Related Manuals for Sunfire XTEQ8
Summary of Contents for Sunfire XTEQ8
- Page 1 Subwoofer XTEQ 8 XTEQ 10 XTEQ 12 User's Manual 9901375_Rev-A_Sunfire_XTEQ_User_Manual_0812_PRINT_ENG.indd 1 8/12/14 7:10 PM...
-
Page 2: Safety Instructions
Le symbole de l’éclair fléché dans un triangle équilatéral, est destiné à alerter l’utilisateur de la présence d’une “tension dangereuse” dans le boîtier du produit qui peuvent être des ampleur suffisante pour constituer un risque d’électrocution aux personnes. Ce symbole est destiné à alerter l'utilisateur de la présence d'opération et de maintenance (entretien) dans la documentation accompagnant l'appareil. -
Page 3: Table Of Contents
System Configurations....14 Unpacking and Care.......4 Specifications......18 Control Panel Features....6 Troubleshooting Guide....20 Installation......8 Limited Warranty......22 Connections......9 Service Assistance.......23 Location........10 To find out more about this and other Sunfire products, please visit our website: www.sunfire.com User's Manual 9901375_Rev-A_Sunfire_XTEQ_User_Manual_0812_PRINT_ENG.indd 3 8/12/14 7:10 PM... -
Page 4: Introduction
Introduction Care To maintain the speaker cabinet’s fi nish, fi rst Thank you for purchasing this Sunfi re XTEQ unplug the power cord and then use a soft Subwoofer. The big breakthrough features cloth to clean the surfaces. If your Sunfi re of the subwoofer are its innovate tracking Subwoofer needs servicing, please read the down converter amplifi er, its long throw,... -
Page 5: Crossover Frequency
Control Panel Features 1. Crossover Frequency 3. Phase Control This control changes the high frequency This control changes the relative phase cutoff point. With the control set to 100 Hz, of the subwoofer with respect to the other the subwoofer will reproduce frequencies speakers. -
Page 6: Control Panel Features
Control Panel Features Continued 6. Line Level Outputs 8. Output Switch Line level output signals are available This switch affects the frequency range of at these jacks. These outputs are active the line level outputs. whenever a signal is hooked up to the In the bypass position, the outputs are a full inputs of the subwoofer. -
Page 7: Power Switch
The second subwoofer will not require any ONLY MAKE THIS ADJUSTMENT IF THE connections to its line level inputs, as it SUbWOOFER WILL bE CONNECTED receives the audio through its slave input. TO A VOLTAGE SUPPLY OF bETWEEN 220~240VAC @50Hz. 10. -
Page 8: Installation
Installation AC Power Considerations Observe the following general precautions and read the safety instructions on pages two and three before using your Sunfire • Ensure that the unit is plugged into an subwoofer. outlet capable of supplying the correct voltage and amperage specified for •... -
Page 9: Connections
Connections Please consider the following • Whenever possible, keep the power when setting up your new system: cords away from the signal cables or speaker wires to prevent any hum • before making or changing any or interference being heard in connections, always make sure that the the speakers. -
Page 10: Location
The following are additional • Shut things down and install the recommendations that Sunfire has found to subwoofer in this position. Make be beneficial in finding the prime location for sure the control panel is not touching your subwoofer: anything, and that it can receive good ventilation. -
Page 11: User's Manual
Room Equalization Procedure to maximize your subwoofer(s) full potential. The Sunfire XTEQ unitizes the most current and advanced auto equalization system available. As you found in the last exercise, 'Location',... -
Page 12: Room Equalization Procedure
Only use the microphone supplied by out of standby mode. Sunfire for this process. • To do so, press the start button again. 4. Plug the microphone into the subwoofer’s microphone jack (MIC... - Page 13 I use? • Leave the Auto EQ switch in the Sunfire recommends that you use BOTH – “EQ on” position to use the settings the Sunfire Auto Room Equalization AND that you just configured. If at any time your AV receiver’s Auto Calibration System.
-
Page 14: System Configurations
System Configurations The following pages show some typical connections that you might make in your installation. They show how the inputs and outputs of the Sunfire Subwoofer are connected to your preamplifier or AV receiver. Connections to a Preamplifier’s Subwoofer Output If your AV Receiver / Preamplifier has a subwoofer output (often labeled LFE for Low Frequency Effects), it can be connected to the subwoofer’s left or right input as shown. - Page 15 Connections to a Preamplifier Using "Y" Cables If your preamplifier does not have a dedicated sub/LFE output, you can use “Y” cables to send its main outputs to both the subwoofer and your amplifier. The subwoofer will play the low frequency range and your front speakers will play the full range.
- Page 16 Using the Line-Level Outputs If you are using a preamplifier that does not have a sub/LFE output, you can send its left and right front output into the subwoofer’s line-level inputs and then connect the subwoofer’s line-level outputs to the inputs of your amplifier. The subwoofer will play the low frequencies and your amplifier and front speakers will play the frequency range of the subwoofer's outputs.
- Page 17 Using the Slave Input and Output The SLAVE output from one XTEQ subwoofer can be connected to the SLAVE input of a second XTEQ subwoofer. The second subwoofer will then receive the optimum audio signals from the first. There is no need to adjust the controls of the second subwoofer, as the audio is controlled by the controls and EQ setting of the first.
-
Page 18: Specifications
Specifications MODEL XTEQ8 XTEQ10 XTEQ12 Driver Complement 8” Active Side 10” Active Side 12” Active Side Firing Driver Firing Driver Firing Driver 8” Side Firing 10” Side Firing 12” Side Firing Passive Radiator Passive Radiator Passive Radiator Amplifier Power 1,800 Watt... - Page 19 User's Manual 9901375_Rev-A_Sunfire_XTEQ_User_Manual_0812_PRINT_ENG.indd 19 8/12/14 7:10 PM...
-
Page 20: Troubleshooting Guide
Troubleshooting The Sunfire Subwoofer is expertly designed • If the preamplifier’s subwoofer/LFE and built to provide years of trouble-free output has an adjustable crossover performance. Most problems that occur can frequency, make sure that the Sunfire usually be solved by checking your setup or subwoofer’s own crossover point is set... - Page 21 where they first enter the room, so Adding any component such as a subwoofer they are making no connection to to an existing system will often give rise to your preamplifier, TV, or any other a hum which wasn’t there before. Your first component.
-
Page 22: Limited Warranty
SUNFIRE XTEQ will be free improper installation, commercial use, of manufacturing defects in material and abuse, negligence, or normal wear and... -
Page 23: Service Assistance
Internet through unauthorized Internet SUNFIRE products are sold exclusively dealers are not covered by the SUNFIRE / through authorized dealers. This warranty is Core brands warranty and may be either: VOID if the products have been purchased from an unauthorized dealer. - Page 24 1800 South McDowell blvd, Petaluma, CA 94954 1-800-472-5555 • 1-707-778-5733 www.Sunfi re.com ©2014 Core Brands, LLC. All rights reserved. Sunfi re is a registered trademark of ® Corebrands, LLC, a Nortek company. All other trademarks are the property of their respective owners.