previous settings. Note: If you reconfigure the Management VLAN ID, you may lose your connection to the EnStation2. Verify that the DHCP server supports the reconfigured VLAN ID and then reconnect to the EnStation2 using the new IP address. -
Page 76: Configuring Snmp
4.5.3 Configuring SNMP SNMP is used in network management systems to monitor network-attached devices for conditions that warrant administrative attention. SNMP Enable or disable the EnStation2 SNMP function. Contact Enter the contact details of the device. Location Enter the location of the device. - Page 77 SNMP ASIC ETWORK ETTINGS ONFIGURING User Name Specify the username for SNMPv3. Auth Protocol Select the authentication protocol type: MD5 or SHA. Auth Key (8-32 Characters) Specify the authentication key for authentication. Priv Protocol Select the privacy protocol type: DES. Priv Key (8-32 Characters) Specify the privacy key for privacy.
-
Page 78: Configuring Backup/Restore Settings
This feature is particularly convenient for administrators who have several EnStation2 devices that need to be configured with the same settings. This page also lets you return the EnStation2 to its factory default settings. -
Page 79: Configuring Auto Reboot Settings
ASIC ETWORK ETTINGS ONFIGURING EBOOT ETTINGS 4.5.5 Configuring Auto Reboot Settings Click the Auto Reboot Settings link under the Management menu to enable or disable the Auto Reboot function. This feature is particularly convenient to administrators for the scheduling of auto rebooting the device. This page also allows you to set the frequency of this function. -
Page 80: Configuring Firmware Upgrade
Upgrading firmware through a wireless connection is not recommended. Firmware upgrading must be performed while connected to an Ethernet (LAN port) with all other clients disconnected. The firmware upgrade procedure can take several minutes. Do not power off the EnStation2 during the firmware upgrade, as it can cause the device to crash or become unusable. -
Page 81: Configuring System Time
YSTEM 4.5.7 Configuring System Time Change the system time of the EnStation2 by manually entering the information, synchronizing the device with a PC, or setting up automatic updates through a network time (NTP) protocol server: Manually Set Date and Time... -
Page 82: Configuring Wi-Fi Schedule
ASIC ETWORK ETTINGS ONFIGURING CHEDULE 4.5.8 Configuring Wi-Fi Schedule Use the Wi-Fi schedule function to control the wireless power ON/OFF service that operates on a routine basis. Add a Schedule Service Create a schedule service type and date/time parameters for a specific service. Schedule Name Enter the description of the schedule service. -
Page 83: Schedule Services Table
EnStation2 to an NTP server, see Configuring System Time. Schedule Table Displays a list of scheduled services for the EnStation2. The properties of each service displayed are: Displays the ID number of the service in the table. Name Displays the description of the service. -
Page 84: Configuring Command Line Interface
4.5.9 Configuring Command Line Interface Most users will configure the EnStation2 through the graphical user interface (GUI). However, for those who prefer an alternative method there is the command line interface (CLI). The CLI can be access through a command console, modem or Telnet connection. -
Page 85: Configuring Logging
4.5.10 Configuring Logging The Log section displays a list of events that are triggered on the EnStation2 Ethernet and wireless interfaces. You can consult this log if an unknown error occurs on the system or when a report needs to be sent to the technical support department for debugging purposes. -
Page 86: Configuring Diagnostics
ASIC ETWORK ETTINGS ONFIGURING IAGNOSTICS 4.5.11 Configuring Diagnostics The Diagnosis feature allows the administrator to verify that another device is available on the network and is accepting request pack- ets. If the ping result returns alive, it means a device is online. This feature does not work if the target device is behind a firewall or has security software installed. - Page 87 Enter the interval for the speed test. Start Speed Test Click Start Speed Test to begin the speed test operation. IPv4 Port Displays the IPv4 port number of the EnStation2. IPv6 Port Displays the IPv6 port number of the EnStation2. 4-53...
-
Page 88: Viewing Device Discovery
ASIC ETWORK ETTINGS IEWING EVICE ISCOVERY 4.5.12 Viewing Device Discovery Device Name Displays the name of the devices connected to the network. Operation Mode Displays the operation mode of the devices connected to the network. IP Address Displays the IP address of the devices connected to the network. System MAC Address Displays the system MAC address of the devices connected to the network. -
Page 89: Configure Denial Of Service Protection
ASIC ETWORK ETTINGS ONFIGURE ENIAL OF ERVICE ROTECTION 4.5.13 Configure Denial of Service Protection Use TCP SYN Cookies Protection Click to enable TCP SYN cookies protection. SYN Flood Attack Protection Click to enable or disable SYN Flood Attack Protection. Match Interval Per Second Enter the allowed number of packets per second. -
Page 90: Logging Out
ASIC ETWORK ETTINGS OGGING 4.5.14 Logging Out Click Logout to logout from the EnStation2. 4-56... -
Page 91: Federal Communication Commission Interference Statement
PPENDIX EDERAL OMMUNICATION OMMISSION NTERFERENCE TATEMENT Appendix A Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 92 PPENDIX EDERAL OMMUNICATION OMMISSION NTERFERENCE TATEMENT Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 24cm between the radiator & your body.
-
Page 93: Europe – Eu Declaration Of Conformity
– EU D PPENDIX UROPE ECLARATION OF ONFORMITY Appendix B Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN60950-1 ... - Page 94 – EU D PPENDIX UROPE ECLARATION OF ONFORMITY Česk [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. [Czech] Dansk Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] [Danish] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
- Page 95 – EU D PPENDIX UROPE ECLARATION OF ONFORMITY Lietuvių Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas [Lithuanian] 1999/5/EB Direktyvos nuostatas. Nederlands Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met [Dutch] de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
-
Page 96: World Wide Technical Support
PPENDIX ORLD ECHNICAL UPPORT Appendix C WorldWide Technical Support REGION COUNTRY OF PURCHASE SERVICE CENTRE SERVICE INFORMATION CANADA web site www.engeniuscanada.com email rma@engeniuscanada.com Toll Free: (+1) 888-397-2788 Canada contact numbers Local: (+1) 905-940-8181 Monday - Friday hours of operation 9:00AM to 5:30PM EST (GMT-5) LOS ANGELES, USA web site www.engeniustech.com... - Page 97 DUBAI, UAE web site www.engenius-me.com Middle East email support@engenius- Russia CIS / Armenia, Azerbaijan, Belarus, me.com Georgia, Kazakhstan, Kyrgyzstan, Toll Free: U.A.E.: 800-EnGenius Moldova, Tajikistan, contact numbers 800-364-364-87 Turkmenistan, Ukraine, General: Uzbekistan (+971) 4357-5599 Turkey Afghanistan Sunday - Thursday Pakistan...
- Page 98 PPENDIX ORLD ECHNICAL UPPORT REGION COUNTRY OF PURCHASE SERVICE CENTRE SERVICE INFORMATION SINGAPORE web site www.engeniustech.com.sg/e_warranty_form Singapore, Cambodia, Indonesia, Malaysia, email techsupport@engeniustech.com.sg Thailand, Philippines, Vietnam Toll Free: contact numbers China, Hong Kong, Korea Singapore: 1800-364-3648 India Monday - Friday South Africa hours of operation 9:00 AM - 6:00 PM (GMT+8) Oceania...