Switching On And Off - Black & Decker FSS1600 Original Instructions Manual

Hide thumbs Also See for FSS1600:
Table of Contents

Advertisement

Available languages

Available languages

Detail tile cleaner
For cleaning grouted areas between tiles.
Large scrub brush cleaner with scraper
For cleaning heavily soiled object such as BBQ's.
Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
Attaching the hose and accessories (Fig. A & B)
Warning! Inspect the seal (7) on the steam nozzle (4) and
hose (8) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. A)
Press in the clips (9) on either side of the hose (8).
u
Press the hose (8) onto the steam nozzle (4) and release
u
the clips (9).
Important! Ensure that the hose (8) is securely fastened
before using the hand held steeam cleaner. If steam escapes
from the joint then the hose is not correctly fit, allow the unit to
cool then remove and re-fit the hose.
Attaching the variable steam jet nozzle (Fig. B)
Press in the clips (11) on either side of the variable steam
u
jet nozzle (12).
Press the variable steam jet nozzle onto the steam nozzle
u
(4) or the hose (8) and release the clips (11).
Important! Ensure that the variable steam jet nozzle (12) is
securely fastened before using the hand held steeam cleaner.
If steam escapes from the joint then the variable steam jet
nozzle is not correctly fit, allow the unit to cool then remove
and re-fit the variable steam jet nozzle.
Attaching other accessories (Fig. A)
Align the lugs on the hose (8) with the recesses on the
u
accessory.
Press the accessory (10) onto the hose (8) and twist anti-
u
clockwise untill the accessory clicks into place.
Note! The variable steam jet nozzle may be used without the
hose by fitting them directly to steam nozzle. All other acces-
sories must be connected to the hose for use.
(Original instructions)
Removing the hose and accessories(Fig. A & B)
Warning! The Steam nozzle, variable steam jet nozzle, hose
and accessories become hot during use. Allow the unit and all
accessories to cool before removing any accessories.
Removing an accessory (Fig. A)
Twist the accessory (10) clockwise then pull away from
u
the hose (8).
Removinging the hose (Fig. A)
Press in the clips (9) on either side of the hose (8) and pull
u
away from the steam nozzle (4).
Removing the variable steam jet nozzle (Fig. B)
Press in the clips (11) on either side of the vaiable steam
u
jet nozzle (12) and pull away from the steam nozzle (4).
Filling the water tank (Fig. C)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
Switch off the unit and disconnect from the mains supply.
u
Open the filler cap (6) by flipping it down.
u
Using the jug, fill the water tank (5) with water.
u
Warning! Your water tank has a 0.35 litre capacity.
Re-fit the filler cap (6).
u
Note: Ensure the filler cap is firmly secured.
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro fibre
pad fitted and a continuous run time of 90 seconds.

Switching on and off

To switch the appliance on, press the ON/OFF button (1).
u
It takes approximately 15 seconds for the hand held steam
cleaner to heat up.
Note: When the hand held steam cleaner is first turned on
the water reservoir will glow red. Once the hand held steam
cleaner is ready to use the water reservoir will glow blue.
Lift the lock off switch (2) and pull the trigger switch (3).
u
After a few seconds steam will be produced.
To switch the appliance off, release the trigger switch (3)
u
then press the ON/OFF button (1).
Caution! Always empty the hand held steam cleaner after
use.
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
ENGLISH
5

Advertisement

Table of Contents
loading

Table of Contents