Advertisement
STEP 9
Walk test. Walk test the unit by walking across the
detection pattern from both sides. The red LED should light as you
cross each detection pattern "finger". (Alarm transmissions will
occur in walk test.)
WALK ACROSS
DETECTION PATTERN
WATCH RED LED AS
DETECTOR SENSES
MOTION
STEP 13
System test. Place the receiver into a sensor test
mode. Stay out of the detection pattern of the PIR for at least
4 minutes then walk across the detection pattern. The receiver
should indicate that the signal was received.
WAIT AT LEAST 4 MINUTES BEFORE
WALKING ACROSS THE DETECTION PATTERN!
1
2
3
4
5
6
7
8
9
0
#
*
SYSTEM IN TEST MODE
SHOULD BEEP AS ALARM
SIGNAL IS RECEIVED
AFTER WAITING, WALK
ACROSS DETECTION
PATTERN
Optional Vertical Curtain Lens
See the figure for
details on changing lenses.
PRY TABS UP TO
REMOVE LENS
BRACKET
INSERT NEW LENS
WITH SMOOTH SIDE
OUT
VERTICAL
CURTAIN LENS
SIDE
VIEW
80'
(24.38 m)
TOP VIEW
4.4'
(1.34 m)
40'
(12.19 m)
STEP 10
Adjust detection pattern. If the detection
pattern is too high or low, loosen the adjustment post and slide
the circuit board up or down.
LOOSEN
ADJUSTMENT
POST TO SLIDE
BOARD
SLIDE BOARD
UP OR DOWN
TO ADJUST
PATTERN
NOTE: BOARD UP
ADJUSTS
PATTERN DOWN
Optional Swivel Mount
An optional swivel mount is
supplied for mounting the TMD-90 to a wall in special situations.
Refer to the figure for details on attaching the swivel mount to the
case (swivel mount must be assembled first).
LONG
SCREW (1)
SWIVEL
BALL
SHORT
SCREWS (4)
BASE
PUNCH OUT
KNOCKOUTS
SWIVEL
BASE
Optional Lens Masks
Adhesive stick-on labels are
provided to mask unwanted detection areas of each lens. Apply
the labels to the inside of the lens.
APPLY LENS MASKING
STICKERS TO THE INSIDE
OF THE LENS
STEP 11
Program transmitter into receiver. Refer to the
instructions supplied with the supervised receiver to program the
TMD-90 as a non-restoring PIR sensor. Turn the walk test switch
(#6) OFF. Press the TEST button to cause the unit to send a
signal. The TEST button will not send a valid signal if the unit
is in walk test (switch #6 ON).
RECEIVER
PRESS TEST
LEARNS
BUTTON
TRANSMITTER
TO SEND
ID CODE
SIGNAL
SWITCH #6
MUST BE
OFF
Optional Long Range Lens
See the figure for
changing supplied lenses. Do not set the pulse count for more
than 2 pulses when using the long range lens.
PRY TABS UP TO
REMOVE LENS
BRACKET
INSERT NEW LENS
WITH SMOOTH SIDE
OUT
LONG RANGE LENS
TOP VIEW
SIDE VIEW
6.56'
13.12'
26.24'
52.48'
(2 m)
(4 m)
(8 m)
(16 m)
SPECIFICATIONS
DETECTOR: Balanced dual-element pyro electric
LENS: Aspheric fresnel lens with 24 facets,
9 main, 8 intermediate, 5 short, 2 creep
DETECTION PATTERN: 40 x 40 feet (12.2 x 12.2 M)
VERTICAL ADJUST: Installer adjustable up and down
SIGNAL PROCESSING: Selectable pulse count (2, 3 & 5 pulses)
Pulse window (8, 16 & 32 seconds)
POWER REQUIREMENTS: Four type "AA" MN1500 batteries
Operating:12 mA maximum
Standby: 15 uA maximum
LED: Extra bright for walk test
RF ENCODING: Linear SX format (A1D PPM @ 200 bps)
NUMBER OF CODES: 16,777,216
TAMPER SWITCH: Switch linked to case cover
SHIELDING: Metal shielding for maximum RFI/EMI immunity
OPERATING TEMPERATURE:
+32° to +122° F
(0° to +50° C)
DIMENSIONS: 5.75" high x 3.25" wide x 1.75" deep
COLOR: Cool Gray 1C
MOUNTING: Wall, corner or swivel
STEP 12
Replace and lock cover. Replace the unit's
cover and secure it with the locking screw.
LOCKING TAB
WILL SNAP SHUT
Optional Horizontal Curtain Lens
changing supplied lenses.
HORIZONTAL
14.43'
CURTAIN LENS
(4.4 m)
80'
(24.38 m)
10.5'
(3.2 m)
131.2'
(40 m)
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The
Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers
who buy direct from Linear or through Linear's normal distribution channels. Linear does not warrant
this product to consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer's warranty, if any. There are no obligations or liabilities on the part of Linear LLC for
consequential damages arising out of or in connection with use or performance of this product
or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and
implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This
Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.
1
For U.S. installations only: The radios are required to comply with FCC Rules
and Regulations as Part 15 devices. As such, they have limited transmitter
power and therefore limited range.
1
A receiver cannot respond to more than one transmitted signal at a time and
may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
1
Changes or modifications to the device may void FCC compliance.
1
Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
1
A general knowledge of radio and its vagaries should be gained prior to acting
as a wholesale distributor or dealer, and these facts should be communicated
to the ultimate users.
Copyright © 2006 Linear LLC
CLOSE
CASE
INSERT LOCKING
SCREW
See the figure for
PRY TABS UP TO
REMOVE LENS
BRACKET
INSERT NEW LENS
WITH SMOOTH SIDE
OUT
TOP
VIEW
3'
40'
(.91 m)
(12.19 m)
SIDE VIEW
208457 E
Advertisement
