Table of Contents
Advertisement
A-5
K466-4 Installation (For Hobart feeders; i.e. 27...)
1. Remove brass cable connector (see Figure A.2)
from the K466-4 kit and screw it on to the feeder
end of the gun cable. Tighten the connector
with the wrench provided.
2. Attach the phone plug connector of the gun con-
trol cable provided to the trigger connector on
the front of the Hobart feeder.
K466-5 Installation (For L-Tec feeders equipped
with an L-Tec feeder connector assembly, MIG
35, MIG 31A, 225...)
1. Remove brass cable connector (see Figure A.2)
from the K466-5 kit and screw it onto the feeder
end of the gun cable. Tighten the connection
with the wrench provided.
2. For L-Tec machines that require trigger lead
connections to be made at a terminal strip locat-
ed within the machine (L-Tec 225), a gun con-
trol cable with forked terminals is provided.
Connect the terminated leads to the terminal
strip. For a machine that requires a twist-lock
gun control cable connection, continue to use
the L-Tec gun control cable provided with the L-
Tec wire feeder connector assembly. Connect
the twist-lock plug to the proper receptacle on
the machine.
I N S U L A T O R
B R A S S C A B L E
L I N E R A S S E M B L Y ( L I N E R B U S H I N G T O B E S E A T E D
T I G H T A G A I N S T B R A S S C A B L E C O N N E C T O R
C O N N E C T O R
I N S U L A T I O N T U B E
P L U G
M O L D E D G A S
C A B L E H A N D L E
G U N H A N D L E
C A B L E
F E E D E R E N D
T I P H O L D E R
( K 4 6 6 - 1 O N L Y )
S E T S C R E W
S H I E L D C L A M P I N G S C R E W S
G U N T U B E
T I P
INSULATION TUBE
(K466-1 ONLY)
BRASS CABLE
CONNECTOR
SET SCREW
LINER ASSEMBLY (LINER BUSHING TO BE SEATED
TIGHT AGAINST BRASS CABLE CONNECTOR
INSTALLATION
FIGURE A.2
FEEDER END
CABLE HANDLE
MOLDED GAS
CABLE
PLUG
K126-10, K126-11 AND K126-12 INNERSHIELD® PRO
K466-6, K466-7, and K466-9 Installation
(Wirematic, Hobart Series 2000 Feeders, SP100T
Type and Power MIG)
1. Remove brass cable connector (see Figure A.2)
from the connector kit and screw it onto the feeder
end of the gun cable. Tighten the connection with
the wrench provided.
2. Attach the gun control cable provided to the trigger
connector on the wire feeder.
K613-2, K613-7 Installation (Tweco #5 compatible
feeders)
1. Remove brass cable connector from the kit and
screw it onto the feeder end of the gun cable.
Tighten the connection with the wrench provid-
ed.
2. For K613-7, attach the round connector of the
gun control cable provided to the trigger con-
nector on the front of the Lincoln feeder.
K613-6 Installation (Lincoln Feeders, 3/32" diam-
eter wire)
1. Remove brass cable connector and insulation
tube from the kit. Slide the insulation tube onto
the connector from the threaded end and screw
it onto the feeder end of the gun cable. Tighten
the connection with the wrench provided.
GUN HANDLE
SHIELD CLAMPING SCREWS
TIP HOLDER
INSULATOR
A-5
GUN TUBE
TIP
Advertisement
Table of Contents
