Security > 802.1X Settings - Linksys SLM2005 User Manual

Chapter 
Enable Tx Force Untag When this option is enabled,
all egress frames from this port become untagged. The
default value is Dsable. When this function is disabled,
only frames with the VLAN ID equal to the PVID will become
untagged, otherwise, frames are sent with a VLAN tag.
Enable Ingress Flter
Determines how to process frames
tagged for VLANs for which the ingress port is not a
member. The default value is enabled. Ingress filtering
only affects tagged frames. If ingress filtering is disabled
and a port receives frames with a VLAN tag that uses a
different PVID than the receiving port, the packet types
will be forwarded to the port belonging to the appropriate
VLAN (determined by the VLAN tag). If ingress filtering is
enabled and a port receives frames tagged for VLANs for
which it is not a member, these frames will be discarded.
Acceptable Frame Type Sets the interface to accept all
frame types, including tagged or untagged frames, or
only tagged frames. When set to receive all frame types,
any received frames that are untagged are forwarded to
the VLAN based on the PVID of its ingress port. All frame
types are selected by default.
PVID (Port VLAN dentfer)
untagged frames received on the interface. The default
value is 1. For all other VLANs, an interface must first be
configured as an untagged member before you can assign
its PVID to that group.
Fill in the required settings for each interface, then click
Save Settngs.
Security > 802.1X Settings
Network switches can provide open and easy access
to network resources by simply attaching a client PC.
Although this automatic configuration and access is a
desirable feature, it also allows unauthorized personnel
to easily intrude and possibly gain access to sensitive
network data.
Security > 802.1X Settings
5-Port and 8-Port 10/100/1000 Ggabt Smart Swtches wth PD and AC Power
VLAN ID assigned to
Advanced Configuration
The IEEE 802.1X (dot1X) standard defines a port-based
access control procedure that prevents unauthorized
access to a network by requiring users to first submit
credentials for authentication. Access to all switch ports in
a network can be centrally controlled from a server, which
means that authorized users can use the same credentials
for authentication from any point within the network.
This Switch uses the Extensible Authentication Protocol
over LANs (EAPOL) to exchange authentication protocol
messages with the client, and a remote RADIUS
authentication server to verify user identity and access
rights. When a client connects to a switch port, the Switch
responds with an EAPOL identity request. The client
provides its identity (such as a user name) in an EAPOL
response to the Switch, which it forwards to the RADIUS
server. The RADIUS server verifies the client identity and
sends an access challenge back to the client. The EAP packet
from the RADIUS server contains not only the challenge,
but the authentication method to be used. The client can
reject the authentication method and request another,
depending on the configuration of the client software
and the RADIUS server. The authentication method must
be MD5. The client responds to the appropriate method
with its credentials, such as a password or certificate.
The RADIUS server verifies the client credentials and
responds with an accept or reject packet. If authentication
is successful, the Switch allows the client to access the
network. Otherwise, network access is denied and the
port remains blocked.
The operation of 802.1X on the Switch requires the
following:
• The Switch must have an IP address assigned.
• RADIUS authentication must be enabled on the Switch
and the IP address of the RADIUS server specified.
802.1X must be enabled globally for the Switch.
•
Each Switch port that will be used must be set to dot1X
•
"Auto" mode.
• Each client that needs to be authenticated must
have dot1X client software installed and properly
configured.
The RADIUS server and 802.1X client support EAP. (The
•
Switch only supports EAPOL in order to pass the EAP
packets from the server to the client.)
The RADIUS server and client also have to support the
•
same EAP authentication type – MD5. (Some clients
have native support in Windows, otherwise the dot1x
client must support it.)
80.1X Mode Enables or disables 802.1X mode.
RADIUS IP Enter the IP address of the server.
8