Dodge 2014 urango Owner's Manual

Table of Contents

Quick Links

Download this manual

Durango

2 0 1 4

O W N E R ' S M A N U A L

Table of Contents

Chapters

Table of Contents

Summary of Contents for Dodge 2014 urango

Page 1 Durango 2 0 1 4 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of fea- With respect to any Vehicles Sold in Canada, the name Chrysler tures and equipment that are either standard or optional on Group LLC shall be deemed to be deleted and the name Chrysler this vehicle.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....8 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, Congratulations on selecting your new Chrysler Group particularly those used for braking, steering, transmis- LLC vehicle. Be assured that it represents precision sion, and transfer case shifting.
Page 7: Rollover Warning
INTRODUCTION 5 This Owner’s Manual has been prepared with the assis- ROLLOVER WARNING tance of service and engineering specialists to acquaint Utility vehicles have a significantly higher rollover rate you with the operation and maintenance of your vehicle. than other types of vehicles. This vehicle has a higher It is supplemented by Warranty Information, and various ground clearance and a higher center of gravity than customer-oriented documents.
Page 8: How To Use This Manual
6 INTRODUCTION two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
Page 9 INTRODUCTION 7...
Page 10: Warnings And Cautions
8 INTRODUCTION WARNINGS AND CAUTIONS vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment. This Owners Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle.
Page 11: Vehicle Modifications/Alterations
INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 13: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Rearming The System ....21 A WORD ABOUT YOUR KEYS ... . .14 ▫...
Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ General Information ....28 ▫ Power Liftgate — If Equipped ... . .48 REMOTE STARTING SYSTEM —...
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 ▫ Seat Belts And Pregnant Women ...68 ENGINE BREAK-IN RECOMMENDATIONS . . .113 ▫ Seat Belt Extender .....68 SAFETY TIPS .
Page 16: A Word About Your Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate Your vehicle uses a keyless ignition system. This system when in position. The three positions are OFF, ACC, and consists of a Key Fob with Remote Keyless Entry (RKE) ON/RUN.
Page 17: Key Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The emergency key is also for locking the glove box. You can keep the emergency key with you when valet parking. To remove the emergency key, slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand.
Page 18: Ignition Or Accessory On Message
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster. NOTE: With the Uconnect® system, the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to the OFF position.
Page 19: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! (Continued) CAUTION! • Allowing children to be in a vehicle unattended is An unlocked car is an invitation to thieves. Always dangerous for a number of reasons. A child or remove the Key Fob from vehicle, cycle the ignition others could be seriously or fatally injured.
Page 20: Replacement Keys
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle. The system will not allow the engine to crank CAUTION! if an invalid Key Fob is used to start and operate the • Do not make modifications or alterations to the vehicle.
Page 21: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: When having the Sentry Key® Immobilizer Sys- CAUTION! tem serviced, bring all vehicle keys with you to an • Always remove the Key Fobs from the vehicle and authorized dealer. lock all doors when leaving the vehicle unat- Customer Key Programming tended.
Page 22: Vehicle Security Alarm - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly approved NOTE: The Panic and Security alarms are quite different. by the party responsible for compliance could void the Please take a moment to activate the Panic and the user’s authority to operate the equipment.
Page 23: Rearming The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 2. Perform one of the following methods to lock the Rearming The System vehicle: If something triggers the alarm, and no action is taken to • Push LOCK on the interior power door lock switch disarm it, the Vehicle Security Alarm will turn off the with the driver and/or passenger door open.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cycle the vehicle ignition system out of the OFF • When the Vehicle Security Alarm is armed, the interior position. power door lock switches will not unlock the doors. • For vehicles equipped with Keyless Enter-N-Go™, The Vehicle Security Alarm is designed to protect your push the Keyless Enter-N-Go™...
Page 25: Tamper Alert
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Tamper Alert NOTE: • The front courtesy overhead console and door cour- If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times and the tesy lights do not turn on if the dimmer control is in exterior lights blink three times when you unlock the the Dome ON position (extreme top position).
Page 26: To Unlock The Doors And Liftgate
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Driving at speeds 5 mph (8 km/h) and above To Unlock The Doors And Liftgate disables the system from responding to all RKE transmit- Push and release the UNLOCK button on the RKE ter buttons for all RKE transmitters.
Page 27: To Lock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Flash Lamps With Lock To Lock The Doors And Liftgate This feature will cause the turn signal lights to flash when Push and release the LOCK button on the RKE transmit- the doors are locked or unlocked with the RKE transmit- ter to lock all doors and liftgate.
Page 28: Using The Panic Alarm
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • You may need to be less than 35 ft (11 m) from the Using The Panic Alarm vehicle when using the RKE transmitter to turn off the To turn the Panic Alarm feature on or off, push and hold Panic Alarm due to the radio frequency noises emitted the PANIC button on the RKE transmitter for at least one by the system.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Used batteries are harmful to the environment. You can dispose of them either in the correct containers as specified by law or by taking them to a Dealership, which will deal with their disposal. •...
Page 30: General Information
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE new battery with your fingers. Skin oils may cause If your RKE transmitter fails to operate from a normal battery deterioration. If you touch a battery, clean it distance, check for these two conditions: with rubbing alcohol.
Page 31: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • Hazard switch off NOTE: • The vehicle must be equipped with an automatic • Brake switch inactive (brake pedal not pushed) transmission to be equipped with Remote Start. • Ignition key removed from ignition switch •...
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted — Hood Ajar WARNING! • Remote Start Aborted — Liftgate Ajar • Do not start or run an engine in a closed garage or • Remote Start Aborted — Fuel Low confined area.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: To Exit Remote Start Mode Without Driving The Vehicle • If an engine fault is present or fuel level is low, the Push and release the REMOTE START button one time or vehicle will start and then shut down in 10 seconds.
Page 34: Door Locks
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: vented seat feature will automatically turn on when the remote start is activated. These features will stay on • For vehicles not equipped with the Keyless Enter-N- through the duration of remote start or until the ignition Go™...
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 upward. If the lock knob is down when the door is WARNING! closed, the door will lock. Therefore, make sure the key is • For personal security and safety in the event of an not inside the vehicle before closing the door.
Page 36: Power Door Locks
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks If you push the door lock switch while the ignition position is ACC or ON/RUN and the driver or front The power door lock switch is located on each front door passenger’s door is open, the doors will not lock.
Page 37: Child-Protection Door Lock System - Rear
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 stopped and in PARK. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further in- formation. Child-Protection Door Lock System — Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with Child-Protection Door Lock system.
Page 38: Keyless Enter-N-Go
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle. KEYLESS ENTER-N-GO™ The Passive Entry system is an enhancement to the vehicle’s Remote Keyless Entry (RKE) system and a feature of Keyless Enter-N-Go™.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • If the vehicle is unlocked by Passive Entry and no door goes ajar within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm. To Unlock From The Driver’s Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to unlock the driver’s door automatically.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock From The Passenger Side: If one of the vehicle doors is open and the door panel switch is used to lock the vehicle, once all open doors With a valid Passive Entry RKE transmitter within 5 ft have been closed the vehicle checks the inside and (1.5 m) of the passenger door handle, grab the front outside of the vehicle for any valid Passive Entry RKE...
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Unlock/Enter The Liftgate The liftgate passive entry unlock feature is built into the electronic liftgate handle. With a valid Passive Entry RKE transmitter within 3 ft (1.0 m) of the liftgate, push the electronic liftgate handle for a power open on vehicles equipped with Power Liftgate.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Liftgate With a valid Passive Entry RKE transmitter within 3 ft (1.0 m) of the liftgate, press the passive entry lock button located to the right of electronic liftgate handle. NOTE: If “Unlock All Doors 1st Press”...
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: • After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
Page 44: Windows
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON/RUN or ACCESSORY position.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Auto-Down Both the driver and front passenger window switches have an “Auto-Down” feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto-Down” move- ment, operate the switch in either the up or down direction and release the switch.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Up Feature With Anti-Pinch Protection — Driver And Front Passenger Door Only Lift the window switch fully upward to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: If the window runs into any obstacle during 1. Pull the window switch up to close the window Auto Up it will reverse direction and then go back down. completely and continue to hold the switch up for an Remove the obstacle and use the window switch again to additional two seconds after the window is closed.
Page 48: Wind Buffeting
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize the buffeting.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 NOTE: If “Unlock All Doors 1st Press is programmed in Uconnect® Settings, all doors will unlock when you press the button on the liftgate. If Unlock Driver Door 1st Press is programmed in Uconnect® Settings, the liftgate will unlock when you push the button on the liftgate For further information, refer to “Uconnect®...
Page 50: Power Liftgate - If Equipped
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may also be opened or closed by WARNING! pushing the LIFTGATE button located on the front overhead console, or closed by pushing the LIFTGATE Driving with the liftgate open can allow poisonous button located on left rear trim panel, near the liftgate exhaust gases into your vehicle.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: NOTE: • In the event of a power malfunction to the liftgate, an • The power liftgate buttons will not operate if the emergency liftgate latch release can be used to open vehicle is in gear or the vehicle speed is above 0 mph the liftgate.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate must be in the full open position for • If your liftgate is power closing and you put the rear liftgate close button on the left rear trim, near the vehicle in gear, the liftgate will continue to power liftgate opening to operate.
Page 53: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • An energy-absorbing steering column and steering OCCUPANT RESTRAINTS wheel Some of the most important safety features in your • Knee bolsters for front seat occupants vehicle are the restraint systems: • Three-point lap and shoulder belts for the driver and •...
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you will be carrying children too small for adult-sized WARNING! seat belts, the seat belts or the Lower Anchors and Tether • Never place a rear facing infant seat in front of an for CHildren (LATCH) feature also can be used to hold infant and child restraint systems.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 If a child from 2 to 12 years old (not in a rear facing child the Customer Center. Phone numbers are provided seat) must ride in the front passenger seat, move the seat under If You Need Assistance .
Page 56: Lap/Shoulder Belts
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and cause a collision that includes you. This can happen WARNING! (Continued) far away from home or on your own street. • Supplemental Side Air Bag Inflatable Curtain Research has shown that seat belts save lives, and they (SABIC) and Seat-Mounted Side Air Bags (SAB) can reduce the seriousness of injuries in a collision.
Page 57: Lap/Shoulder Belt Operating Instructions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or • Wearing a seat belt incorrectly is dangerous. Seat outside of a vehicle. In a collision, people riding in belts are designed to go around the large bones of these areas are more likely to be seriously injured your body.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Latch Plate Latch Plate To Buckle 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! WARNING! (Continued) • A belt that is worn under your arm is dangerous. • A belt that is buckled into the wrong buckle will Your body could strike the inside surfaces of the not protect you properly.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your 5. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap portion, pull up comfortable and not resting on your neck.
Page 61: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 6. To release the belt, push the red button on the buckle. 1. Position the latch plate as close as possible to the The belt will automatically retract to its stowed posi- anchor point.
Page 62: Seat Belts In Passenger Seating Positions
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into posi- tion.
Page 63: Automatic Locking Retractor Mode (Alr) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 to retract completely in this case and then carefully pull Driver Center Passenger out only the amount of webbing necessary to comfort- CRS Lock CRS Lock CRS Lock ably wrap around the occupant’s mid-section. Slide the First Row latch plate into the buckle until you hear a click.
Page 64: Energy Management Feature
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode WARNING! 1. Buckle the combination lap and shoulder belt. • The belt and retractor assembly must be replaced if 2. Grasp the shoulder portion and pull downward until the seat belt assembly Automatic Locking Retractor the entire belt is extracted.
Page 65: Seat Belt Pretensioners
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Seat Belt Pretensioners Supplemental Active Head Restraints (AHR) The seat belts for both front seating positions are These head restraints are passive, deployable compo- equipped with pretensioning devices that are designed to nents, and vehicles with this equipment cannot be readily remove slack from the seat belt in the event of a collision.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Review Table Below A — Downward Movement B — Rearward Movement C — Final Downward Movement To Engage Locking Mechanism 4.
Page 69: Enhanced Seat Belt Use Reminder System (Beltalert®)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer. Enhanced Seat Belt Use Reminder System (BeltAlert®) BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert®) to fasten their seat belts.
Page 70: Seat Belts And Pregnant Women
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Light remains illuminated until the respective seat belts NOTE: Although BeltAlert® has been deactivated, the are fastened. The driver should instruct all other occu- Seat Belt Reminder Light will continue to illuminate pants to fasten their seat belts.
Page 71: Supplemental Restraint System (Srs) - Air Bags
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 dealer can provide you with a seat belt extender. This Supplemental Restraint System (SRS) — Air Bags extender should be used only if the existing belt is not This vehicle has Advanced Front Air Bags for both the long enough.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Front Passenger Advanced Front Air Bags are certified to the new Federal regulations for Advanced Air Bags. The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • After any collision, the vehicle should be taken to an This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABIC) to protect the driver, front, authorized dealer immediately. and rear passengers sitting next to a window. The SABIC Air Bag System Components air bags are located above the side windows and their Your vehicle may be equipped with the following air bag...
Page 74: Advanced Front Air Bag Features
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Driver Side Knee Air Bag WARNING! • Front and Side Impact Sensors • No objects should be placed over or near the air • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, bag on the instrument panel, because any such and Seat Track Position Sensors objects could cause harm if the vehicle is in a...
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag Supplemental Seat-Mounted Side Air Bags (SAB) may deploys independently;...
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 windows, or area where the SAB or SABIC air bags WARNING! (Continued) inflate, even if they are in an infant or child restraint. • Do not use accessory seat covers or place objects Always sit upright as possible with your back against the between you and the SAB;...
Page 78: Air Bag Deployment Sensors And Controls
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Driver Knee Air Bag Advanced Front Air Bags and Supplemental Driver Side Knee Air Bag are designed to provide additional protec- The Supplemental Driver Side Knee Air Bag provides tion by supplementing the seat belts in certain frontal enhanced protection and works together with the Driver collisions depending on several factors, including the Advanced Front Air Bag during a frontal impact.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 The side air bags will not deploy in all side collisions. The ORC contains a backup power supply system that Side air bag deployment will depend on the severity and may deploy the air bags even if the battery loses power or type of collision.
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are possible, based on several factors, including the WARNING! collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel Ignoring the Air Bag Warning Light in your instru- separate and fold out of the way as the air bags inflate to ment panel could mean you won’t have the air bags their full size.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 The ORC determines if a side collision requires the side air bag, it signals the inflator units. A large quantity of air bags to inflate, based on the severity and type of non-toxic gas is generated to inflate the Supplemental collision.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE enough force to injure you if you are not belted and Enhanced Accident Response System seated properly, or if items are positioned in the area In the event of an impact causing air bag deployment, if where the SABIC inflates.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 In order to reset the Enhanced Accident Response System They are not permanent and normally heal quickly. functions after an event, the ignition switch must be However, if you haven’t healed significantly within a changed from IGN ON/RUN to IGN OFF.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Air Bag System WARNING! WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, • Modifications to any part of the air bag system seat belt pretensioners, and the front seat belt retrac- could cause it to fail when you need it.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Air Bag Warning Light WARNING! (Continued) • Do not attempt to modify any part of your air bag You will want to have the air bags ready to system. The air bag may inflate accidentally or may inflate for your protection in a collision.
Page 86: Event Data Recorder (Edr)
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • How various systems in your vehicle were operating; NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint • Whether or not the driver and passenger safety belts Controller (ORC) may also be disabled.
Page 87: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 To read data recorded by an EDR, special equipment is Children 12 years or younger should ride properly required, and access to the vehicle or the EDR is needed. buckled up in a rear seat, if available. According to crash In addition to the vehicle manufacturer, other parties, statistics, children are safer when properly restrained in such as law enforcement, that have the special equip-...
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WARNING! • For additional information, refer In a collision, an unrestrained child can become a www.seatcheck.org or call 1–866–SEATCHECK. Cana- projectile inside the vehicle. The force required to dian residents should refer to Transport Canada’s hold even an infant on your lap could become so website for additional information: great that you could not hold the child, no matter...
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Children who are two years old or Either an Infant Carrier or a Convertible Toddlers younger and who have not reached the Child Restraint, facing rearward in the rear...
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints reach the highest weight or height allowed by their convertible child seat. Safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until WARNING! they reach either the height or weight limit of their rear facing child safety seat.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 have outgrown the rear-facing weight or height limit of WARNING! their rear-facing convertible child seat. Children should • Improper installation can lead to failure of an remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height infant or child restraint.
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Can the child sit all the way back against the back of WARNING! (Continued) the vehicle seat? • When your child restraint is not in use, secure it in 2. Do the child’s knees bend comfortably over the front the vehicle with the seat belt or LATCH anchor- of the vehicle seat –...
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 If the answer to any of these questions was “no,” then the WARNING! child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit peri- Never allow a child to put the shoulder belt under an odically and make sure the seat belt buckle is latched.
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Use any attachment method shown with an “X” Below Combined LATCH – Weight of the LATCH – Restraint Type Lower Anchors Seat Belt + Top Child + Child Lower Anchors Seat Belt Only + Top Tether...
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Lower Anchors And Tethers For Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Captains Chairs Second Row (6 passenger) Lower Anchorage Symbol 2 anchorages per seating position 60/40 Second Row (7 Passenger) Top Tether Anchorage Symbol •...
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH an- child and the child restraint is chorage system to attach the child 65 lbs (29.5 kg).
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be at- Never “share” a LATCH anchorage tached using a common lower with two or more child restraints. LATCH anchorage? If the center position does not have dedicated LATCH lower anchor- ages, use the seat belt to install a child seat in the center position next to a child seat using the...
Page 99 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 100 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Captains Chair LATCH Anchorages Top Tether Strap Mounting (Captain’s Chair) Locating The LATCH Anchorages — Captain’s LATCH-compatible child restraint systems will be Chairs equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower There are tether strap anchorages behind each anchorage and a way to tighten the connection to the...
Page 101 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Locating The LATCH Anchorages —...
Page 102 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rear-facing infant restraints will also be equipped with a tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage.
Page 103 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Vehicles With A Center Arm Rest Tether For rearward facing infant seats secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the arm rest in the upward position.
Page 104 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Install A LATCH-Compatible Child Restraint 1. If the selected seating position has a Switchable Auto- matic Locking Retractor (ALR) seat belt, stow the seat belt following the instructions below. See the section “Installing Child Restraints Using the Vehicle Seat Belt”...
Page 105 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 move it to its rear-most position to make room for the 7. Test that the child restraint is installed tightly by child seat. You may also move the front seat forward pulling back and forth on the child seat at the belt to allow more room for the child seat.
Page 106 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Vehicle Seat WARNING! Belt • Improper installation of a child restraint to the The seat belts in the passenger seating positions are LATCH anchorages can lead to failure of an infant equipped with a Switchable Automatic Locking Retractor or child restraint.
Page 107 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Captains Chairs Second Row (6 Passenger) 60/40 Second Row (7 passenger)
Page 108 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to with the seat belt to attach a forward...
Page 109 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 Installing A Child Restraint With A Switchable 4. Pull on the webbing to make the lap portion tight Automatic Locking Retractor (ALR) against the child seat. 1. Place the child seat in the center of the seating 5.
Page 110 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the tether strap to the anchorage and tighten the tether rear-most position to make room for the child seat. strap. See the section “Installing Child Restraints You may also move the front seat forward to allow Using the Top Tether Anchorage”...
Page 111 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 strap. Refer to “Installing Child Restraints Using The If the belt still cannot be tightened after you shorten the Top Tether Anchorage” for directions to attach a tether buckle, disconnect the latch plate from the buckle, turn anchor.
Page 112 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchor- ages. Top Tether Strap Anchorage (Located on Seatback) 3.
Page 113 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 4. For the center seating position, route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat.
Page 114 112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • The top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. •...
Page 115: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 Transporting Pets Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or Air Bags deploying in the front seat could harm your pet. 55 mph (80 or 90 km/h) are desirable.
Page 116: Safety Tips
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! • Do not leave children or animals inside parked Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 117: Exhaust Gas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 118: Safety Checks You Should Make Inside The Vehicle
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The not lit during starting, see your authorized dealer. If the Vehicle light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Seat Belts Defroster Inspect the seat belt system periodically, checking for...
Page 119 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 120: Periodic Safety Checks You Should Make Outside The Vehicle
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 121: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Tilt Mirrors In Reverse (Available With Memory MIRRORS ......126 Seat Only) —...
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Rear Captain Chairs — If Equipped..163 SEATS ......144 ▫...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 ▫ Automatic High Beam — If Equipped ..177 ▫ Lane Change Assist ....185 ▫...
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Cancel ......204 ELECTRONIC SPEED CONTROL — IF EQUIPPED .
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 ▫ Service The ParkSense® Rear Park Assist FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED ... .225 System ......235 ▫...
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Canadian/Gate Operator Programming ..249 ▫ Wind Buffeting ..... . .255 ▫...
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 ▫ Rear Mini Center Console — If Equipped ..271 REAR WINDOW FEATURES ....276 ▫ Rear Window Wiper/Washer ... . .276 CARGO AREA FEATURES .
Page 128: Mirrors
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting.
Page 129: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Outside Mirrors Automatic Dimming Mirror — If Equipped To receive maximum benefit, adjust the outside mirrors A single ball joint mirror is provided in the vehicle. It is to center on the adjacent lane of traffic with a slight a twist on mirror that has a fixed position at the wind- overlap of the view obtained on the inside mirror.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The Automatic Dimming Mirror feature is disabled when the vehicle is in reverse gear to improve rear view viewing. • The Automatic Dimming Mirror feature can be turned on or off using the Uconnect® System. –...
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Assist Call NOTE: In case the 9-1-1 Call button is pushed in error, there will be a 10 second delay before the 9-1-1 Call The rear view mirror contains an ASSIST push button system initiates a call to a 9-1-1 operator.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. You should be able to speak with the 9-1-1 operator WARNING! through the vehicle audio system to determine if • If anyone in the vehicle could be in danger (e.g., additional help is needed. fire or smoke is visible, dangerous road conditions NOTE: Once a connection is made between the vehicle’s or location), do not wait for voice contact from a...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • The Phone Screen will display the following message WARNING! (Continued) “Vehicle phone requires service. Please contact your • Modifications to any part of the 9-1-1 Call system dealer.” could cause the air bag system to fail when you •...
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Wireless and/or Global Positioning Satellite signals Even if the 9-1-1 Call system is fully functional, factors beyond Chrysler Group LLC’s control may prevent or are unavailable or obstructed. stop the 9-1-1 Call system operation. These include, but •...
Page 135: Outside Mirrors Folding Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • Full rearward position General Information • Normal position This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Outside Automatic Dimming Mirrors — If This device may not cause harmful interference, and (2) Equipped this device must accept any interference received, includ-...
Page 136: Heated Mirrors - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE you want to adjust. Using the mirror control switch, press Power mirror preselected positions can be controlled by on any of the four arrows for the direction that you want the optional Memory Seat Feature. Refer to “Driver the mirror to move.
Page 137: Illuminated Vanity Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 then return to the original position when the vehicle is shifted out of REVERSE position. Each stored memory setting will have an associated Tilt Mirrors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not turned on when delivered from the factory.
Page 138: Blind Spot Monitoring (Bsm) - If Equipped
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED When the vehicle is started, the BSM warning light will be momentarily illuminated in both outside rear view The Blind Spot Monitoring (BSM) system uses two radar- mirrors to let the driver know that the system is opera- based sensors, located inside the rear bumper fascia, to tional.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the de- tection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. BSM Warning Light The BSM system monitors the detection zone from three different entry points (Side, Rear, Front) while driving to see if an alert is necessary.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Entering From The Rear Overtaking Traffic If you pass another vehicle slowly (with a relative speed Vehicles that come up from behind your vehicle on either of less than 15 mph (24 km/h) and the vehicle remains in side and enter the rear detection zone with a relative the blind spot for approximately 1.5 seconds, the warning speed of less than 30 mph (48 km/h).
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 143: Rear Cross Path
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
Page 145: Modes Of Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Modes Of Operation turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime Three selectable modes of operation are available in the will also be sounded.
Page 146: General Information
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Blind Spot Alert Off Operation is subject to the following two conditions: When the BSM system is turned off there will be no 1. The device may not cause harmful interference. visual or audible alerts from either the BSM or RCP 2.
Page 147: Power Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE move in the direction of the switch. Release the switch the seat will move in the direction of the switch. Release when the desired position has been reached. the switch when the desired position is reached. Adjusting The Seat Up Or Down WARNING! The height of the seats can be adjusted up or down.
Page 149: Passenger's Power Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Adjusting The Seat Up Or Down CAUTION! The height of the seats can be adjusted up or down. Pull Do not place any article under a power seat or upward or push downward on the seat switch, the seat impede its ability to move as it may cause damage to will move in the direction of the switch.
Page 150: Manual Front Passenger Seat Forward/Rearward Adjustment
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the lumbar support. Pushing upward or downward on Manual Front Passenger Seat Forward/Rearward the switch will raise and lower the position of the Adjustment support. Some models may be equipped with a manual front passenger seat.
Page 151: Manual Front Passenger Seatback Adjustment - Recline
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 While sitting in the seat, lift up on the bar located under Manual Front Passenger Seatback Adjustment — the seat cushion and move the seat forward or rearward. Recline Release the bar once you have reached the desired To adjust the seatback, lift the lever located on the position.
Page 152: Front Passenger Seat Fold-Flat Feature - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Front Passenger Seat Fold-Flat Feature —...
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 • Press the heated seat button once to turn the WARNING! HIGH setting ON. • Persons who are unable to feel pain to the skin • Press the heated seat button a second time to turn because of advanced age, chronic illness, diabetes, the LOW setting ON.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated seats can be programed to come on during a remote start. This feature can be programmed through the Uconnect® system.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 You can choose from HIGH, LOW or OFF heat settings. WARNING! Amber indicator lights in each switch indicate the level of • Persons who are unable to feel pain to the skin heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF.
Page 156: Front Ventilated Seats - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Ventilated Seats — If Equipped NOTE: The engine must be running for the ventilated seats to operate. Located in the seat cushion are small fans that draw the air from the passenger compartment and blow air Vehicles Equipped With Remote Start through fine perforations in the seat cover to help keep On models that are equipped with remote start, the...
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Active Head Restraints — Front Seats WARNING! Active Head Restraints are passive, deployable compo- The head restraints for all occupants must be prop- nents, and vehicles with this equipment cannot be readily erly adjusted prior to operating the vehicle or occu- identified by any markings, only through visual inspec- pying a seat.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head the back of your head, pull forward on the bottom of the restraint. To lower the head restraint, press the push head restraint. Push rearward on the bottom of the head button, located at the base of the head restraint, and push restraint to move the head restraint away from your downward on the head restraint.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center head restraint has limited adjustment. Lift WARNING! (Continued) upward on the head restraint to raise it, or push down- • Active Head Restraints may be deployed if they are ward on the head restraint to lower it. struck by an object such as a hand, foot or loose cargo.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Touch the “Controls” soft-key located on the bottom of WARNING! the Uconnect® display. Sitting in a seat with the head restraint in its lowered Touch the Headrest Fold soft-key to position could result in serious injury or death in a power fold the third row head collision.
Page 162: 60/40 Split Rear Seat
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Rear Seat Fold-Flat The second row seats can be folded flat to carry cargo. Pull upward on the release lever located on the outboard side of the seat. Fold-Flat Second Row Seat Release Lever...
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Easy Access For Third Row 2. Tumble the seat forward using the pull strap located behind the seatback. Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) row seat. Failure to follow these instructions could result in personal injury. To Raise Rear Seat Tumbled the seat rearward and lock it into place. WARNING! Be certain that the seatback is securely locked into position.
Page 165: Rear Captain Chairs - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Rear Captain Chairs — If Equipped Fold-Flat The second row seats can be folded flat to carry cargo. Pull upward on the release lever located on the outboard side of the seat. Fold-Flat Second Row Seats Release Lever...
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Access For Third Row 2. Tumble the seat forward using the pull strap located behind the seatback. Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! Do not drive the vehicle with the second row seats in the tumbled position. The second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
Page 168: Folding Third Row
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise Rear Seat Tumbled the seat rearward and lock it into place. WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
Page 169: Driver Memory Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Page 170 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Your vehicle is equipped with two RKE transmit- ters, one RKE transmitter can be linked to memory position 1 and the other transmitter can be linked to memory position 2. The memory seat switch is located on the driver’s door trim panel.
Page 171: Programming The Memory Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Programming The Memory Feature 4. Within five seconds, press and release either of the memory buttons (1) or (2). The Electronic Vehicle NOTE: To create a new memory profile, perform the Information Center (EVIC) will display which following: memory position has been set.
Page 172: Linking And Unlinking The Remote Keyless Entry Transmitter To Memory
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Within five seconds, press and release either of the Linking And Unlinking The Remote Keyless Entry memory buttons (1) or (2). The Electronic Vehicle Transmitter To Memory Information Center (EVIC) will display which Your RKE transmitters can be programmed to recall one memory position has been set.
Page 173: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To program your RKE transmitters, perform the follow- NOTE: Your RKE transmitters can be unlinked to your ing: memory settings by pressing the SET (S) button, and within 10 seconds, followed by pressing the UNLOCK 1.
Page 174: Easy Entry/Exit Seat
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Two Memory Position Recall The distance the driver seat moves depends on where you have the driver seat positioned when you remove the • To recall the memory setting for driver two using the Key Fob from the ignition (or change the ignition to OFF, memory switch, press MEMORY button number 2 on for vehicles equipped with Keyless Enter-N-Go™).
Page 175: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 will return to its previously set position when you TO OPEN AND CLOSE THE HOOD place the ignition to the ACC or RUN position. To open the hood, two latches must be released. •...
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach under the hood from outside the vehicle, move CAUTION! the safety latch to the left and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
Page 177: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).
Page 178: Automatic Headlights - If Equipped
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Automatic Headlights — If Equipped • Your vehicle is equipped with plastic headlight and This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, fog light (if equipped) lenses that are lighter and less rotate the headlight switch counterclockwise to the susceptible to stone breakage than glass lights.
Page 179: Automatic High Beam - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 through the Uconnect® system. Refer to “Uconnect® NOTE: Settings/Customer Programmable Features” in “Under- • If the windshield or automatic high beam mirror is standing Your Instrument Panel” for further information. replaced, the automatic high beam mirror must be NOTE: When your headlights come on during the day- re-aimed to ensure proper performance.
Page 180: Daytime Running Lights - If Equipped
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Turn the headlight switch to the AUTO headlight ignition is switched to the OFF or ACC position or the position. parking brake is engaged. The headlight switch must be used for normal nighttime driving. 3.
Page 181: Parking Lights And Panel Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: The headlight delay time is programmable through the Uconnect® System. Refer to “Uconnect® Settings/Customer Programmable Features” in “Under- standing Your Instrument Panel” for further information. Parking Lights And Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise.
Page 182: Interior Lights
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn off when the switch is pushed a second time, when The brightness of the instrument panel lighting can be the headlight switch is rotated to the off position, or the regulated by rotating the dimmer control up (brighter) or high beam is selected.
Page 183: Lights-On Reminder
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated all the way up to the dome ON position for 10 minutes, the interior lights will automatically turn off.
Page 184: Front Map/Reading Lights - If Equipped
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights — If Equipped second time. The lights will also turn on when the UNLOCK button on the Remote Keyless Entry (RKE) is The front map/reading lights are mounted in the over- pressed.
Page 185: Courtesy Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Courtesy Lights Ambient Light — If Equipped The courtesy lights can be turned on by pressing the top The overhead console is equipped with an ambient light corner of the lens. To turn the lights off, press the lens a feature.
Page 186: Multifunction Lever
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever Turn Signals The multifunction lever is located on the left side of the Move the multifunction lever up or down and the arrows steering column. on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 187: Lane Change Assist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Lane Change Assist WINDSHIELD WIPERS AND WASHERS Tap the lever up or down once, without moving beyond The windshield wiper/washer controls are located on the multifunction lever on the left side of the steering col- the detent, and the turn signal (right or left) will flash umn.
Page 188: Windshield Wiper Operation
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation CAUTION! Rotate the end of the lever to one of the first four detent Always remove any buildup of snow that prevents positions for intermittent settings, the fifth detent for low the windshield wiper blades from returning to the wiper operation and the sixth detent for high wiper “park”...
Page 189: Windshield Washer Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected. Intermittent Wiper Operation NOTE: If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.
Page 190: Mist
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the end of the lever is pushed while the wipers are in NOTE: The mist feature does not activate the washer the off position, the wipers will operate for several wipe pump; therefore, no washer fluid will be sprayed on the cycles, then turn off.
Page 191: Rain Sensing Wipers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 • The Rain Sensing feature may not function properly Rain Sensing Wipers — If Equipped when ice, or dried salt water is present on the wind- This feature senses moisture on the windshield and shield.
Page 192: Tilt/Telescoping Steering Column
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Transmission In NEUTRAL Position — When the TILT/TELESCOPING STEERING COLUMN ignition is ON, and the automatic transmission is in This feature allows you to tilt the steering column the NEUTRAL position, the Rain Sensing system will upward or downward.
Page 193: Power Tilt/Telescoping Steering Column - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 To unlock the steering column, push the lever downward POWER TILT/TELESCOPING STEERING COLUMN (toward the floor). To tilt the steering column, move the — IF EQUIPPED steering wheel upward or downward as desired. To This feature allows you to tilt the steering column lengthen or shorten the steering column, pull the steering upward or downward.
Page 194 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmit- ter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre- programmed positions.
Page 195: Heated Steering Wheel - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 HEATED STEERING WHEEL — IF EQUIPPED Vehicles Equipped With Remote Start The steering wheel contains a heating element that helps On models that are equipped with remote start, the warm your hands in cold weather. The heated steering heated steering wheel can be programmed to come on wheel has only one temperature setting.
Page 196: Equipped
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. ELECTRONIC SPEED CONTROL —...
Page 197: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 198: To Deactivate
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate The speed increment shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h): A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the U.S.
Page 199: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 • If the button is continually pressed, the set speed will To Decrease Speed continue to decrease until the button is released, then When the Electronic Speed Control is set, you can de- the new set speed will be established.
Page 200: Adaptive Cruise Control (Acc) - If Equipped
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC will allow you to keep cruise control engaged in WARNING! light to moderate traffic conditions without the constant need to reset your cruise control. ACC utilizes a radar Electronic Speed Control can be dangerous where the sensor and a forward facing camera designed to detect a system cannot maintain a constant speed.
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 WARNING! WARNING! (Continued) • Cannot take street, traffic, and weather condi- • Adaptive Cruise Control (ACC) is a convenience tions into account, and may be limited upon system. It is not a substitute for active driving adverse sight distance conditions.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Cruise Control system has two control modes: WARNING! (Continued) • Adaptive Cruise Control mode for maintaining an • When driving in fog, heavy rain, heavy snow, sleet, appropriate distance between vehicles. heavy traffic, and complex driving situations (i.e., in highway construction zones).
Page 203: Adaptive Cruise Control (Acc) Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Adaptive Cruise Control (ACC) Operation The speed control buttons (located on the right side of the steering wheel) operates the ACC system. Adaptive Cruise Control Buttons 1 — NORMAL (FIXED SPEED) CRUISE CONTROL ON/OFF 2 —...
Page 204: Activating Adaptive Cruise Control (Acc)
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When in Four-Wheel Drive Low. NOTE: Any chassis/suspension or tire size modifications to the vehicle will effect the performance of the Adaptive • When you apply the brakes. Cruise Control. • When the parking brake is set. Activating Adaptive Cruise Control (ACC) •...
Page 205 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Adaptive Cruise Control Ready Adaptive Cruise Control Off To turn the system OFF, push and release the Adaptive WARNING! Cruise Control (ACC) ON/OFF button again. At this time, the system will turn off and the EVIC will display Leaving the Adaptive Cruise Control (ACC) system “Adaptive Cruise Control (ACC) Off.”...
Page 206: To Set A Desired Acc Speed
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Remove your foot from the accelerator pedal. If you do WARNING! (Continued) not, the vehicle may continue to accelerate beyond the set want. You could lose control and have a collision. speed. If this occurs: Always leave the system off when you are not using •...
Page 207: To Turn Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 • The shift lever/gear selector is removed from the • The Normal (Fixed Speed) Electronic Speed Control Drive position. ON/OFF button is pressed. • The Electronic Stability Control/Traction Control Sys- • The ignition is turned OFF. tem (ESC/TCS) activates.
Page 208: To Vary The Speed Setting
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE U.S. Speed (mph) WARNING! • Pressing the SET + button once will result in a 1 mph The Resume function should only be used if traffic increase in set speed. Each subsequent tap of the and road conditions permit.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 To Decrease Speed Metric Speed (km/h) • Pressing the SET - button once will result in a 1 km/h While ACC is set, the set speed can be decreased by pressing the SET - button. decrease in set speed.
Page 210: Setting The Following Distance In Acc
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ACC system decelerates the vehicle to a full stop Using this distance setting and the vehicle speed, ACC when following a target vehicle. If an ACC host vehicle calculates and sets the distance to the vehicle ahead. This follows a target vehicle to a standstill, after two distance setting displays in the EVIC.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
Page 212 210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease the distance setting, press the Distance Setting — Decrease button and release. Each time the button is pressed, the distance setting decreases by one bar (shorter). If there is no vehicle ahead, the vehicle will maintain the set speed.
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 • The distance setting is changed. • The system disengages. (Refer to the information on ACC Activation). The maximum braking applied by ACC is limited; how- ever, the driver can always apply the brakes manually, if necessary.
Page 214: Overtake Aid
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtake Aid ACC Operation At Stop When driving with ACC engaged and following a target If the ACC system brings your vehicle to a standstill vehicle, the system will provide an additional accelera- while following a target vehicle, if the target vehicle starts tion to assist in passing vehicles in front.
Page 215: Adaptive Cruise Control (Acc) Menu
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Adaptive Cruise Control Ready WARNING! When ACC is activated but the vehicle speed setting has When the ACC system is resumed, the driver must not been selected, the display will read “Adaptive Cruise ensure that there are no pedestrians, vehicles or Control Ready.”...
Page 216: Display Warnings And Maintenance
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • System Off dirt or ice. In these cases, the EVIC will display “ACC/ FCW Unavailable Wipe Front Radar Sensor” and the • ACC Proximity Warning system will deactivate. • ACC Unavailable Warning The “ACC/FCW Unavailable Wipe Front Radar Sensor”...
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 • If the sensor or front end of the vehicle is damaged due If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of to a collision, see your authorized dealer for service.
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass. In these cases, the EVIC will • If the “ACC/FCW Unavailable Wipe Front Radar display “ACC/FCW Limited Functionality Clean Front Sensor”...
Page 219: Precautions While Driving With Acc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 When the condition that created limited functionality is Precautions While Driving With ACC no longer present, the system will return to full function- In certain driving situations, ACC may have detection ality. issues. In these cases, ACC may brake late or unexpect- edly.
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Offset Driving Turns And Bends ACC may not detect a vehicle in the same lane that is When driving on a curve with ACC engaged, the system offset from your direct line of travel, or a vehicle merging may decrease the vehicle speed and acceleration for in from a side lane.
Page 221 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Turn Or Bend Example ACC Hill Example Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane.
Page 222 220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE it is completely in the lane. There may not be sufficient Narrow Vehicles distance to the lane-changing vehicle. Always be atten- Some narrow vehicles traveling near the outer edges of tive and ready to apply the brakes if necessary. the lane or edging into the lane are not detected until they have moved fully into the lane.
Page 223: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary FCC Requirements For Vehicular Radar Systems vehicles. For example, ACC will not react in situations Classification Specifications: where the vehicle you are following exits your lane and 47 C.F.R.
Page 224 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE which turns the ACC and the NORMAL (Fixed Speed) To Set A Desired Speed ELECTRONIC SPEED CONTROL OFF. Pressing of the NORMAL (Fixed Speed) ELECTRONIC SPEED CON- Turn the Normal (Fixed Speed) Electronic TROL ON/OFF button will result in turning ON (chang- Speed Control ON.
Page 225 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 • If the button is continually pressed, the set speed will The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: continue to increase in 10 km/h increments until the button is released.
Page 226 224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pressed, the set speed will To Cancel continue to decrease in 5 mph increments until the The following conditions will cancel the Normal (Fixed button is released. The decrease in set speed is re- Speed) Electronic Speed Control without clearing the flected in the EVIC display.
Page 227: Forward Collision Warning (Fcw) With Mitigation - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 To Resume Speed FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED To resume a previously set speed, push the RES button and release. Resume can be used at any speed above Forward Collision Warning (FCW) With Mitigation 20 mph (32 km/h).
Page 228 226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller (EBC), to calculate the probability of a forward collision. When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and may provide a brake jerk warning.
Page 229: Turning Fcw On Or Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 NOTE: WARNING! • The minimum speed for FCW activation is 5 mph Forward Collision Warning (FCW) is not intended to (10 km/h). avoid a collision on its own, nor can FCW detect • The FCW alerts may be triggered on objects other than every type of potential collision.
Page 230: Changing Fcw And Active Braking Status
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the FCW system back ON, press the forward Changing FCW And Active Braking Status collision button again to turn the system ON (led turns The FCW Sensitivity And Active Braking Settings are off).
Page 231: Fcw Limited Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 NOTE: Once the condition that limited the system performance is no longer present, the system will return to its full • The system will retain the last setting selected by the performance state. If the problem persists, see your driver after ignition shut down.
Page 232: Parksense® Sensors
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE during a parking maneuver. Refer to ParkSense® System ParkSense® Sensors Usage Precautions for limitations of this system and The four ParkSense® sensors, located in the rear fascia/ recommendations. bumper, monitor the area behind the vehicle that is within the sensors’...
Page 233: Parksense® Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 ParkSense® Warning Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Customer - Programmable Features section of the Uconnect® Sys- tem. Refer to Uconnect® Settings” in “Understanding Your Instrument Panel”...
Page 234 232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous. Slow Tone Single 1/2 Second Tone...
Page 235 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 Fast Tone Continuous Tone...
Page 236 234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS Rear Distance Greater than...
Page 237: Enabling And Disabling Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Enabling And Disabling ParkSense® system requires service, the ParkSense® switch LED will blink momentarily, and then the LED will be ON. ParkSense® can be enabled and disabled with the ParkSense® switch. Service The ParkSense® Rear Park Assist System When the ParkSense®...
Page 238: Cleaning The Parksense® System
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE message for as long as the vehicle is in REVERSE. Under ParkSense® System Usage Precautions this condition, ParkSense® will not operate. NOTE: If “PARKSENSE UNAVAILABLE WIPE REAR SEN- • Ensure that the rear bumper is free of snow, ice, mud, SORS”...
Page 239 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 • ParkSense®, when on, will reduce the volume of the CAUTION! radio when it is sounding a tone. • ParkSense® is only a parking aid and it is unable to • Clean the ParkSense® sensors regularly, taking care recognize every obstacle, including small obstacles.
Page 240 238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Before using ParkSense®, it is strongly recom- • Drivers must be careful when backing up even mended that the ball mount and hitch ball assem- when using ParkSense®. Always check carefully bly is disconnected from the vehicle when the behind your vehicle, look behind you, and be sure vehicle is not used for towing.
Page 241: Parkview® Rear Back Up Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 PARKVIEW® REAR BACK UP CAMERA — IF When the vehicle is shifted out of REVERSE (with camera EQUIPPED delay turned ON), the rear view image with dynamic grid lines will be displayed for up to 10 seconds after Your vehicle may be equipped with the ParkView®...
Page 242 240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When enabled, active guide lines are overlaid on the vehicle while a dashed center-line will indicate the center image to illustrate the width of the vehicle and its of the vehicle to assist with aligning to a hitch/receiver. projected backup path based on the steering wheel The following table shows the approximate distances for position.
Page 243: Overhead Console
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 OVERHEAD CONSOLE CAUTION! The overhead console contains courtesy/reading lights • To avoid vehicle damage, ParkView® should only and storage for sunglasses. Universal Garage Door be used as a parking aid. The ParkView® camera is Opener (HomeLink®), power liftgate and power sunroof unable to view every obstacle or object in your switches may also be included, if equipped.
Page 244: Front Map/Reading Lights - If Equipped
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights — If Equipped To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will Lights are mounted in the overhead console. Each light also turn on when the UNLOCK button on the RKE is can be turned on by pressing the switch on either side of pressed.
Page 245: Courtesy Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 Courtesy Lights Sunglasses Bin Door The courtesy lights can be turned on by pressing the top At the front of the console a compartment is provided for corner of the lens. To turn the lights off, press the lens a the storage of a pair of sunglasses.
Page 246: Garage Door Opener - If Equipped
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit operates off your vehicle’s battery.
Page 247: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.
Page 248: Programming A Rolling Code
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
Page 249 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) Firmly press and release the “LEARN” or “TRAIN- away from the HomeLink® button you wish to pro- ING” button. On some garage door openers/devices gram while keeping the HomeLink®...
Page 250: Programming A Non-Rolling Code
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- To reprogram a channel that has been previously trained, gram while keeping the HomeLink®...
Page 251: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 • To program the remaining two HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
Page 252 250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the indicator light stays on constantly, program- 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- ming is complete and the garage door/device should gram while keeping the HomeLink®...
Page 253: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 3. Without releasing button proceed with The HomeLink® Universal Transceiver is disabled when “Canadian/Gate Operator Programming” step 2 and the Vehicle Security Alarm is active. follow all remaining steps. Troubleshooting Tips Using HomeLink® If you are having trouble programming HomeLink®, To operate, press and release the programmed here are some of the most common solutions:...
Page 254: General Information
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following while you are training the universal transceiver. Do two conditions: not train the transceiver if people, pets or other 1.
Page 255: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children unattended in a vehicle, or visors on the overhead console. with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children.
Page 256: Opening Sunroof - Express
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE movement. The sunroof and sunshade will remain in a WARNING! (Continued) partially opened condition until the switch is pushed and • Do not allow small children to operate the sunroof. held rearward again. Never allow your fingers, other body parts, or any Closing Sunroof —...
Page 257: Pinch Protect Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 Pinch Protect Feature Sunshade Operation This feature will detect an obstruction in the opening of The sunshade can be opened manually. However, the the sunroof during Express Close operation. If an ob- sunshade will open automatically as the sunroof opens. struction in the path of the sunroof is detected, the NOTE: The sunshade cannot be closed if the sunroof is sunroof will automatically retract.
Page 258: Sunroof Maintenance
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance ELECTRICAL POWER OUTLETS Use only a non-abrasive cleaner and a soft cloth to clean Your vehicle is equipped with 12 Volt (13 Amp) power the glass panel. outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories.
Page 259 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 • To ensure proper operation a MOPAR® knob and The front power outlet is located inside the storage area element must be used. on the center stack of the instrument panel. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts.
Page 260 258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. Rear Full Center Console Outlet The rear cargo power outlet is located in the right rear cargo area.
Page 261 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 Rear Cargo Power Outlet Rear Cargo Power Outlet Fuse NOTE: The rear cargo power outlet can be switched to “battery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel.
Page 262 260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 263: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 POWER INVERTER — IF EQUIPPED CAUTION! There is a 115 Volt, 150 Watt inverter outlet located on the • Many accessories that can be plugged in draw back of the center console to convert DC current to AC power from the vehicle’s battery, even when not in current.
Page 264 262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the circuit, check the power ratings on electrical devices prior to using the inverter. WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. •...
Page 265: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 CUPHOLDERS Rear Cupholders Rear Center Arm Rest Cupholders — If Equipped Front Seat Cupholders There are two cupholders for the rear seat passengers There are two cupholders for the front seat passengers located in the fold-down center armrest. located in the center console.
Page 266 264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Full Console Cupholders — If Equipped The rear full console cupholders are equipped with a light ring that illuminates the cupholders for the rear There are two cupholders for the rear seat passengers passengers.
Page 267: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 Rear Mini Console Cupholders — If Equipped STORAGE There are two cupholders for the rear seat passengers Glove Compartment located in the front of the rear mini console. The glove compartment is located on the right side of the instrument panel.
Page 268: Door Storage
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage Front Center Console Large storage areas are built into the door panels for easy The front center console contains both an upper and a access. lower storage area. To open the upper storage compartment, pull upward on the small latch located on the lid.
Page 269: Rear Full Center Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 Lift upward on the larger of the latches to access the To open the upper storage compartment, pull upward on lower storage compartment. the small latch located on the front of the lid. Rear Full Center Console —...
Page 270 268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Lower storage compartment light is always on The upper storage compartment may also be lifted for- with ignition in the ON/RUN position. ward. Push in the release button located on the back of the lid.
Page 271 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 Storage Compartment Rear Push Button Lower Storage Compartment When lifted forward there is access to the lower storage NOTE: When the lower storage compartment is accessed compartment. it allows the armrest to flip forward for “fold flat mode”. Fold flat mode allows the console armrest to be lowered below fold flat seat plane and protect the armrest vinyl from damage when using the vehicle to haul cargo.
Page 272 270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold Flat Mode Console Cubby Bins Open storage areas, or cubby bins with removable liners, are located rearward of the cupholders and in the lower front of the console.
Page 273: Rear Mini Center Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 Rear Mini Center Console — If Equipped An open storage area, or cubby bin with removable liner, is located in the front of the console. Console Cubby Bin...
Page 274: Cargo Area Features
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Rechargeable Flashlight The rechargeable flashlight is mounted on the left side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place.
Page 275: Cargo Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 Load Floor Handle Three-Press Switch Cargo Storage Retractable Cargo Area Cover — If Equipped There is a removable storage bin located on the left side NOTE: The purpose of this cover is for privacy, not to of the rear cargo area.
Page 276: Cargo Tie-Down Hooks
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To cover the cargo area: Cargo Tie-Down Hooks The cargo tie-downs, located on the cargo area floor, 1. Grasp the cover at the center handle. Pull it over the should be used to safely secure loads when the vehicle is cargo area.
Page 277 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 WARNING! WARNING! (Continued) • Do not carry loads which exceed the load limits • To help protect against personal injury, passengers described on the label attached to the left door or should not be seated in the rear cargo area. The rear left door center pillar.
Page 278: Rear Window Features
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer controls are located on the mul- tifunction lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever.
Page 279: Rear Window Defroster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 release of the switch, the wipers will resume the continu- mirrors (if equipped). An indicator in the button will ous rear wiper operation. When this rotary control is in illuminate when the rear window defroster is on. The the OFF position, rotating it downward will activate the rear window defroster automatically turns off after ap- rear washer pump which will continue to operate as long...
Page 280: Roof Luggage Rack - If Equipped
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack.
Page 281: Deploying The Crossbars
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 Deploying the Crossbars Remove the crossbar from the stowed position by sliding the crossbar towards the center of the roof. Repeat with Starting with one crossbar, completely loosen the thumb crossbar on the opposite side. screws at both ends of the crossbar.
Page 282 280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position the crossbars across the roof making sure the CAUTION! letters on the crossbars align with the matching letters on the side rail. Be careful when handling the crossbars to prevent damage to the vehicle. Starting with one crossbar, bend down the pivot supports at each end.
Page 283: Stowing The Crossbars
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 crossbar is fully deployed with the crossbar pushed as far into the slot as possible. Once the crossbar is in place, tighten both thumb screws completely. Deployed Crossbars Stowing The Crossbars Starting with one crossbar, completely loosen the thumb Installing Crossbars screws at both ends.
Page 284 282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then, position the crossbar along the correct side rail. CAUTION! Make sure the letters on the crossbar align with the matching letters on the side rail. Be careful when handling the crossbars to prevent damage to the vehicle.
Page 285 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Slide the crossbar outward, away from the center of the Once the driver’s side crossbar is in place, tighten the roof. The crossbar will nest fully within the side rail. thumb screws completely. Crossbar To Side Rail Tightening Crossbar...
Page 286 284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Repeat the procedure to stow the second crossbar on the NOTE: opposite side. • To help control wind noise, stow the crossbars in the side rails when they are not in use. • If any metallic object is placed over the satellite radio antenna (if equipped), you may experience interrup- tion of satellite radio reception.
Page 287 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 CAUTION! CAUTION! (Continued) • Load should always be secured to cross bars first, • To prevent damage to the roof of your vehicle, DO with tie down loops used as additional securing NOT carry any loads on the roof rack without the points if needed.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ EVIC Red Telltales .....309 INSTRUMENT PANEL FEATURES ..290 ▫...
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Customer Programmable Features — ▫ Blu-ray™ Disc Player Remote Control — If Uconnect® 8.4 Settings ....339 Equipped ......367 ▫...
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 ▫ Rear Automatic Temperature Control (ATC) — If CLIMATE CONTROLS ....382 Equipped ......392 ▫...
Page 292: Instrument Panel Features
290 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Lower Switch Bank 11 — Fuel Door Release 2 — Instrument Cluster 7 — Hazard Switch 12 — Headlight Switch 3 — Radio 8 — ESC Button 13 —...
Page 293: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 291 INSTRUMENT CLUSTER...
Page 294: Instrument Cluster Descriptions
292 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 3. Anti-Lock Brake (ABS) Light 1. Tachometer This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition Indicates the engine speed in revolutions per minute switch is turned to the ON/RUN position and (RPM x 1000).
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 5. Front Fog Light Indicator — If Equipped 8. Speedometer This indicator will illuminate when the front fog Indicates vehicle speed. lights are on. 9. Selectable EVIC Information 6. Selectable EVIC Information This area of the cluster will display selectable informa- This area of the cluster will display selectable informa- tion such as compass, outside temperature, etc.
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL Certain conditions, poor fuel quality, etc., may illuminate WARNING! (Continued) the light after engine start. The vehicle should be serviced operating conditions. This can cause a fire if you if the light stays on through several of your typical drive slowly or park over flammable substances such driving cycles.
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been NOTE: The light may flash momentarily during sharp disengaged, and the fluid level is at the full mark on the cornering maneuvers, which change fluid level condi- master cylinder reservoir, it indicates a possible brake tions.
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 Operation of the Brake Warning Light can be checked by 15. Tire Pressure Monitoring Telltale Light turning the ignition switch from the OFF position to the Each tire, including the spare (if provided), ON/RUN position. The light should illuminate for ap- should be checked monthly when cold and proximately two seconds.
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL reduces fuel efficiency and tire tread life, and may affect alternate tires or wheels on the vehicle that prevent the the vehicle’s handling and stopping ability. TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more Please note that the TPMS is not a substitute for proper tires or wheels on your vehicle, to ensure that the tire maintenance, and it is the driver’s responsibility to...
Page 301 UNDERSTANDING YOUR INSTRUMENT PANEL 299 16. Electronic Vehicle Information Center (EVIC) When the appropriate conditions exist, this display Display/Odometer Display shows the Electronic Vehicle Information Center (EVIC) messages. Refer to “Electronic Vehicle Information Cen- The odometer display shows the total distance the ve- ter”...
Page 302 300 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Vehicle Security Light ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction Indicator This light will flash rapidly for approximately Light” comes on continuously with the engine running, a 15 seconds when the vehicle theft alarm is malfunction has been detected in the ESC system.
Page 303: Electronic Vehicle Information
UNDERSTANDING YOUR INSTRUMENT PANEL 301 • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation. 22. Park/Headlight ON Indicator — If Equipped This indicator will illuminate when the park lights or headlights are turned on.
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL • Fuel Economy • Trip • Audio • Stored Messages • Screen Setup • Speed Warning — If Equipped The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: EVIC Steering Wheel Buttons •...
Page 305: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 303 • DOWN Arrow Button Electronic Vehicle Information Center (EVIC) Displays Push and release the DOWN button to scroll The EVIC displays are located in the center portion of the downward through the main menu. cluster and consists of multiple sections: •...
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL • Unstored Messages The main display area will normally display the main menu or the screens of a selected feature of the main This message type is displayed indefinitely or until the menu. The main display area also displays “pop up” condition that activated the message is cleared.
Page 307: Engine Oil Change Indicator System
UNDERSTANDING YOUR INSTRUMENT PANEL 305 Battery Saver Mode/Battery Saver On Message — Engine Oil Change Indicator System If Equipped Oil Change Required When the Battery Saver Mode or “Battery Saver On Your vehicle is equipped with an engine oil change message is displayed, the vehicle will turn off certain indicator system.
Page 308: Electronic Vehicle Information Center (Evic) Messages
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Passenger Seatbelt Unbuckled Vehicles Equipped With Keyless Enter-N-Go™ • Service Airbag System 1. Without pressing the brake pedal, press the ENGINE START/STOP button and cycle the ignition to the • Traction Control Off ON/RUN position (do not start the engine.) •...
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 • Tire Pressure Screen With Low Tire(s) “Inflate Tire to • Vehicle Not in Park XX” • Key in Ignition • Service Tire Pressure System • Key in Ignition Lights On • Parking Brake Engaged •...
Page 310: Evic Amber Telltales
308 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Airbag Warning Light • Service Shifter • Door Open • Engage Park Brake to Prevent Rolling • Doors Open • Transmission Too cold Idle with Engine On • Liftgate Open • Washer Fluid Low •...
Page 311: Evic Red Telltales
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • Windshield Washer Fluid Low Indicator collision. For further information, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features This telltale will turn on to indicate the wind- Of Your Vehicle.” shield washer fluid is low. •...
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Pressure Warning Light electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the This telltale indicates low engine oil pressure. If vehicle is experiencing a problem with the charging the light turns on while driving, stop the vehicle and shut system.
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 vehicle has completely stopped and the gear selector is If the light turns on while driving, safely pull over and placed in the PARK position. The light should turn off. stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- If the light remains lit with the engine running, your hicle.
Page 314: Evic Green Telltales
312 UNDERSTANDING YOUR INSTRUMENT PANEL • Adaptive Cruise Control EVIC Green Telltales • Electronic Speed Control SET This light will turn on when the ACC is ON. For further information, refer to “Adaptive Cruise Control (ACC)” in This telltale will illuminate green when the “Understanding The Features Of Your Vehicle.
Page 315 UNDERSTANDING YOUR INSTRUMENT PANEL 313 MPH To km/h If tire pressure is OK for all tires a vehicle ICON is displayed with tire pressure values in each corner of the ICON. Press and release the UP or DOWN arrow button until the MPH to km/h icon is high- If one or more tires have low pressure, “Inflate Tire To lighted in the EVIC.
Page 316 314 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Temperature (Automatic Transmission Oil Life Only) Press and release the RIGHT or LEFT arrow button until Press and release the RIGHT or LEFT arrow button until “Oil Life” is highlighted in the EVIC. Press and release “Transmission Temperature”...
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 • Distance Fuel Economy • Average Fuel Economy Press and release the UP or DOWN arrow • Elapsed Time button until the Fuel Economy icon is highlighted. Hold the OK button to reset all the information. •...
Page 318: Screen Setup Driver Selectable Items
316 UNDERSTANDING YOUR INSTRUMENT PANEL Audio Screen Setup feature allows you to change what informa- tion is displayed in the instrument cluster as well as the Press and release the UP or DOWN arrow button until location that information is displayed. the Audio Menu item is highlighted in the EVIC.
Page 319 UNDERSTANDING YOUR INSTRUMENT PANEL 317 • Compass (default setting) Upper Left • None • Outside Temp • Gear Display • Time • Compass • Range To Empty (RTE) • Outside Temp (default setting) • Fuel Economy Average • Time • Fuel Economy Current •...
Page 320: Uconnect® Settings
318 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® SETTINGS The Uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable features. Uconnect® 5.0 Soft-Keys And Hard-Keys 1 —...
Page 321: Hard-Keys
UNDERSTANDING YOUR INSTRUMENT PANEL 319 Hard-Keys Hard-Keys are located below the Uconnect® system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), press the center of the control knob one or more times to select or change a...
Page 322: Soft-Keys
320 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys next to the setting, showing that setting has been se- lected. Once the setting is complete, either press the Back Soft-Keys are accessible on the Uconnect® display. Arrow soft-key or the Back hard-key to return to the Customer Programmable Features —...
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 • Display Brightness With Headlights ON soft-key, then touch the desired language soft-key until a check-mark appears next to the language, showing that When in this display, you may select the overall screen setting has been selected. Touch the back arrow soft-key brightness with the headlights on.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL • Show Command List designated turn within a programmed route. To make your selection, touch the “Navigation Turn-By-Turn In When in this display, you may choose to Never, With Cluster” soft-key, until a check-mark appears next to the Help or Always display the Teleprompter with possible setting, showing that setting has been selected.
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 • Sync Date • Forward Collision Warning — If Equipped When in this display, you may choose to set the date The Front Collision Warning (FCW) feature provides an automatically. Touch the “Sync Date” soft-key until a audible and/or visual warning to potential forward check-mark appears next to the setting, showing that collisions.
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL • Forward Collision Warning (FCW) — Active Braking visual) to indicate the proximity to other objects. The system can be enabled with Sound Only, or Sound and The FCW system includes Advanced Brake Assist (ABA). Display.
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 • Rear ParkSense® Chime Volume back arrow soft-key to return to the previous menu. Refer to “ParkSense® Rear Park Assist” in “Understanding The The Rear ParkSense® Chime Volume settings can be Features Of Your Vehicle” for system function and oper- selected from the EVIC or Uconnect®...
Page 328 326 UNDERSTANDING YOUR INSTRUMENT PANEL • Paddle Shifting The amount of directional torque the steering system can apply to the steering wheel to correct for vehicle lane Selecting this feature enables the use of steering wheel departure can be set at Low, Medium or High. To make paddle switches for shifting in manual mode.
Page 329 UNDERSTANDING YOUR INSTRUMENT PANEL 327 system is deactivated. To change the Blind Spot Alert rear of the vehicle above the rear License plate. To make status, touch the “Off,” “Lights” or “Lights & Chime” your selection, touch the “ParkView® Backup Camera” soft-key.
Page 330 328 UNDERSTANDING YOUR INSTRUMENT PANEL • ParkView® Backup Camera Delay setting, indicating that the setting had been selected. Touch the back arrow soft-key to return to the previous When the vehicle is shifted out of REVERSE (with camera menu. delay turned OFF), the rear camera mode is exited and •...
Page 331 UNDERSTANDING YOUR INSTRUMENT PANEL 329 on the windshield. To make your selection, touch the the “Brake Service” soft-key, until a check-mark appears “Rain Sensing” soft-key, until a check-mark appears next next to setting, indicating that the setting had been to setting, indicating that the setting had been selected. selected.
Page 332 330 UNDERSTANDING YOUR INSTRUMENT PANEL appears next to setting, indicating that the setting had soft-key to select your desired Interior Ambient Light been selected. Touch the back arrow soft-key to return to level. Touch the back arrow soft-key to return to the the previous menu.
Page 333 UNDERSTANDING YOUR INSTRUMENT PANEL 331 touch the “+” or “-” soft-key to select your desired time setting, indicating that the setting has been selected. interval. Touch the back arrow soft-key to return to the Touch the back arrow soft-key to return to the previous previous menu.
Page 334 332 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Lock selected. To make your selection, touch the “Flash Head- lights with Lock” soft-key, until a check-mark appears When this feature is selected, the horn will sound when next to setting, indicating that the setting has been the door locks are activated.
Page 335 UNDERSTANDING YOUR INSTRUMENT PANEL 333 • Passive Entry Keyless Entry (RKE) transmitter UNLOCK button. When 1st Push Of Key Fob Unlocks is selected, you must push This feature allows you to lock and unlock the vehicle’s the RKE transmitter UNLOCK button twice to unlock the door(s) without having to push the Remote Keyless Entry passenger’s doors.
Page 336 334 UNDERSTANDING YOUR INSTRUMENT PANEL • Auto-On Driver Heated/Ventilated Seat & Steering NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set Wheel With Vehicle Start — If Equipped to ON) when the Remote Keyless Entry (RKE) transmitter When this feature is selected the driver’s heated seat and is used to unlock the door.
Page 337 UNDERSTANDING YOUR INSTRUMENT PANEL 335 To make your selection, touch the Easy Exit Seats soft- Delay status touch the + or - soft-key to select your key, until a check-mark appears next to setting, showing desired time interval. Touch the back arrow soft-key to that setting has been selected.
Page 338 336 UNDERSTANDING YOUR INSTRUMENT PANEL • Perform Compass Calibration NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Lap- Touch the “Calibration” soft-key to change this setting. tops and Radar Detectors. This is where the compass This compass is self-calibrating, which eliminates the module is located, and it can cause interference with the need to manually reset the compass.
Page 339 UNDERSTANDING YOUR INSTRUMENT PANEL 337 • Equalizer • Surround Sound When in this display you may adjust the Bass, Mid and This feature provides simulated surround sound mode. Treble settings. Adjust the settings with the + and – To make your selection, touch the “Surround Sound” setting soft-keys or by selecting any point on the scale soft-key, select On or Off followed by pressing the back between the “+”...
Page 340 338 UNDERSTANDING YOUR INSTRUMENT PANEL Phone/Bluetooth® your selection, touch the “Channel Skip” soft-key, select the channels you would like to skip followed by pressing After pressing the “Phone/Bluetooth” soft-key the fol- the back arrow soft-key. lowing settings will be available: •...
Page 341: Uconnect® 8.4 Settings
UNDERSTANDING YOUR INSTRUMENT PANEL 339 • Clear Personal Data Restore Settings After pressing the “Restore Settings” soft-key the follow- When this feature is selected it will remove personal data ing settings will be available: including Bluetooth® devices and presets. To Clear Per- sonal Data touch the “Yes”...
Page 342: Understanding Your Instrument Panel
340 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Mode NOTE: Only one touchscreen area may be selected at a time. When in this display you may select one of the auto When making a selection, press the soft-key to enter the display settings.
Page 343 UNDERSTANDING YOUR INSTRUMENT PANEL 341 • Set Language • Voice Response Length When in this display, you may select one of multiple When in this display, you may change the Voice Re- languages (English / Français / Español) for all display sponse Length settings.
Page 344 342 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Time Hours designated turn within a programmed route. To make your selection, touch the “Navigation Turn-By-Turn In When in this display, you may adjust the hours. The Cluster” soft-key, until a check-mark appears next to the “Sync with GPS Time”...
Page 345 UNDERSTANDING YOUR INSTRUMENT PANEL 343 check-mark appears next to the 12hrs or 24hrs setting, the FCW status, touch and release the “Near” or “Far” showing that setting has been selected. Touch the back button. Then touch the back arrow soft-key. arrow soft-key to return to the previous menu.
Page 346 344 UNDERSTANDING YOUR INSTRUMENT PANEL • Lane Departure Warning (LDW) — If Equipped soft-key until a check-mark appears next to setting, indicating that the setting had been selected. Touch the The Lane Departure Warning (LDW) sets the distance at back arrow soft-key to return to the previous menu. which the steering wheel will provide feedback for •...
Page 347 UNDERSTANDING YOUR INSTRUMENT PANEL 345 equipped. The chime volume settings include LOW, to return to the previous menu. ParkSense® will retain its MEDIUM, and HIGH. The factory default volume setting last known configuration state through ignition cycles. is MEDIUM. To make your selection, touch the •...
Page 348 346 UNDERSTANDING YOUR INSTRUMENT PANEL previous position when the transmission is shifted out of the Blind Spot Monitor (BSM) system is activated and REVERSE. To make your selection, touch the “Tilt Mir- will only show a visual alert in the exterior mirrors. rors In Reverse”...
Page 349 UNDERSTANDING YOUR INSTRUMENT PANEL 347 • ParkView® Backup Camera — If Equipped display whenever the shift lever is put into REVERSE. The image will be displayed on the radio touchscreen Your vehicle may be equipped with the ParkView® Rear display along with a caution note to “check entire sur- Back Up Camera that allows you to see an on-screen roundings”...
Page 350 348 UNDERSTANDING YOUR INSTRUMENT PANEL five seconds, this note will disappear. To make your “Safety & Driving Assistance” soft-key. Press the selection, touch the “ParkView Backup Camera Static “Parkview Backup camera Delay” soft-key to turn the Gridlines” soft-key, until a check-mark appears next to ParkView®...
Page 351 UNDERSTANDING YOUR INSTRUMENT PANEL 349 • Headlights With Wipers — If Equipped the “Hill Start Assist” soft-key, until a check-mark ap- pears next to setting, indicating that the setting had been When this feature is selected, and the headlight switch is selected.
Page 352 350 UNDERSTANDING YOUR INSTRUMENT PANEL “Lights / SmartBeam™ — If Equipped” in “Understand- next to the setting, showing that setting has been se- ing The Features Of Your Vehicle” for further informa- lected. Touch the back arrow soft-key to return to the tion.
Page 353 UNDERSTANDING YOUR INSTRUMENT PANEL 351 touch the “Sound Horn With Lock” soft-key, until a passenger’s doors. When Unlock All Doors On 1st Push check-mark appears next to the setting, showing that the is selected, all of the doors will unlock on the first push of setting has been selected.
Page 354 352 UNDERSTANDING YOUR INSTRUMENT PANEL your selection, touch the “Passive Entry” soft-key, until a NOTE: The seat will return to the memorized seat check-mark appears next to the setting, showing that the location (if Recall Memory with Remote Key Unlock is set setting has been selected.
Page 355 UNDERSTANDING YOUR INSTRUMENT PANEL 353 • Auto-On Driver Heated/Ventilated Seat & Steering To make your selection, touch the Easy Exit Seats soft- Wheel With Vehicle Start — If Equipped key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow When this feature is selected the driver’s heated seat and soft-key to return to the previous menu.
Page 356 354 UNDERSTANDING YOUR INSTRUMENT PANEL Delay status, touch the “+” or “–” soft-key to select your NOTE: Keep magnetic materials, such as iPod’s®, Mo- desired time interval. Touch the back arrow soft-key to bile Phones, Laptops and Radar Detectors, away from the return to the previous menu.
Page 357 UNDERSTANDING YOUR INSTRUMENT PANEL 355 • Perform Compass Calibration • Equalizer Touch the “Calibration” soft-key to change this setting. When in this display you may adjust the Bass, Mid and This compass is self-calibrating, which eliminates the Treble settings. Adjust the settings with the “+” and “–” need to manually reset the compass.
Page 358 356 UNDERSTANDING YOUR INSTRUMENT PANEL • Surround Sound — If Equipped Phone/Bluetooth® After touching the “Phone/Bluetooth®” soft-key the This feature provides simulated surround sound mode. following settings will be available: To make your selection, touch the “Surround Sound” soft-key, select On or Off followed by pressing the back •...
Page 359 UNDERSTANDING YOUR INSTRUMENT PANEL 357 your selection, touch the “Channel Skip” soft-key, select NOTE: SiriusXM Travel Link is a separate subscription the channels you would like to skip followed by pressing and is available for U.S. residents only. the back arrow soft-key. •...
Page 360: Uconnect® Radios - If Equipped
358 UNDERSTANDING YOUR INSTRUMENT PANEL Clear Personal Data iPod®/USB/MP3 CONTROL — IF EQUIPPED After touching the “Clear Personal Data Settings” soft- Located in the lower section of the front integrated center key the following settings will be available: stack, in front of the rotary shifter, this feature allows an iPod®...
Page 361: Uconnect® Rear Seat Entertainment System - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 359 iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® Getting Started and iPhone® devices. Some iPod® software versions • Screen(s) located in the rear of front seats: Open the may not fully support the iPod® control features. Please LCD screen cover by lifting up on cover.
Page 362 360 UNDERSTANDING YOUR INSTRUMENT PANEL • Cycle the ignition to the ON or ACC position. • Your vehicle may be equipped with a Blu-ray™ Disc Player. If equipped with a Blu-ray™ Disc Player, the icon will be present on the Player. •...
Page 363 UNDERSTANDING YOUR INSTRUMENT PANEL 361 Rear Seat Entertainment System Remote Control Rear Seat Entertainment System Headphone Channel Channel Selector Selector • The system can be controlled by the front seat occu- pants utilizing either the touchscreen radio, or by the rear seat occupants using the remote control.
Page 364: Dual Video Screen
362 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Video Screen NOTE: Typically there are two different ways to operate the features of the Rear Seat Entertainment System. • The Remote Control • The Touchscreen Radio (If Equipped) Blu-ray™ Disc Player Play A Blu-ray™ Disc The Blu-ray™...
Page 365: Play Video Games
UNDERSTANDING YOUR INSTRUMENT PANEL 363 • Press the Media soft-key, then touch the Rear Media To view a Blu-ray™ insert the disc into the Blu-ray™ Disc Player. Playback will begin automatically after the Blu- soft key. ray™ Disc is recognized by the disc drive. If playback •...
Page 366: Play A Dvd/Blu-Ray™ Disc Using The Touchscreen Radio
364 UNDERSTANDING YOUR INSTRUMENT PANEL When connecting an external source to the AUX/HDMI input, ensure to follow the standard color coding for the audio/video jacks: 1. HDMI Input 2. Right audio in (red) 3. Left audio in (white) 4. Video in (yellow) NOTE: Certain high-end video games, such as Playsta- tion4 and XBox One will exceed this power limit of the vehicle’s Power Inverter.
Page 367 UNDERSTANDING YOUR INSTRUMENT PANEL 365 radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen or starts playing the first track. 2. To watch a DVD/Blu-ray™ Disc on Rear 1 (driver’s side rear passenger) ensure the Remote Control and Headphone channel selector switch is on Rear 1.
Page 368 366 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the Rear Media soft-key to display the Rear Media Control screen. Rear Seat Entertainment Source Screen NOTE: Touching the screen on a Touchscreen radio while a DVD or Blu-ray™ Disc is playing, brings up the basic Rear Media Control Screen remote control functions for DVD play such as scene 3.
Page 369: Important Notes For Dual Video Screen System
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Important Notes For Dual Video Screen System Blu-ray™ Disc Player Remote Control — If Equipped • The Rear Seat Entertainment System is able to transmit two channels of stereo audio and video simultane- ously. • The Blu-ray™ Disc Player can play CDs, DVDs and Blu-ray™...
Page 370 368 UNDERSTANDING YOUR INSTRUMENT PANEL Controls And Indicators — Press to navigate menus. 1. Power — Turns the screen and wireless headphone 6. SETUP — Press to access the screen settings menu. transmitter for the selected Channel on or off. To hear —...
Page 371: Replacing The Remote Control Batteries
UNDERSTANDING YOUR INSTRUMENT PANEL 369 — Press and hold to fast rewind through the Replacing The Remote Control Batteries current audio track or video chapter. The remote control requires two AAA batteries for op- eration. To replace the batteries: 14. Mutes headphone audio. •...
Page 372: Headphones Operation
370 UNDERSTANDING YOUR INSTRUMENT PANEL Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. If no audio is heard after increasing the volume control, verify that the screen is turned on, the channel is not muted and the headphone channel selector switch is on the desired channel.
Page 373: Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 371 Controls NOTE: • When both the headphone and the remote control The headphone power indicator and controls are located channel selector switches are on Channel 1, the on the right ear cup. Remote is controlling Channel 1 and the headphones NOTE: The rear video system must be turned on before are tuned to the audio on Channel 1.
Page 374: Replacing The Headphone Batteries
372 UNDERSTANDING YOUR INSTRUMENT PANEL 5. To cancel out of the Mode Selection menu, press the particular Unwired Technology LLC ( Unwired ) wire- BACK button on the remote control. less headphone ( Product ). The warranty is not transfer- able.
Page 375 UNDERSTANDING YOUR INSTRUMENT PANEL 373 FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, If you have any questions or comments regarding your INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, PU- Unwired® wireless headphones, please phone 1-888-293-3332 NITIVE OR OTHER DAMAGES OF ANY KIND OR or email customersupport@unwiredtechnology.com. NATURE WHATSOEVER.
Page 376 374 UNDERSTANDING YOUR INSTRUMENT PANEL Display Settings Display Settings menu. These settings control the appear- ance of the video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change these settings under normal circum- stances.
Page 377 UNDERSTANDING YOUR INSTRUMENT PANEL 375 Listening To Audio With The Screen Closed the remote control’s power button to turn audio on. If audio is still not heard, check that fully charged batteries To listen to only audio portion of the channel with the are installed in the headphones.
Page 378 376 UNDERSTANDING YOUR INSTRUMENT PANEL match in order for the disc to play. If the region code for also play DVD-Video content recorded to a DVD-R or the DVD disc does not match the region code for the DVD-RW disc. DVD-ROM discs (either pressed or re- player, the disc will not play.
Page 379 UNDERSTANDING YOUR INSTRUMENT PANEL 377 • For CD Data (or CD-ROM) discs, always use the Compressed Audio Files (MP3 and WMA) ISO-9660 (Level 1 or Level 2), Joliet, or Romeo format. The Blu-ray™ Disc player is capable of playing MP3 Other formats (such as UDF, HFS, or others) are not (MPEG-1 Audio Layer 3) and WMA (Windows Media supported.
Page 380 378 UNDERSTANDING YOUR INSTRUMENT PANEL • Other compression formats such as AAC, MP3 Pro, Radio displays. A dirty, damaged, or incompatible disc Ogg Vorbis, and ATRAC3 will not play. The Blu-ray™ format are all potential causes for a Disc Error message. player will automatically skip the file and begin play- If a disc has a damaged track which results in audible or ing the next available file.
Page 381: Steering Wheel Audio Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 379 Product Agreement General Information This product incorporates copyright protection technol- This system complies with Part 15 of the FCC Operation ogy that is protected by U.S. patents and other intellec- is subject to the following two conditions: tual property rights.
Page 382: Radio Operation
380 UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the center button will make the radio switch between the various modes available (AM/FM/SXM/ CD/AUX/VES, etc.). The left-hand control is a rocker-type switch with a push-button in the center. The function of the left-hand control is different depending on which mode you are in.
Page 383: Cd Player
UNDERSTANDING YOUR INSTRUMENT PANEL 381 CD Player 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once 4.
Page 384: Radio Operation And Mobile Phones
382 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND MOBILE PHONES CLIMATE CONTROLS Under certain conditions, the mobile phone being on in The air conditioning and heating system is designed to your vehicle can cause erratic or noisy performance from make you comfortable in all types of weather. This your radio.
Page 385: General Overview
UNDERSTANDING YOUR INSTRUMENT PANEL 383 General Overview Soft-Keys Hard-Keys Soft-keys are accessible on the Uconnect® system screen. The hard-keys are located below the Uconnect® screen. Uconnect® 5.0 Automatic Temperature Controls — Soft-Keys Automatic Climate Controls — Hard-Keys...
Page 386 384 UNDERSTANDING YOUR INSTRUMENT PANEL this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. 2. A/C Button Press and release to change the current setting, the indicator illuminates when A/C is ON. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
Page 387 UNDERSTANDING YOUR INSTRUMENT PANEL 385 5. Front Defrost Button CAUTION! Press and release to change the current airflow setting to Failure to follow these cautions can cause damage to Defrost mode. The indicator illuminates when this fea- the heating elements: ture is ON.
Page 388 386 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Rear Climate Button — If Equipped settings or on the touchscreen, press and slide the soft- key temperature bar towards the blue arrow soft-key for Press and release this button to turn on the rear climate cooler temperature settings.
Page 389 UNDERSTANDING YOUR INSTRUMENT PANEL 387 • Panel Mode automatic mode to switch to manual operation. The speeds can be selected using either hard-keys or soft-keys Air comes from the outlets in the instrument as follows: panel. Each of these outlets can be individu- ally adjusted to direct the flow of air.
Page 390 388 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor Mode NOTE: In Sync mode, this button will also automatically adjust the passenger temperature setting at the same Air comes from the floor outlets. A slight time. amount of air is directed through the defrost and side window demister outlets.
Page 391: Climate Control Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 389 • If your air conditioning performance seems lower than the temperature bar into the red area, indicates warmer temperatures. Moving the temperature bar into the blue expected, check the front of the A/C condenser (lo- area indicates cooler temperatures.
Page 392: Automatic Temperature Control (Atc)
390 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Automatic Temperature Control (ATC) Automatic Operation When outside air contains smoke, odors, or 1. Press the AUTO hard-key or soft-key button on the high humidity, or if rapid cooling is desired, Automatic Temperature Control (ATC) Panel. you may wish to recirculate interior air by pressing the Recirculation control button.
Page 393 UNDERSTANDING YOUR INSTRUMENT PANEL 391 NOTE: Manual Operation Override • It is not necessary to move the temperature settings for The system allows for manual selection of blower speed, air distribution mode, A/C status and recirculation con- cold or hot vehicles. The system automatically adjusts trol.
Page 394: Equipped
392 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Automatic Temperature Control (ATC) — If Equipped The rear ATC system has floor air outlets at the rear right side of the 3rd Row seats and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 395 UNDERSTANDING YOUR INSTRUMENT PANEL 393 Controlling The Rear Climate Controls From The Front ATC Panel The Three-Zone ATC system allows for adjustment of the rear climate controls from the front ATC panel. To change the rear system settings: • Press REAR button to change control to rear control mode, Rear display will appear.
Page 396 394 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Lock Pressing the Rear Temperature Lock soft-key on the Uconnect® touchscreen, illuminates a lock symbol in the rear display. The rear temperature and air source are controlled from the front Uconnect® system. Rear second row occupants can only adjust the rear ATC control when the Rear Temperature Lock button is turned off.
Page 397 UNDERSTANDING YOUR INSTRUMENT PANEL 395 • Rotate the Rear Blower, Rear Temperature and the Only when the Rear Control Icon is illuminated do the Rear Mode Control knobs to suit your comfort needs. second row seat occupants have control of the rear blower speed.
Page 398 396 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control Bi-Level Mode Only when the Rear Control Icon is illuminated do the Air comes from both the headliner outlets and the second row seat occupants have control of the rear floor outlets. temperature control knob.
Page 399 UNDERSTANDING YOUR INSTRUMENT PANEL 397 A solution of 50% OAT (Organic Additive Technology) Window Fogging coolant that meets the requirements of Chrysler Material Interior fogging on the windshield can be quickly re- Standard MS-12106 and 50% water is recommended. moved by turning the mode selector to Defrost. The Refer to “Maintenance Procedures”...
Page 400 398 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake A/C Air Filter Make sure the air intake, located directly in front of the The climate control system filters outside air containing windshield, is free of obstructions such as leaves. Leaves dust, pollen and some odors. Strong odors cannot be collected in the air intake may reduce airflow, and if they totally filtered out.
Page 401 UNDERSTANDING YOUR INSTRUMENT PANEL 399 Control Setting Suggestions For Various Weather Conditions...
Page 403: Starting And Operating
STARTING AND OPERATING CONTENTS ▫ Key Ignition Park Interlock....414 STARTING PROCEDURES ....406 ▫...
Page 404 402 STARTING AND OPERATING ON-ROAD DRIVING TIPS ....431 FUEL SAVER TECHNOLOGY 5.7L ENGINE ONLY — IF EQUIPPED ..... . .439 OFF-ROAD DRIVING TIPS .
Page 405 STARTING AND OPERATING 403 ▫ ESC Activation/Malfunction Indicator Light And ▫ Run Flat Tires — If Equipped ... . .469 ESC OFF Indicator Light ....452 ▫...
Page 406 404 STARTING AND OPERATING ▫ General Information ....486 ▫ E-85 General Information ....492 ▫...
Page 407 STARTING AND OPERATING 405 TRAILER TOWING .....501 SNOW PLOW ......516 ▫...
Page 408: Starting Procedures
406 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave the Key Fob in or near the vehicle (or inside and outside mirrors, fasten your seat belt, and if in a location accessible to children), and do not present, instruct all other occupants to buckle their seat leave the ignition of a vehicle equipped with...
Page 409: Keyless Enter-N-Go
STARTING AND OPERATING 407 Do not press the accelerator. Use the Fob with Integrated CAUTION! Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The Damage to the transmission may occur if the follow- starter motor will continue to run, and it will disengage ing precautions are not observed: •...
Page 410: Normal Starting
408 STARTING AND OPERATING Normal Starting To Turn Off The Engine Using ENGINE START/STOP Button Using The ENGINE START/STOP Button 1. Place the shift lever/gear selector in PARK, then press 1. The transmission must be in PARK. and release the ENGINE START/STOP button. 2.
Page 411: Extreme Cold Weather (Below -20°F Or −29°C)
STARTING AND OPERATING 409 • Press the ENGINE START/STOP button a second time NOTE: If the ignition switch is left in the ACC or RUN (engine not running) position and the transmission is in to place the ignition to the RUN position (EVIC will PARK, the system will automatically time out after 30 display “ON/RUN”), minutes of inactivity and the ignition will switch to the...
Page 412: If Engine Fails To Start
410 STARTING AND OPERATING If Engine Fails To Start WARNING! (Continued) • If the vehicle has a discharged battery, booster WARNING! cables may be used to obtain a start from a booster • Never pour fuel or other flammable liquid into the battery or the battery in another vehicle.
Page 413: After Starting
STARTING AND OPERATING 411 3. Press and release the ENGINE START/STOP button The engine block heater cord is located: once. • 3.6L Engine — Coiled and strapped to the engine oil dipstick tube. The starter motor will engage automatically, run for 10 seconds, and then disengage.
Page 414: Automatic Transmission
412 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! (Continued) • Unintended movement of a vehicle could injure WARNING! those in or near the vehicle. As with all vehicles, • It is dangerous to shift out of PARK or NEUTRAL you should never exit a vehicle while the engine is if the engine speed is higher than idle speed.
Page 415 STARTING AND OPERATING 413 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with Damage to the transmission may occur if the follow- access to an unlocked vehicle. Allowing children to ing precautions are not observed: be in a vehicle unattended is dangerous for a •...
Page 416: Key Ignition Park Interlock
414 STARTING AND OPERATING Key Ignition Park Interlock Fuel Economy (ECO) Mode This vehicle is equipped with a Key Ignition Park Inter- The Fuel Economy (ECO) mode can improve the vehi- lock which requires the transmission to be in PARK cle’s overall fuel economy during normal driving condi- before the engine can be turned off.
Page 417: Eight-Speed Automatic Transmission
STARTING AND OPERATING 415 • The overall driving performance will be more conser- vative. • Some ECO mode functions may be temporarily inhib- ited based on temperature and other factors. Eight-Speed Automatic Transmission The transmission is controlled using a rotary electronic gear selector located on the center console.
Page 418 416 STARTING AND OPERATING The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers).
Page 419 STARTING AND OPERATING 417 NOTE: After selecting any gear range, wait a moment to WARNING! allow the selected gear to engage before accelerating. • Never use the PARK position as a substitute for the This is especially important when the engine is cold. parking brake.
Page 420 418 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 421 STARTING AND OPERATING 419 The following indicator should be used to ensure that CAUTION! you have engaged the transmission into the PARK posi- • Before moving the gear selector out of PARK, you tion: must start the engine and also press the brake •...
Page 422 420 STARTING AND OPERATING DRIVE (D) WARNING! This range should be used for most city and highway Do not coast in NEUTRAL and never turn off the driving. It provides the smoothest upshifts and down- ignition to coast down a hill. These are unsafe shifts, and the best fuel economy.
Page 423 STARTING AND OPERATING 421 During cold temperatures, transmission operation may illuminated. A message in the instrument cluster will be modified depending on engine and transmission inform the driver of the more serious conditions, and temperature as well as vehicle speed. This feature im- indicate what actions may be necessary.
Page 424 422 STARTING AND OPERATING 5. Restart the engine. system can also provide you with more control during passing, city driving, cold slippery conditions, mountain 6. Shift into the desired gear range. If the problem is no driving, trailer towing, and many other situations. longer detected, the transmission will return to normal operation.
Page 425 STARTING AND OPERATING 423 • The system will ignore attempts to upshift at too low result. It will remain in the selected gear until another upshift or downshift is chosen, except as described of a vehicle speed. below. • Holding the (-) paddle depressed will downshift the •...
Page 426: All-Wheel Drive Operation
424 STARTING AND OPERATING NOTE: This system is not appropriate for conditions WARNING! where LOW range is recommended. Refer to “Off-Road Driving Tips” in “Starting and Operating” for further Do not downshift for additional engine braking on a information. slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or Electronically Shifted Transfer Case personal injury.
Page 427 STARTING AND OPERATING 425 This electronically shifted transfer case is designed to be driven in the AWD AUTO position for normal street and highway conditions on dry hard surfaced roads. For variable driving conditions, the AWD AUTO mode can be used. In this mode, the front axle is engaged, but the vehicle’s power is sent to the rear wheels.
Page 428 426 STARTING AND OPERATING Transfer Case Position Indicator Messages If One Or More Shift Conditions Are Not Met: The Transfer Case Position Indicator messages (AWD 1. The indicator light for the current position will remain AUTO and LOW RANGE) are located in the EVIC (Electronic Vehicle Information Center) and indicate the 2.
Page 429 STARTING AND OPERATING 427 that the all-wheel drive system is not functioning prop- Proper operation of all-wheel drive vehicles depends on erly and that service is required. tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the WARNING! transfer case.
Page 430: Shifting Procedure
428 STARTING AND OPERATING For additional information on the appropriate use of each Neutral (N) transfer case mode position, see the information below: Neutral – This range disengages both the front and rear AWD Auto driveshafts from the powertrain. To be used for flat towing behind another vehicle.
Page 431 STARTING AND OPERATING 429 • If all the requirements to select a new transfer case 2. Shift the transmission into NEUTRAL. position have been met, the current position indicator 3. While still rolling, rotate the AWD control switch to light will turn OFF, the selected position indicator light the desired position.
Page 432 430 STARTING AND OPERATING NOTE: NEUTRAL Shift Procedure • If Steps 1 or 2 of either the Preferred or Alternate 1. Bring the vehicle to a complete stop with the engine Procedure are not satisfied prior to attempting the shift running.
Page 433: On-Road Driving Tips
STARTING AND OPERATING 431 NOTE: If shift conditions/interlocks are not met, a “To Tow Vehicle Safely, Read Neutral Shift Procedure in Owners Manual” message will flash from the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel”...
Page 434: Off-Road Driving Tips
432 STARTING AND OPERATING turns or abrupt maneuvers. As with other vehicles of this CAUTION! (Continued) type, failure to operate this vehicle correctly may result in allow for differential action between the front to rear loss of control or vehicle rollover. driveshafts.
Page 435: Driving In Snow, Mud And Sand
STARTING AND OPERATING 433 Driving through water more than a few inches/ Standing Water centimeters deep will require extra caution to ensure Avoid driving in standing water deeper than 20 in (51 safety and prevent damage to your vehicle. If you must cm), and reduce speed appropriately to minimize wave drive through water, try to determine the depth and the effects.
Page 436: Hill Climbing
434 STARTING AND OPERATING to “All-Wheel Drive Operation” in “Starting and Oper- and shift into REVERSE. Back slowly down the hill, ating” for further information. Do not shift to a lower allowing the compression braking of the engine to help gear than necessary to maintain forward motion.
Page 437: Traction Downhill
STARTING AND OPERATING 435 by turning the front wheels slowly. This may provide a always a good idea to check for damage. That way you fresh “bite” into the surface and will usually provide can get any problems taken care of right away and have traction to complete the climb.
Page 438: Power Steering
436 STARTING AND OPERATING • After extended operation in mud, sand, water, or POWER STEERING similar dirty conditions, have the radiator, fan, brake 3.6L Engine rotors, wheels, brake linings, and axle yokes inspected Your vehicle is equipped with an electro-hydraulic power and cleaned as soon as possible.
Page 439: L Engine
STARTING AND OPERATING 437 NOTE: If the “SERVICE POWER STEERING” message • Even if power steering assistance is no longer opera- and a flashing icon are displayed on the EVIC screen, it indicates that the vehicle needs to be tional, it is still possible to steer the vehicle. Under taken to the dealer for service.
Page 440: Power Steering Fluid Check
438 STARTING AND OPERATING If for some reason the power assist is interrupted, it will WARNING! still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering Continued operation with reduced power steering effort, especially at very low vehicle speeds and during assist could pose a safety risk to yourself and others.
Page 441: Fuel Saver Technology 5.7L Engine Only - If Equipped
STARTING AND OPERATING 439 apparent, and/or the system is not functioning as antici- If necessary, add fluid to restore to the proper indicated pated. Coordinate inspection efforts through an autho- level. With a clean cloth, wipe any spilled fluid from all rized dealer.
Page 442 440 STARTING AND OPERATING The foot operated parking brake is located below the When the parking brake is applied with the ignition lower left corner of the instrument panel. To apply the switch in the ON position, the “Brake Warning Light” in park brake, firmly push the park brake pedal fully.
Page 443 STARTING AND OPERATING 441 make it difficult to move the gear selector out of PARK. WARNING! (Continued) The parking brake should always be applied whenever • Never leave children alone in a vehicle, or with the driver is not in the vehicle. access to an unlocked vehicle.
Page 444: Electronic Brake Control System
442 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Do not leave the Key Fob in or near the vehicle or If the “Brake Warning Light” remains on with the in a location accessible to children, and do not parking brake released, a brake system malfunction leave the ignition of a vehicle equipped with is indicated.
Page 445: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 443 Anti-Lock Brake System (ABS) Traction Control System (TCS) This system aids the driver in maintaining vehicle control This system monitors the amount of wheel spin of each of under adverse braking conditions. The system controls the driven wheels. If wheel spin is detected, brake hydraulic brake pressure to prevent wheel lock-up and pressure is applied to the slipping wheel(s) and engine help avoid skidding on slippery surfaces during braking.
Page 446: Brake Assist System (Bas)
444 STARTING AND OPERATING Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking • The BAS cannot prevent the natural laws of phys- capability during emergency braking maneuvers. The ics from acting on the vehicle, nor can it increase system detects an emergency braking situation by sens- the traction afforded by prevailing road conditions.
Page 447: Electronic Stability Control (Esc)
STARTING AND OPERATING 445 applies the appropriate brake and may also reduce WARNING! (Continued) engine power to lessen the chance that wheel lift will or other vehicles. The capabilities of an ERM- occur. ERM will only intervene during very severe or equipped vehicle must never be exploited in a reck- evasive driving maneuvers.
Page 448 446 STARTING AND OPERATING the intended path, ESC applies the brake of the appro- WARNING! priate wheel to assist in counteracting the oversteer or understeer condition. Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, •...
Page 449 STARTING AND OPERATING 447 AUTO Range (All-Wheel Drive Models) Or features of ESC function normally. This mode is intended Two-Wheel Drive Models to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than ESC would nor- mally allow is required to gain traction.
Page 450: Trailer Sway Control (Tsc)
448 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving WARNING! (Continued) with snow chains, or starting off in deep snow, sand, or • Trailer Sway control (TSC) is disabled when the gravel, it may be desirable to switch to the “Partial Off” ESC system is in the “Partial Off”...
Page 451: Hill Start Assist (Hsa)
STARTING AND OPERATING 449 will become active automatically once an excessively Hill Start Assist (HSA) swaying trailer is recognized. Note that TSC cannot stop The HSA system is designed to assist the driver when all trailers from swaying. Always use caution when starting a vehicle from a stop on a hill.
Page 452 450 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle back- HSA will provide assistance when starting on a grade ing uphill is in REVERSE gear). when pulling a trailer. HSA will work in REVERSE and all forward gears when WARNING! the activation criteria have been met.
Page 453: Ready Alert Braking
STARTING AND OPERATING 451 Ready Alert Braking WARNING! (Continued) Ready Alert Braking may reduce the time required to • HSA is not a parking brake. Always apply the reach full braking during emergency braking situations. parking brake fully when leaving your vehicle. It anticipates when an emergency braking situation may Also, be certain to leave the transmission in PARK.
Page 454: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
452 STARTING AND OPERATING function in the intermittent mode. When Rain Brake The “ESC Activation/Malfunction Indicator Light” (lo- Support is active, there is no notification to the driver and cated in the instrument cluster) starts to flash as soon as no driver interaction is required.
Page 455: Tire Safety Information
STARTING AND OPERATING 453 • The ESC system will make buzzing or clicking sounds TIRE SAFETY INFORMATION when it is active. This is normal; the sounds will stop Tire Markings when ESC becomes inactive following the maneuver that caused the ESC activation. The “ESC OFF Indicator Light”...
Page 456 454 STARTING AND OPERATING • Temporary spare tires are designed for temporary NOTE: emergency use only. Temporary high pressure com- • P (Passenger) — Metric tire sizing is based on U.S. pact spare tires have the letter “T” or “S” molded into design standards.
Page 457 STARTING AND OPERATING 455 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 458 456 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions –...
Page 459: Tire Identification Number (Tin)
STARTING AND OPERATING 457 EXAMPLE: Light Load (LL) = Light load tire C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load – Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure –...
Page 460 458 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 461: Tire Terminology And Definitions
STARTING AND OPERATING 459 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after Cold Tire Inflation Pressure the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 462: Tire Loading And Tire Pressure
460 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 463 STARTING AND OPERATING 461 3. Tire size designed for your vehicle. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of 4. Cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires.
Page 464 462 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 465 STARTING AND OPERATING 463...
Page 466: Tires - General Information
464 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 467: Tire Inflation Pressures
STARTING AND OPERATING 465 stability of the vehicle and can produce a feeling of WARNING! (Continued) sluggish response or over responsiveness in the steering. • Unequal tire pressures from one side of the vehicle NOTE: to the other can cause the vehicle to drift to the right or left.
Page 468 466 STARTING AND OPERATING judgement when determining proper inflation. Tires Check tire pressures more often if subject to a wide range may look properly inflated even when they are under- of outdoor temperatures, as tire pressures vary with inflated. temperature changes. •...
Page 469: Tire Pressures For High Speed Operation
STARTING AND OPERATING 467 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 470: Tire Types
468 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
Page 471: Run Flat Tires - If Equipped
STARTING AND OPERATING 469 If you need snow tires, select tires equivalent in size and Run Flat Tires — If Equipped type to the original equipment tires. Use snow tires only Run Flat tires allow you the capability to drive 50 miles in sets of four;...
Page 472: Spare Tires - If Equipped
470 STARTING AND OPERATING Spare Tires — If Equipped rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT”...
Page 473 STARTING AND OPERATING 471 Do not install a wheel cover or attempt to mount a front or rear axle of your vehicle, but it is not. This spare conventional tire on the compact spare wheel, since the tire may have limited tread life. When the tread is worn wheel is designed specifically for the compact spare tire.
Page 474: Tire Spinning
472 STARTING AND OPERATING Refer to “Freeing A Stuck Vehicle” in “What To Do In WARNING! Emergencies” for further information. Limited-use spares are for emergency use only. In- WARNING! stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the Fast spinning tires can be dangerous.
Page 475: Life Of Tire
STARTING AND OPERATING 473 tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further infor- mation. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: •...
Page 476: Replacement Tires
474 STARTING AND OPERATING Information placard or the Vehicle Certification Label for WARNING! the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original Tires and the spare tire should be replaced after six equipment tire sidewall.
Page 477: Tire Chains (Traction Devices)
STARTING AND OPERATING 475 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 478 476 STARTING AND OPERATING • Install on Rear Tires Only CAUTION! (Continued) • Due to limited clearance, the THULE XG-12 PRO • Because of restricted traction device clearance be- traction device or equivalent is recommended on tween tires and other suspension components, it is P265/60R18 or 265/50R20 tires.
Page 479: Tire Rotation Recommendations
STARTING AND OPERATING 477 These effects can be reduced by timely rotation of tires. CAUTION! (Continued) The benefits of rotation are especially worthwhile with • Observe the traction device manufacturer’s instruc- aggressive tread designs such as those on On/Off-Road tions on the method of installation, operating type tires.
Page 480: Tire Pressure Monitor System (Tpms)
478 STARTING AND OPERATING NOTE: It is particularly important, for you to regularly check the tire pressure in all of your tires and to maintain the proper pressure. The Tire Pressure Monitor System (TPMS) consists of the following components: • Receiver Module •...
Page 481 STARTING AND OPERATING 479 the outside temperature decreases, the tire pressure will cold tire placard pressure. Once the low tire pressure decrease. Tire pressure should always be set based on warning has been illuminated, the tire pressure must be cold inflation tire pressure. This is defined as the tire increased to the recommended cold tire pressure in order pressure after the vehicle has not been driven for at least for the Tire Pressure Monitoring Telltale Light to be...
Page 482 480 STARTING AND OPERATING Light will still be ON. In this situation, the Tire Pressure CAUTION! (Continued) Monitoring Telltale Light will turn OFF only after the • After inspecting or adjusting the tire pressure al- tires have been inflated to the vehicle’s recommended ways reinstall the valve stem cap.
Page 483: Premium System - If Equipped
STARTING AND OPERATING 481 Under-inflation also reduces fuel efficiency and tire monitor tire pressure levels. Sensors, mounted to each tread life, and may affect the vehicle’s handling and wheel as part of the valve stem, transmit tire pressure stopping ability. readings to the Receiver Module.
Page 484: Tire Pressure Monitoring Low Pressure Warnings
482 STARTING AND OPERATING The Tire Pressure Monitor System (TPMS) consists of the Tire Pressure Monitoring Low Pressure Warnings following components: • Receiver Module The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an au- • Four Tire Pressure Monitoring Sensors dible chime will be activated, when one or more of the •...
Page 485: Service Tpm System Warning
STARTING AND OPERATING 483 The system will automatically update, the graphic dis- play of the pressure value(s) will return to its original color and the Tire Pressure Monitoring Telltale Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- mation.
Page 486 484 STARTING AND OPERATING If the ignition switch is cycled, this sequence will repeat, 4. Using tire chains on the vehicle. providing the system fault still exists. If the system fault 5. Using wheels/tires not equipped with TPM sensors. no longer exists, the Tire Pressure Monitoring Telltale The EVIC will also display a SERVICE TPM SYSTEM Light will no longer flash, the SERVICE TPM SYSTEM message for a minimum of five seconds when a system...
Page 487 STARTING AND OPERATING 485 NOTE: There is no tire pressure monitoring sensor in the play dashes (- -) in place of the pressure value. Once you spare tire. The TPMS will not be able to monitor the tire repair or replace the original road tire, and reinstall it on pressure.
Page 488: Fuel Requirements
486 STARTING AND OPERATING General Information FUEL REQUIREMENTS This device complies with Part 15 of the FCC rules and 3.6L Engine — If Equipped RSS 210 of Industry Canada. Operation is subject to the following conditions: This engine is designed to meet all emis- •...
Page 489: Reformulated Gasoline
STARTING AND OPERATING 487 an octane range of 87 to 89. The manufacturer recom- Reformulated Gasoline mends the use of 89 octane for optimum performance. Many areas of the country require the use of cleaner The use of premium gasoline is not recommended, as it burning gasoline referred to as “Reformulated Gasoline.”...
Page 490: E-85 Usage In Non-Flex Fuel Vehicles
488 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles CAUTION! Non-Flex Fuel Vehicles (FFV) are compatible with gaso- DO NOT use gasoline containing Methanol or gaso- line containing 10% ethanol (E10). Gasoline with higher line containing more than 10% Ethanol. Use of these ethanol content may void the New Vehicle Limited blends may result in starting and drivability prob- Warranty.
Page 491: Mmt In Gasoline
STARTING AND OPERATING 489 To fix a Non-FFV vehicle inadvertently fueled once with without MMT be used in your vehicle. The MMT content E-85 perform the following: of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether •...
Page 492: Fuel System Cautions
490 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentrations performance: of methanol.
Page 493: Carbon Monoxide Warnings
STARTING AND OPERATING 491 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 494: Flexible Fuel (3.6L Engine Only) - If Equipped
492 STARTING AND OPERATING FLEXIBLE FUEL (3.6L ENGINE ONLY) — IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel ve- hicles only. These vehicles can be identified by a unique fuel filler door label that states Ethanol (E-85) or Un- leaded Gasoline Only.
Page 495: Fuel Requirements
STARTING AND OPERATING 493 When you do switch fuel types it is recommended that: WARNING! • You do not add less than 5 gallons (19 Liters) when Ethanol vapors are extremely flammable and could refueling. cause serious personal injury. Never have any smok- •...
Page 496: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
494 STARTING AND OPERATING engine. To eliminate driveability issues that may be Starting caused by these deposits, a supplemental gasoline The characteristics of E-85 fuel make it unsuitable for use additive, such as MOPAR® Injector Cleanup or when ambient temperatures fall below 0°F (-18°C). In the Techron may be used.
Page 497: Replacement Parts
STARTING AND OPERATING 495 Replacement Parts ADDING FUEL Many components in your Flexible Fuel Vehicle (FFV) are 1. Press the fuel filler door release switch (located under designed to be compatible with ethanol. Always be sure the headlamp switch). that your vehicle is serviced with correct ethanol com- patible parts.
Page 498 496 STARTING AND OPERATING 2. Open the fuel filler door. 3. There is no fuel filler cap. A flapper door inside the pipe seals the system. 4. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper door while refuel- ing.
Page 499 STARTING AND OPERATING 497 • Insert funnel into same filler pipe opening as the fuel WARNING! nozzle. • Never have any smoking materials lit in or near the • Ensure funnel is inserted fully to hold flapper door vehicle when the fuel door is open or the tank is open.
Page 500: Emergency Fuel Filler Door Release
498 STARTING AND OPERATING Emergency Fuel Filler Door Release If you are unable to open the fuel filler door, use the fuel filler door emergency release. 1. Open the liftgate. 2. Push the inboard edge of the left storage bin to the center, this will pop up the outboard edge.
Page 501: Vehicle Loading
STARTING AND OPERATING 499 VEHICLE LOADING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Certification Label Payload As required by National Highway Traffic Safety Admin- istration regulations, your vehicle has a certification label The payload of a vehicle is defined as the allowable load affixed to the driver’s side door or pillar.
Page 502 500 STARTING AND OPERATING Tire Size values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are The tire size on the Vehicle Certification Label represents added. the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Page 503: Trailer Towing
STARTING AND OPERATING 501 items down low and be sure that the weight is distributed TRAILER TOWING equally. Stow all loose items securely before driving. In this section you will find safety tips and information on limits to the type of towing you can reasonably do Improper weight distributions can have an adverse effect with your vehicle.
Page 504 502 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle WARNING! (Continued) Certification Label” in “Starting and Operating” for you use a standard weight-carrying hitch, you could further information. lose control of your vehicle and cause a collision. Gross Trailer Weight (GTW) Gross Combination Weight Rating (GCWR) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem-...
Page 505 STARTING AND OPERATING 503 Trailer Sway Control WARNING! The trailer sway control can be a mechanical telescoping It is important that you do not exceed the maximum link that can be installed between the hitch receiver and front or rear GAWR. A dangerous driving condition the trailer tongue that typically provides adjustable fric- can result if either rating is exceeded.
Page 506 504 STARTING AND OPERATING Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted Weight Distributing Hitch age through spring (load) bars. They are typically used system may reduce handling, stability, braking for heavier loads to distribute trailer tongue weight to the performance, and could result in a collision.
Page 507: Trailer Hitch Classification
STARTING AND OPERATING 505 Trailer Hitch Classification Trailer Hitch Classification Definitions The following chart provides the industry standard for Class Max. Trailer Hitch In- the maximum trailer weight a given trailer hitch class can dustry Standards tow and should be used to assist you in selecting the Class I - Light Duty 2,000 lbs (907 kg) correct trailer hitch for your intended towing condition.
Page 508: Trailer Towing Weights (Maximum Trailer Weight Ratings)
506 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Max. GTW Max. Trailer Engine Model Combined Wt. Frontal Area (Gross Trailer Tongue Wt. (See Rating) Wt.) Note)
Page 509: Trailer Hitch Receiver Cover Removal - If Equipped
STARTING AND OPERATING 507 NOTE: Trailer Hitch Receiver Cover Removal — If Equipped • The trailer tongue weight must be considered as part Your vehicle may be equipped with a trailer hitch re- of the combined weight of occupants and cargo, and ceiver cover, this must be removed to access the trailer should never exceed the weight referenced on the Tire hitch receiver (if equipped).
Page 510 508 STARTING AND OPERATING Hitch Receiver Cover Retainers Hitch Receiver Cover To reinstall the cover after towing repeat the procedure in 1 — Hitch Receiver Cover reverse order. 2 — Locking Retainer NOTE: Be sure to engage all tabs of the hitch receiver 2.
Page 511: Trailer And Tongue Weight
STARTING AND OPERATING 509 Trailer And Tongue Weight Always load a trailer with 60% of the weight in the front of the trailer. This places 10% of the GTW on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer.
Page 512: Towing Requirements
510 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options or dealer-installed options must trailer is towed, do not drive over 50 mph (80 km/h) be considered as part of the total load on your vehicle.
Page 513 STARTING AND OPERATING 511 WARNING! (Continued) WARNING! (Continued) • Vehicles with trailers should not be parked on a • Make certain that the load is secured in the trailer grade. When parking, apply the parking brake on and will not shift during travel. When trailering the tow vehicle.
Page 514 512 STARTING AND OPERATING Towing Requirements — Tires tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the • Do not attempt to tow a trailer while using a compact vehicle’s GVWR and GAWR limits. spare tire.
Page 515 STARTING AND OPERATING 513 WARNING! CAUTION! (Continued) could lead to accelerated brake lining wear, higher • Do not connect trailer brakes to your vehicle’s brake pedal effort, and longer stopping distances. hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have Towing Requirements —...
Page 516 514 STARTING AND OPERATING Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 517: Towing Tips
STARTING AND OPERATING 515 Towing Tips AutoStick® • When using the AutoStick® shift control, select the Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy highest gear that allows for adequate performance and traffic.
Page 518: Snow Plow
516 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to SNOW PLOW maximize fuel efficiency. Snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The Cooling System airbag crash sensors may be affected by the change in the To reduce potential for engine and transmission over-...
Page 519: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 517 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condi- Wheels Rear- All-Wheel Drive Models All-Wheel Drive Models With tion OFF the Wheel With Single-Speed Transfer Two-Speed Transfer Case Ground Drive Case Models •...
Page 520: Recreational Towing - Rear-Wheel Drive Models
518 STARTING AND OPERATING Recreational Towing — Rear-Wheel Drive Models 6. Install a suitable clamping device, designed for tow- ing, to secure the front wheels in the straight position. DO NOT flat tow this vehicle. Damage to the drivetrain will result. CAUTION! Recreational towing (for two-wheel drive models) is Towing with the rear wheels on the ground will...
Page 521: Recreational Towing - All-Wheel Drive Models (Two-Speed Transfer Case)
STARTING AND OPERATING 519 CAUTION! CAUTION! • DO NOT dolly tow any All-Wheel Drive (AWD) Towing this vehicle in violation of the above require- ments can cause severe transmission and/or transfer vehicle. Internal damage to the transmission or case damage. Damage from improper towing is not transfer case will occur if a dolly is used when covered under the New Vehicle Limited Warranty.
Page 522 520 STARTING AND OPERATING CAUTION! (Continued) WARNING! (Continued) • Failure to follow these procedures can cause severe position disengages both the front and rear drive- transmission and/or transfer case damage. Damage shafts from the powertrain and will allow the vehicle from improper towing is not covered under the to move, even if the transmission is in PARK.
Page 523 STARTING AND OPERATING 521 1. Bring the vehicle to a complete stop, with the engine running. 2. Press and hold the brake pedal. 3. Shift the transmission into NEUTRAL. 4. Using a ballpoint pen or similar object, press and hold the recessed transfer case NEUTRAL (N) button (lo- cated by the selector switch) for four seconds.
Page 524 522 STARTING AND OPERATING 8. Shift the transmission back into NEUTRAL. 12. Attach the vehicle to the tow vehicle using a suitable tow bar. 9. Firmly apply the parking brake. 13. Release the parking brake. 10. With the transmission and transfer case in NEU- TRAL, press and hold the ENGINE START/STOP NOTE: button until the engine turns off.
Page 525 STARTING AND OPERATING 523 • A flashing NEUTRAL (N) position indicator light indicates that shift requirements have not been met. Shifting Out Of NEUTRAL (N) Use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle.
Page 526 524 STARTING AND OPERATING 9. Shift the transmission into PARK and turn the engine NOTE: OFF. • Steps 1 through 5 are requirements that must be met 10. Release the brake pedal. before pressing the NEUTRAL (N) button, and must continue to be met until the shift has been completed.
Page 527: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Road Tire Installation ....543 HAZARD WARNING FLASHERS ...526 IF YOUR ENGINE OVERHEATS .
Page 528: Hazard Warning Flashers
526 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the switch bank just above the climate controls. potential for overheating by taking the appropriate ac- tion.
Page 529: Wheel And Tire Torque Specifications
WHAT TO DO IN EMERGENCIES 527 • You can also turn the temperature control to maximum WARNING! heat, the mode control to floor and the blower control to high. This allows the heater core to act as a You or others can be badly burned by hot engine supplement to the radiator and aids in removing heat coolant (antifreeze) or steam from your radiator.
Page 530: Torque Specifications
528 WHAT TO DO IN EMERGENCIES Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Lug Nut/ Bolt Size Bolt Socket Size 130 Ft-Lbs (176 N·m) M14 x 1.50 22 mm **Use only Chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.
Page 531: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 529 JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 532: Jack Location
530 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
Page 533: Spare Tire Stowage
WHAT TO DO IN EMERGENCIES 531 center-rear of the cargo floor area, just inside the liftgate opening. Thumb Screw Location Spare Tire Stowage Spare Tire Location The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle/lug wrench connected to the square socket extension to rotate the “spare tire drive”...
Page 534: Spare Tire Removal
532 WHAT TO DO IN EMERGENCIES CAUTION! Do not use power tools to winch the tire up or down. Impact type tools can damage the winch mechanism. Spare Tire Removal 1. Remove the jack tools from the bag. 2. Raise the rubber mat and remove the plug from storage compartment floor.
Page 535 WHAT TO DO IN EMERGENCIES 533 4. Slide the tire out from under the vehicle and rotate it 5. Spread the retaining tabs on the plastic plate and pull vertically behind the rear bumper. the metal stamping toward you to release it from the plastic plate.
Page 536 534 WHAT TO DO IN EMERGENCIES 6. Slide the metal stamping up the steel extension tube 7. Pinch the three short and two long tubes to remove the and winch cable. Rotate the metal stamping and push protective plate from the steel spare wheel. it through the hole in the plastic plate and wheel.
Page 537: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 535 Preparations For Jacking 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For 1. Park the vehicle on a firm, level surface as far from the example, if changing the right front edge of the roadway as possible.
Page 538 536 WHAT TO DO IN EMERGENCIES WARNING! (Continued) WARNING! (Continued) • Turn on the Hazard Warning flasher. • To assure that spare tires, flat or inflated, are • Block the wheel diagonally opposite the wheel to securely stowed, spares must be stowed with the be raised.
Page 539 WHAT TO DO IN EMERGENCIES 537 1. Loosen (but do not remove) the wheel lug nuts by 3. For the front axle, place the jack on the body flange turning them to the left, one turn, while the wheel is just behind the front tire as indicated by the triangular still on the ground.
Page 540 538 WHAT TO DO IN EMERGENCIES Front Jack Location Lift Point On Sill Molding 4. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill molding).
Page 541 WHAT TO DO IN EMERGENCIES 539 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7.
Page 542 540 WHAT TO DO IN EMERGENCIES 8. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks. 9. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage.
Page 543 WHAT TO DO IN EMERGENCIES 541 11. Insert the two long tubes on the plastic protective plate in the lug holes of the road wheel. Push the end of the winch’s cable, spring, steel sleeve and stamped cone shape wheel plate though the road wheel and protective plate.
Page 544 542 WHAT TO DO IN EMERGENCIES 12. Slide the road wheel on the ground using the protec- NOTE: Double check to ensure the tire is snug against the tive plate until it is directly under the winch and underbody of the vehicle. Damage to the winch cable between the rear bumper and exhaust system heat may result if the vehicle is driven with the tire loose.
Page 545: Road Tire Installation
WHAT TO DO IN EMERGENCIES 543 14. Reinstall the plastic plug into the floor of the cargo 2. Install the remaining lug nuts with the cone shaped area. Roll up and store the Jack, Tool Kit and Tire end of the nut toward the wheel. Lightly tighten the Changing Instructions.
Page 546: Cap-Less Fuel Fill Funnel
544 WHAT TO DO IN EMERGENCIES CAP-LESS FUEL FILL FUNNEL The funnel for the Cap-Less Fuel System is located with the jack and tire changing tools. If your vehicle is out of fuel and an auxiliary fuel can is needed, insert the funnel into the filler neck and proceed to fill the vehicle.
Page 547: Jump-Starting
WHAT TO DO IN EMERGENCIES 545 JUMP-STARTING CAUTION! If your vehicle has a discharged battery it can be jump- Do not use a portable battery booster pack or any started using a set of jumper cables and a battery in other booster source with a system voltage greater another vehicle or by using a portable battery booster than 12 Volts or damage to the battery, starter motor,...
Page 548 546 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
Page 549: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 547 1. Set the parking brake, shift the automatic transmission Jump-Starting Procedure into PARK and turn the ignition to LOCK. WARNING! 2. Turn off the heater, radio, and all unnecessary electri- cal accessories. Failure to follow this jump-starting procedure could result in personal injury or property damage due to 3.
Page 550 548 WHAT TO DO IN EMERGENCIES Connecting The Jumper Cables WARNING! (Continued) 1. Connect the positive (+) end of the jumper cable to the could result in personal injury. Only use the specific remote positive (+) post of the discharged vehicle. ground point, do not use any other exposed metal parts.
Page 551: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 549 3. Disconnect the positive (+) end of the jumper cable CAUTION! (Continued) from the positive (+) post of the booster battery. the vehicle’s battery will discharge sufficiently to 4. Disconnect the opposite end of the positive (+) jumper degrade battery life and/or prevent the engine from cable from the remote positive (+) post of the dis- starting.
Page 552 550 WHAT TO DO IN EMERGENCIES Use the least amount of accelerator pedal pressure that CAUTION! (Continued) will maintain the rocking motion without spinning the the risk of transmission failure during prolonged wheels or racing the engine. efforts to free a stuck vehicle. NOTE: Press the ESC Off switch (if necessary), to place the Electronic Stability Control (ESC) system in Partial WARNING!
Page 553: Manual Park Release
WHAT TO DO IN EMERGENCIES 551 MANUAL PARK RELEASE CAUTION! • When “rocking” a stuck vehicle by shifting be- WARNING! tween DRIVE and REVERSE, do not spin the Always secure your vehicle by fully applying the wheels faster than 15 mph (24 km/h), or drivetrain parking brake, before activating the Manual Park damage may result.
Page 554 552 WHAT TO DO IN EMERGENCIES 2. Open the center console and locate the Manual Park 3. Using a screwdriver or similar tool, push the metal Release cover, remove it by snapping the cover away latch in towards the tether strap. from the console hinges.
Page 555 WHAT TO DO IN EMERGENCIES 553 4. While the metal latch is in the open position, simulta- CAUTION! neously pull upwards on the tether strap until the lever clicks and latches in the released position. The Closing the armrest while the Manual Park Release is transmission is now out of PARK and the vehicle can activated may damage the Manual Park Release be moved.
Page 556 554 WHAT TO DO IN EMERGENCIES To Disengage the Manual Park Release Lever: 2. Once the tension has been released and the lever has been unlocked be sure it is stowed properly and locks 1. To disengage the Manual Park Release apply tension into position.
Page 557: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 555 TOWING A DISABLED VEHICLE may also be towed as described under “Recreational Towing” in the “Starting and Operating” section. This section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and drivetrain are operable, disabled vehicles Towing Condi- Wheels...
Page 558 556 WHAT TO DO IN EMERGENCIES Towing Condi- Wheels Rear-Wheel All-Wheel Drive Mod- All-Wheel Drive Models With tion OFF the Drive Models els With Single-Speed Two-Speed Transfer Case Ground Transfer Case Wheel Lift or Front NOT AL- NOT ALLOWED NOT ALLOWED Dolly Tow LOWED Rear...
Page 559: Rear Wheel Drive Models
WHAT TO DO IN EMERGENCIES 557 CAUTION! CAUTION! Do not use sling type equipment when towing. Towing the vehicle with the rear wheels on the When securing the vehicle to a flat bed truck, do not ground at more than 30 mph (48 km/h) or for more attach to front or rear suspension components.
Page 560: All-Wheel Drive Models
558 WHAT TO DO IN EMERGENCIES All-Wheel Drive Models CAUTION! The manufacturer recommends towing with all wheels • Front or rear wheel lifts must not be used. Internal OFF the ground. Acceptable methods are to tow the damage to the transmission or transfer case will vehicle on a flatbed or with one end of the vehicle raised occur if a front or rear wheel lift is used when and the opposite end on a towing dolly.
Page 561: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Oil Filter ..... .570 ENGINE COMPARTMENT — 3.6L ..561 ▫...
Page 562 560 MAINTAINING YOUR VEHICLE ▫ Front/Rear Axle Fluid ....592 ▫ Bi-Halogen Headlamps — If Equipped ..614 ▫ Transfer Case ......593 ▫...
Page 563: Engine Compartment - 3.6L
MAINTAINING YOUR VEHICLE 561 ENGINE COMPARTMENT — 3.6L 1 — Power Distribution Center (Fuses) 6 — Air Cleaner Filter 2 — Engine Oil Dipstick 7 — Washer Fluid Reservoir 3 — Engine Oil Fill 8 — Coolant Pressure Cap (Radiator) 4 —...
Page 564: Engine Compartment - 5.7L
562 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Remote Jump Start Terminals 6 — Washer Fluid Reservoir 2 — Engine Oil Fill 7 — Engine Oil Dipstick 3 — Air Filter Cleaner 8 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 9 —...
Page 565: Onboard Diagnostic System (Obd Ii)
MAINTAINING YOUR VEHICLE 563 ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 566: Emissions Inspection And Maintenance Programs
564 MAINTAINING YOUR VEHICLE “Understanding Your Instrument Panel” for further in- Normally, the OBD II system will be ready. The OBD II formation. Tighten the fuel filler cap properly and press system may not be ready if your vehicle was recently the SELECT button to turn off the message.
Page 567: Replacement Parts
MAINTAINING YOUR VEHICLE 565 3. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced •...
Page 568: Maintenance Procedures
566 MAINTAINING YOUR VEHICLE available which include detailed service information for MAINTENANCE PROCEDURES your vehicle. Refer to these Service Manuals before The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your vehicle.
Page 569: Engine Oil
MAINTAINING YOUR VEHICLE 567 The best time to check the engine oil level is about five CAUTION! (Continued) minutes after a fully warmed up engine is shut off. • Your vehicle has been built with improved fluids Checking the oil while the vehicle is on level ground will that protect the performance and durability of your improve the accuracy of the oil level readings.
Page 570 568 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil Identification Symbol The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “Maintenance Schedule” for further informa- This symbol means that the oil has tion.
Page 571 MAINTAINING YOUR VEHICLE 569 Engine Oil Viscosity — 3.6L Engine Engine Oil Viscosity — 5.7L Engine MOPAR® SAE 5W-20 engine oil approved to Chrysler MOPAR® SAE 5W-20 engine oil or equivalent such as Material Standard MS-6395 such as Pennzoil®, Shell Pennzoil®...
Page 572: Engine Oil Filter
570 MAINTAINING YOUR VEHICLE Lubricants that do not have both, the engine oil certifi- Engine Oil Filter cation mark and the correct SAE viscosity grade number The engine oil filter should be replaced with a new filter should not be used. at every engine oil change.
Page 573: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 571 Maintenance-Free Battery WARNING! Your vehicle is equipped with a maintenance-free battery. The air induction system (air cleaner, hoses, etc.) can You will never have to add water, nor is periodic main- provide a measure of protection in the case of engine tenance required.
Page 574 572 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep • It is essential when replacing the cables on the flame or sparks away from the battery. Do not use battery that the positive cable is attached to the a booster battery or any other booster source with positive post and the negative cable is attached to an output greater than 12 Volts.
Page 575: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 573 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner • The air conditioning system contains refrigerant should be checked and serviced by an authorized dealer under high pressure. To avoid risk of personal at the start of each warm season.
Page 576 574 MAINTAINING YOUR VEHICLE Protection Agency and is an ozone-saving product. How- WARNING! ever, the manufacturer recommends that air conditioning • Do not remove the A/C air filter while the ignition service be performed by authorized dealer or other service facilities using recovery and recycling equipment. is in the ON/RUN position or personal injury may result.
Page 577 MAINTAINING YOUR VEHICLE 575 2. There are glove compartment travel stops on both sides of the glove compartment door, partially close the glove compartment door and push inward to release the glove compartment travel stop on one side and repeat this procedure for the opposite side. 3.
Page 578 576 MAINTAINING YOUR VEHICLE 5. Remove the filter cover by disengaging the retaining tab and mid way snap that secures the filter cover to the HVAC housing. Disengage the mid way snap by pulling the door outward. Unhinge the filter cover on the right side to fully remove the cover.
Page 579 MAINTAINING YOUR VEHICLE 577 6. Remove the A/C air filter by pulling it straight out of the housing. 7. Install the A/C air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover.
Page 580: Body Lubrication
578 MAINTAINING YOUR VEHICLE 9. Push the door to the near closed position to reengage The external lock cylinders should be lubricated twice a the glove compartment travel stops. year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant, such as MOPAR® NOTE: Ensure the glove compartment door hinges and Lock Cylinder Lubricant directly into the lock cylinder.
Page 581 MAINTAINING YOUR VEHICLE 579 NOTE: Life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as neces- sary.
Page 582: Adding Washer Fluid
580 MAINTAINING YOUR VEHICLE 3. Grab the bottom of the wiper blade and rotate it 4. Install the wiper blade pivot pin into the wiper blade forward to unsnap the blade pivot pin from the wiper holder at the end of the wiper arm, and firmly press blade holder.
Page 583: Exhaust System
MAINTAINING YOUR VEHICLE 581 clean the wiper blades, this will help blade performance. Exhaust System To prevent freeze-up of your windshield washer system The best protection against carbon monoxide entry into in cold weather, select a solution or mixture that meets or the vehicle body is a properly maintained engine exhaust exceeds the temperature range of your climate.
Page 584 582 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 585 MAINTAINING YOUR VEHICLE 583 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 586: Cooling System
584 MAINTAINING YOUR VEHICLE Cooling System for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. WARNING! Check the engine cooling system hoses for brittle rubber, You or others can be badly burned by hot engine cracking, tears, cuts, and tightness of the connection at coolant (antifreeze) or steam from your radiator.
Page 587 MAINTAINING YOUR VEHICLE 585 Cooling System — Drain, Flush And Refill CAUTION! NOTE: Some vehicles require special tools to add coolant • Mixing of engine coolant (antifreeze) other than properly. Failure to fill these systems properly could lead specified Organic Additive Technology (OAT) en- to severe internal engine damage.
Page 588 586 MAINTAINING YOUR VEHICLE you use the same engine coolant (OAT coolant conform- CAUTION! (Continued) ing to MS-12106) throughout the life of your vehicle. • Do not use water alone or alcohol-based engine Please review these recommendations for using Organic coolant (antifreeze) products.
Page 589 MAINTAINING YOUR VEHICLE 587 • Mixing engine coolant (antifreeze) types is not recom- (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the mended and can result in cooling system damage. If engine cooling system. HOAT and OAT coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with Please note that it is the owner’s responsibility to main-...
Page 590 588 MAINTAINING YOUR VEHICLE engine coolant in open containers or allow it to remain in WARNING! puddles on the ground. If ingested by a child or pet, seek • Do not open hot engine cooling system. Never add emergency assistance immediately. Clean up any ground spills immediately.
Page 591 MAINTAINING YOUR VEHICLE 589 • Check the coolant freeze point in the radiator and in When additional engine coolant (antifreeze) is needed to maintain the proper level, only OAT coolant that meets the coolant expansion bottle. If engine coolant (anti- the requirements of Chrysler Material Standard MS- freeze) needs to be added, the contents of the coolant 12106 should be added to the coolant bottle.
Page 592: Brake System
590 MAINTAINING YOUR VEHICLE • Do not change the thermostat for Summer or Winter WARNING! (Continued) operation. If replacement is ever necessary, install high brake temperatures, excessive lining wear, and ONLY the correct type thermostat. Other designs may possible brake damage. You would not have your full result in unsatisfactory engine coolant (antifreeze) braking capacity in an emergency.
Page 593 MAINTAINING YOUR VEHICLE 591 With disc brakes, the fluid level can be expected to fall as WARNING! (Continued) the brake linings wear. However, an unexpected drop in • To avoid contamination from foreign matter or fluid level may be caused by a leak and a system check moisture, use only new brake fluid or fluid that has should be conducted.
Page 594: Front/Rear Axle Fluid
592 MAINTAINING YOUR VEHICLE The front axle fill and drain plugs should be tightened to WARNING! (Continued) 22 to 29 ft lbs (30 to 40 N·m). • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be CAUTION! damaged, causing partial or complete brake failure.
Page 595: Transfer Case
MAINTAINING YOUR VEHICLE 593 Adding Fluid CAUTION! Add fluid at the filler hole, until it runs out of the hole, Do not overtighten the plugs as it could damage them when the vehicle is in a level position. and cause them to leak. Drain Selection Of Lubricant First remove fill plug, then remove drain plug.
Page 596: Automatic Transmission
594 MAINTAINING YOUR VEHICLE Automatic Transmission CAUTION! (Continued) Selection Of Lubricant in transmission shift quality and/or torque converter shudder, and will require more frequent fluid and It is important to use the proper transmission fluid to filter changes. Refer to “Fluids, Lubricants, and ensure optimum transmission performance and life.
Page 597 MAINTAINING YOUR VEHICLE 595 with an improper fluid level can cause severe transmis- CAUTION! sion damage. Do not use chemical flushes in your transmission as CAUTION! the chemicals can damage your transmission compo- nents. Such damage is not covered by the New If a transmission fluid leak occurs, visit your autho- Vehicle Limited Warranty.
Page 598: Appearance Care And Protection From Corrosion
596 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion What Causes Corrosion? Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 599 MAINTAINING YOUR VEHICLE 597 • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once •...
Page 600 598 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, NOTE: If your vehicle is equipped with Dark Vapor de-icer salt, etc., be sure that such materials are well Chrome wheels DO NOT USE wheel cleaners, abrasives packaged and sealed.
Page 601 MAINTAINING YOUR VEHICLE 599 Stain Repel Fabric Cleaning Procedure — If Interior Care Equipped Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. •...
Page 602 600 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and WARNING! reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- Do not use volatile solvents for cleaning purposes. lowed by rinsing.
Page 603 MAINTAINING YOUR VEHICLE 601 When cleaning the rear view mirror, spray cleaner on the Seat Belt Maintenance towel or rag that you are using. Do not spray cleaner Do not bleach, dye, or clean the belts with chemical directly on the mirror. solvents or abrasive cleaners.
Page 604: Fuses
602 MAINTAINING YOUR VEHICLE FUSES WARNING! WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system • When replacing a blown fuse, always use an ap- periodically, checking for cuts, frays, or loose parts. propriate replacement fuse with the same amp Damaged parts must be replaced immediately.
Page 605: Power Distribution Center
MAINTAINING YOUR VEHICLE 603 WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Power Distribution Center The Power Distribution Center is located in the engine compartment near the battery.
Page 606 604 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Micro Fuse Description 60 Amp Yellow Rad Fan 40 Amp Green Compressor for Air Suspension - If Equipped 40 Amp Green Antilock Brakes/Electronic Stability Con- trol Pump 40 Amp Green Starter Solenoid 40 Amp Green Emission Sensors (Diesel engine only) 40 Amp Green Diesel Fuel Heater (Diesel engine only)
Page 607 MAINTAINING YOUR VEHICLE 605 Cavity Cartridge Fuse Micro Fuse Description 20 Amp Blue Engine Control Module 30 Amp Pink Body Controller #1 30 Amp Pink Driver Door Module 30 Amp Pink Front Wipers 30 Amp Pink Antilock Brakes/Stability Control Module/Valves 20 Amp Blue Trailer Tow Backup Lights - If Equipped 20 Amp Blue...
Page 608 606 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink Power Liftgate - If Equipped 10 Amp Red Daytime Running Lights 20 Amp Yellow Horn 10 Amp Red Diagnostic Port 10 Amp Red Tire Pressure Monitor - If Equipped 10 Amp Red Integrated Central Stack / Climate Control 20 Amp Yellow...
Page 609 MAINTAINING YOUR VEHICLE 607 Cavity Cartridge Fuse Micro Fuse Description 10 Amp Red Purging Pump (Diesel engine only) 15 Amp Blue Transmission Control Module 10 Amp Red Air Conditioning Clutch 20 Amp Yellow Ignition Coils (Gas), Urea Heater (Diesel) 25 Amp Natural Fuel Injectors / Powertrain 10 Amp Red Sunroof / Passenger Window Switches /...
Page 610 608 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Micro Fuse Description 10 Amp Red Antilock Brakes/Electronic Stability Con- trol 10 Amp Red Drivetrain Control Module/Front Axle Disconnect Module 10 Amp Red Engine Control Module / Electric Power Steering - If Equipped 10 Amp Red Universal Garage Door Opener / Compass / Anti-Intrusion Module...
Page 611 MAINTAINING YOUR VEHICLE 609 Cavity Cartridge Fuse Micro Fuse Description 10 Amp Red Air Suspension – If Equipped/ Trailer Tow / Steering Column Control Module 15 Amp Blue Instrument Panel Cluster F90/F91 20 Amp Yellow Power Outlet (Rear seats) Selectable 10 Amp Red Rear Console Lamp - If Equipped 20 Amp Yellow...
Page 612 610 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Micro Fuse Description F100 10 Amp Red Active Damping - If Equipped F101 15 Amp Blue Electrochromatic Mirror/Smart High Beams - If Equipped F103 10 Amp Red Cabin Heater (Diesel engine only) F104 20 Amp Yellow Power Outlets (Instrument Panel/Center Console)
Page 613: Vehicle Storage
MAINTAINING YOUR VEHICLE 611 VEHICLE STORAGE CAUTION! If you are leaving your vehicle dormant for more than 21 • When installing the power distribution center days you may want to take steps to protect your battery. cover, it is important to ensure the cover is properly You may: positioned and fully latched.
Page 614: Replacement Bulbs
612 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS Interior Bulbs Bulb Number Glove Box Lamp Grab Handle Lamp L002825W5W Overhead Console Reading Lamps VT4976 Visor Vanity Lamp V26377 Rear Cargo Lamp 214–2 Underpanel Courtesy Lamps Instrument Cluster (General Illumination) Telltale/Hazard Lamp Exterior Bulbs Bulb Number Low Beam/High Beam (Bi-Xenon) Headlamps D3S (Service at Authorized Dealer)
Page 615 MAINTAINING YOUR VEHICLE 613 Bulb Number Low Beam/High Beam (Bi-Halogen) Headlamps (Uplevel) HIR2 Front Park/Turn Signal Lamps (Base) 3157NAK Front Turn Signal Lamps (Uplevel & Premium) 3157NAK Front Park Lamp/Daytime Running Lamp (Uplevel & Premium) LED (Serviced at Authorized Dealer) Front Side Marker Lamps LED (Serviced at Authorized Dealer) Front Fog Lamps...
Page 616: Bulb Replacement
614 MAINTAINING YOUR VEHICLE BULB REPLACEMENT WARNING! NOTE: Lens fogging can occur under certain atmo- A transient high voltage occurs at the bulb sockets of spheric conditions. This will usually clear as atmospheric High Intensity Discharge (HID) headlamps when the conditions change to allow the condensation to change headlamp switch is turned ON.
Page 617: Front Turn Signal
MAINTAINING YOUR VEHICLE 615 2. Turn the access cap located on the wheel liner coun- 9. Install the access cap in the wheel liner and rotate terclockwise to remove from liner. clockwise to lock it in place. 3. Locate the headlamp bulb access cap through the CAUTION! opening in the wheel liner.
Page 618: Front Fog Lamps
616 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! • Do not touch the new bulb with your fingers. Oil Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the contamination will severely shorten bulb life. If bulb comes in contact with any oily surface, clean the the bulb comes in contact with any oily surface, bulb with rubbing alcohol.
Page 619: Rear Tail, Stop And Turn Signal Lamps
MAINTAINING YOUR VEHICLE 617 Rear Tail, Stop And Turn Signal Lamps Center High-Mounted Stop Lamp (CHMSL) The rear tail, stop, and turn signal lamps are LED. See The center high-mounted stop lamp is an LED assembly. your authorized dealer for replacement. See your authorized dealer for replacement.
Page 620: Fluid Capacities
618 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Metric Fuel (Approximate) 3.6L and 5.7L Engines 25 Gallons 94 Liters Engine Oil With Filter 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters 5.7L Engine (SAE 5W-20, API Certified) 7 Quarts 6.6 Liters Cooling System * 3.6L Engine (MOPAR®...
Page 621: Fluids, Lubricants And Genuine Parts
MAINTAINING YOUR VEHICLE 619 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Ma- terial Standard MS-12106. Engine Oil –...
Page 622 620 MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Engine Oil Filter We recommend you use a MOPAR® Engine Oil Filter. Spark Plugs – 3.6L Engine We recommend you use MOPAR® Spark Plugs (Gap 0.043 in [1.1 mm]) Spark Plugs – 5.7L Engine We recommend you use MOPAR®...
Page 623: Chassis
MAINTAINING YOUR VEHICLE 621 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar® ZF 8&9 Speed ATF™ Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer Case –...
Page 625: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart.....626 MAINTENANCE SCHEDULE ... . .624...
Page 626 624 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)/Oil Change Required” in indicator system. The oil change indicator system will “Understanding Your Instrument Panel”...
Page 627 MAINTENANCE SCHEDULES 625 • Check the tire inflation pressures and look for unusual At Every Oil Change Interval As Indicated By Oil wear or damage Change Indicator System: • Check the fluid levels of the coolant reservoir, brake • Inspect battery and clean and tighten terminals as master cylinder, and power steering and fill as needed required.
Page 628 626 MAINTENANCE SCHEDULES Maintenance Chart Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle fluid, change if using your ve- hicle for police, taxi, fleet, off- road or frequent trailer towing.
Page 629 MAINTENANCE SCHEDULES 627 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Adjust parking brake. Inspect transfer case fluid. Additional Maintenance Replace engine air filter. Replace air conditioning filter. Replace spark plugs (3.6L en- gine).** Replace spark plugs (5.7L en- gine).**...
Page 630 628 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change transfer case fluid. Inspect and replace PCV valve if necessary.
Page 631 MAINTENANCE SCHEDULES 629 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 633: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... . .633 Impaired (TDD/TTY).
Page 634 632 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .639 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....639 ▫...
Page 635: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 633 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 636: Chrysler Group Llc Customer Center
634 IF YOU NEED CONSUMER ASSISTANCE • Authorized dealer name facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer service manager first.
Page 637: In Mexico Contact
IF YOU NEED CONSUMER ASSISTANCE 635 In Mexico Contact: Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered Av. Prolongacion Paseo de la Reforma, 1240 by Bell Canada. For TTY teletypewriter users, dial 711 Sante Fe C.P.
Page 638: Warranty Information
636 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service WARNING! contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the Engine exhaust, some of its constituents, and certain manufacturer’s service contract.
Page 639: Mopar® Parts
IF YOU NEED CONSUMER ASSISTANCE 637 MOPAR® PARTS campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety operating at its best.
Page 640: Publication Order Forms
638 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS Diagnostic Procedure Manuals To order the following manuals, you may use either the Diagnostic Procedure Manuals are filled with diagrams, website or the phone numbers listed below. Visa, Mas- charts and detailed illustrations. These practical manuals tercard, American Express, and Discover orders are ac- make it easy for students and technicians to find and fix cepted.
Page 641 IF YOU NEED CONSUMER ASSISTANCE 639 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled • 1–800–387–1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 642 640 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A repre- WARNING! sent higher levels of performance on the laboratory test wheel, than the minimum required by law. The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not WARNING! include acceleration, cornering, hydroplaning, or...
Page 643 INDEX...
Page 644 642 INDEX Adaptive Cruise Control (ACC) (Cruise Control) . . .198 Alarm Adding Engine Coolant (Antifreeze) ... .586 Arm The System ......20 Adding Fuel .
Page 645 INDEX 643 Fluid and Filter Changes ....595 Brake System ......590 Fluid Change .
Page 646 644 INDEX Cargo Area Features ..... . .272 Install A LATCH-compatible Child Restraint ..102 Cargo Compartment ..... . .272 Installing Child Restraints Using The Vehicle Seat Light .
Page 647 INDEX 645 Disposal of Used Coolant ....588 Power Steering ......438 Drain, Flush, and Refill .
Page 648 646 INDEX Electronic Brake Control System ....442 Hazard Warning Flasher ....526 Brake Assist System .
Page 649 INDEX 647 Overheating ......526 Hazard Warning ......526 Starting .
Page 650 648 INDEX Fog Light Service ......616 Fuel, Flexible ......492 Folding Rear Seat .
Page 651 INDEX 649 GVWR ....... . .499 Hood Release ......173 Hazard Warning Flasher .
Page 652 650 INDEX Jack Location ......530 Keyless Entry System ..... . .23 Jack Operation .
Page 653 INDEX 651 Brake Assist Warning ....452 Rear Tail ......617 Brake Warning .
Page 654 652 INDEX Lug Nuts .......527 Modifications/Alterations, Vehicle ....9 Monitor, Tire Pressure System .
Page 655 INDEX 653 Filter Disposal ......570 Passing Light ......185 Identification Logo .
Page 656 654 INDEX Pretensioners Rear Wiper/Washer......276 Seat Belts ......63 Reclining Front Seats .
Page 657 INDEX 655 Remote Starting Safety Checks Inside Vehicle....116 EVIC Remote Start Abort Message ... .30 Safety Checks Outside Vehicle .
Page 658 656 INDEX Untwisting Procedure .....59 Service Contract ......635 Seats .
Page 659 INDEX 657 Remote .......28 System, Remote Starting .....28 Starting and Operating .
Page 660 658 INDEX Jacking .......529 Disabled Vehicle ......555 Life of Tires .
Page 661 INDEX 659 Automatic ......415 Uniform Tire Quality Grades ....639 Maintenance .
Page 662 660 INDEX Wheel and Wheel Trim Care ....598 Windshield Washers ..... . .185 Wind Buffeting.
Page 663 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehi- The antenna cable should be as short as practical and routed cle’s electronic system to provide immunity to radio frequency away from the vehicle wiring when possible. Use only fully signals.
Page 664 Chrysler Group LLC Chrysler Group LLC Chrysler Group LLC Fourth Edition Rev. 1 Printed in U.S.A. 14WD01-126-AE 14PFD41-126-AA 14PFD41-126-AA 14PFD41-126-AA First Edition First Edition First Edition Printed in U.S.A. Printed in U.S.A. Printed in U.S.A.

This manual is also suitable for:

Durango 2014

Dodge 2014 urango Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge 2014 urango

Summary of Contents for Dodge 2014 urango