Acer Lenovo 3000 J Series User Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Desktop
  5. Lenovo 3000 J Series
  6. User manual
Acer Lenovo 3000 J Series User Manual

Acer Lenovo 3000 J Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Guide
Lenovo 3000 J Series
Types 7387, 7388, 7389, 7393, 7394, 7395

Advertisement

Table of Contents
loading

Related Manuals for Acer Lenovo 3000 J Series

Summary of Contents for Acer Lenovo 3000 J Series

  • Page 1 User Guide Lenovo 3000 J Series Types 7387, 7388, 7389, 7393, 7394, 7395...
  • Page 3 Lenovo 3000 J Series...
  • Page 4 Note Before using this information and the product it supports, be sure to read the “Important safety information” on page v and Appendix B, “Notices,” on page 71. Second Edition (August 2006) © Copyright Lenovo 2005, 2006. Portions © Copyright International Business Machines Corporation 2005. All rights reserved.

  • Page 5: Table Of Contents

    Contents Important safety information ..v Installing security features . . 34 Padlock loop . . 35 Conditions that require immediate action . Password protection . 35 General safety guidelines . . vi Changing the battery . .
  • Page 6 www.lenovo.com . 60 Extended AT commands . . 65 Help and service . 61 MNP/V.42/V.42bis/V.44 commands . . 66 Using the documentation and diagnostic Fax Class 1 commands . 67 programs . . 61 Fax Class 2 commands . 67 Calling for service .

  • Page 7: Important Safety Information

    Important safety information Note Please read the following important safety information first. This information can help you safely use your desktop or notebook personal computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement ™...

  • Page 8: General Safety Guidelines

    In the unlikely event that you notice any of the following conditions, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance.

  • Page 9: Power Cords And Power Adapters

    Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer.

  • Page 10: Extension Cords And Related Devices

    Extension cords and related devices Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating.

  • Page 11: Heat And Product Ventilation

    shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state. Heat and product ventilation Computers generate heat when turned on and when batteries are charging. Notebook computers can generate a significant amount of heat due to their compact size.

  • Page 12: Additional Safety Information

    v Remove CD and DVD discs from the computer when not in use. v Do not bend or flex CD and DVD discs, or force them into the computer or their packaging. v Check CD and DVD discs for cracks before each use. Do not use cracked or damaged discs.

  • Page 13: Modem Safety Information

    Dispose of the battery as required by local ordinances or regulations. Modem safety information Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm.

  • Page 14: Power Supply Statement

    Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.

  • Page 15: Introduction

    Introduction This User Guide contains the following information: v Chapter 1, “Arranging your workspace,” on page 1 provides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets. v Chapter 2, “Setting up your computer,” on page 3 provides information about setting up your computer and software and operating system installation.
  • Page 16 User Guide...

  • Page 17: Chapter 1. Arranging Your Workspace

    Chapter 1. Arranging your workspace To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace.

  • Page 18: Air Circulation

    Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare.

  • Page 19: Chapter 2. Setting Up Your Computer

    Chapter 2. Setting up your computer Before you begin, make sure you set up your computer in the best possible work area that suits your needs and the kind of work you do. For more information, refer to Chapter 1, “Arranging your workspace,” on page 1. Note: Read “Important safety information”...

  • Page 20: Memory Connector

    Note: Some models will have keyboards with a fingerprint reader. After you setup and turn on your computer, refer to the Access Help online help system for information about your fingerprint reader. See “Access Help” on page 60 for instructions on how to open the online help system.
  • Page 21 5. If you have a modem, connect the modem using the following information. L IN L I N L I N L IN This illustration shows the two connections on the back of the computer that are needed to set up your modem. In the United States and other countries or regions that use the RJ-11 telephone outlet, attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer.
  • Page 22 7. If you have powered speakers with an ac adapter, use the following instructions. a. Connect the cable that runs between the speakers, if necessary. On some speakers, this cable is permanently attached. b. Connect the ac adapter cable to the speaker. c.
  • Page 23 1 USB Use this connector to attach a device that requires a USB connection, such as a keyboard, mouse, scanner, printer, or personal digital assistant (PDA). 2 Serial Use this connector to attach an external modem, serial printer, or other device that uses a 9-pin serial connector. 3 S-video Use this connector to attach a television set that has an S-Video connector.

  • Page 24: Turning On Power

    Turning on power Turn on the monitor and other external devices first, and then turn on the computer. When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled software, the software installation program starts. If you experience any problems during startup, see Chapter 7, “Troubleshooting and diagnostics,”...

  • Page 25: Updating Your Operating System

    Updating your operating system Microsoft makes updates available for various operating systems through the Microsoft Windows Update Web site. The Web site automatically determines what Windows updates are available for your specific computer and lists those updates only. Updates could include security fixes, new versions of Windows components (such as media player), fixes to other portions of the Windows operating system, or enhancements.
  • Page 26 User Guide...

  • Page 27: Chapter 3. Installing Options

    Chapter 3. Installing options This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, drives, or adapters. When installing an option, use these instructions along with the instructions that come with the option.
  • Page 28 Microprocessor (varies by model type) ® ® v Intel Pentium 4 processor with HyperThreading Technology v Intel Pentium D processor ® v Intel Celeron D processor ™ v Intel Core 2 Duo processor v AMD Athlon 64 processor v AMD Sempron processor v Internal cache (size varies by model type) Memory v Support for two DDR2 DIMMs...

  • Page 29: Microprocessor Fan Connector

    Input/output features v 25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP) v 9-pin serial connector v Six 4-pin, USB connectors (two on front panel and four on rear panel) v Standard mouse connector v Standard keyboard connector v Ethernet connector v VGA monitor connector v Five audio connectors (headphone and microphone on front panel and line in, line out, and microphone on rear panel)

  • Page 30: Specifications

    Specifications This section lists the physical specifications for your computer. Dimensions Height: 392 mm (15.43 in.) Width: 180 mm (7.09 in.) Depth: 445 mm (17.52 in.) Weight Minimum configuration as shipped: 9.1 kg 20.06 lb) Maximum configuration: 10.2 kg (22.5 lb) Environment Air temperature: System on: 10°...

  • Page 31: Tools Required

    v Internal options – System memory, called dual inline memory modules (DIMMs) – Peripheral component interconnect (PCI) adapters – Internal drives, such as: - Optical drives, such as CD drives and DVD drives (some models) - Serial ATA hard disk drive Note: When adding an additional serial ATA hard disk drive, the drive must support the legacy four-pin power connector.

  • Page 32: Handling Static-Sensitive Devices

    Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instructed to do so. When you handle options and other computer components, take these precautions to avoid static electricity damage: v Limit your movement.

  • Page 33: Locating The Connectors On The Front Of Your Computer

    Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer. 1 Headphone connector 3 USB connector 2 Microphone connector 4 USB connector Chapter 3. Installing options...

  • Page 34: Locating The Connectors On The Rear Of Your Computer

    Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. 1 Power connector 9 Ethernet connector 2 Voltage switch 10 USB connectors 3 Mouse connector 11 Microphone connector 4 Keyboard connector 12 Audio line out connector 5 Serial connector...

  • Page 35: Diskette Drive Connector

    Connector Description Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Keyboard connector Used to attach a keyboard that uses a standard keyboard connector. Serial connector Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector.

  • Page 36: Obtaining Device Drivers

    Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.lenovo.com/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files. Removing the cover Important Read “Important safety information” on page v and “Handling static-sensitive devices”...

  • Page 37: Locating Components

    Locating components The following illustration will help you locate the various components in your computer. 1 Microprocessor and heat sink 5 PCI adapter connectors 2 Memory modules 6 PCI adapter 3 PCI Express x1 7 Power supply assembly adapter connector 4 PCI Express x16 graphics adapter connector Identifying parts on the system board...

  • Page 38: Battery

    The following illustration shows the locations of parts on the system board (some models). Microprocessor and heat sink Front USB connectors (2) Microprocessor fan connector Serial (COM2) connector Memory connector 1 Front audio connector Memory connector 2 PCI adapter connectors (2) Power connector PCI Express x1 graphics adapter connectors...
  • Page 39 The following illustration shows the locations of parts on the system board (some models). Microprocessor fan connector Front panel connector Microprocessor and heat sink SATA IDE connectors (2) Memory connector 1 Front USB connectors (2) Memory connector 2 Serial (COM2) connector Clear CMOS/Recovery jumper PCI adapter connectors (2) Power connector...

  • Page 40: Installing Memory

    Installing memory Your computer has two connectors for installing DIMMs that provides up to a maximum of 4.0 GB of system memory. When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin DDR2 SDRAM. v Use 256 MB, 512 MB, 1.0 GB or 2.0 GB memory modules in any combinatio up to 4.0.

  • Page 41: Installing Adapters

    Installing adapters This section provides information and instructions for installing and removing adapters. Your computer has three expansion slots for PCI adapters. One slot, used for an AGP adapter or a PCI Express x16 adapter, is available on some models. You can install an adapter up to 228 mm (9 inches) long in the AGP, PCI Express x1, or PCI Express x16 slot, PCI slot 2, or PCI slot 3.

  • Page 42: Installing Internal Drives

    5. Secure the adapter with the screw as shown. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 38. Installing internal drives This section provides information and instructions for removing and replacing internal drives.

  • Page 43: Drive Specifications

    Internal drives are installed in bays. In this book, the bays are referred to as bay 1, bay 2, and so on. When you install an internal drive, it is important to note what type and size of drive that you can install in each bay. Also, it is important to correctly connect the internal drive cables to the installed drive.
  • Page 44 The following table describes some of the drives you can install in each bay and their height requirements. 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) CD drive or DVD drive (preinstalled in some models) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3.5-inch hard disk drive (requires a Universal Adapter Bracket, 5.25 to 3.5-inch)*...

  • Page 45: Installing A Drive

    Installing a drive To install an internal drive, follow these steps: 1. Remove the cover. See “Removing the cover” on page 20. 2. Remove the two screws at the rear of the right side cover and slide the cover to the rear to remove. 3.
  • Page 46 5. Remove the front bezel by removing the two screws and releasing the six plastic tabs inside the chassis and then completely remove the bezel. Feed the power LED cable through the front chassis opening as the bezel is removed. Note: Be careful so that you do not break the power LED cable, because the cable is attached to the bezel assembly.
  • Page 47 6. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 7. Remove the plastic panel in the bezel for bay 2 by squeezing the plastic tabs that secure the panel on the inside of the bezel.
  • Page 48 9. Install the drive into the bay. Align the screw holes and install four screws to secure the drive. 10. A hard disk drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board. User Guide...
  • Page 49 The steps to connect a drive are different depending on the type of drive you are connecting. Use one of the following procedures for your drive connection. Connecting the first CD drive or DVD drive 1. Locate the three-connector signal cable that comes with your computer or with the new drive.

  • Page 50: Installing Security Features

    4. Locate one of the extra four-wire power connectors and connect it to the drive. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables”...

  • Page 51: Padlock Loop

    Padlock loop Your computer is equipped with a padlock loop that locks the cover to your computer when a padlock is installed. Using a padlock at least or at 5 mm or 3/16-inch can secure your computer cover to help prevent unauthorized people from gaining access to the inside of your computer.
  • Page 52 Refer to “Lithium battery notice” on page x for information about replacing and disposing of the battery. To change the battery: 1. Turn off the computer and all attached devices. 2. Unplug the power cord and remove the cover. See “Identifying parts on the system board”...

  • Page 53: Erasing A Lost Or Forgotten Password (Clearing Cmos)

    9. Turn on the computer and all attached devices. 10. Use the Setup Utility program to set the date and time and any passwords. See Chapter 5, “Using the Setup Utility,” on page 47. Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords.

  • Page 54: Replacing The Cover And Connecting The Cables

    Replacing the cover and connecting the cables After working with options, you need to install any removed parts, replace the cover, and reconnect any cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the Setup Utility program.

  • Page 55: Chapter 4. Recovering Software

    Chapter 4. Recovering software The Rescue and Recovery program is software aimed at helping users restore their computer data and recover from software or hardware-related failures. In the event of a computer failure, use the Rescue and Recovery program to restore the contents of the primary hard drive to a previously saved state.

  • Page 56: Backup And Recovery

    Attention: When you restore the factory contents from the Product Recovery discs, all files currently on the hard disk will be deleted and replaced by the original factory contents. During the restore process, you will be given the opportunity to save one or more files currently on your hard disk drive to other media before any data is removed.

  • Page 57: Using The Rescue And Recovery Workspace

    For information about performing a restore operation from the Rescue and Recovery workspace, see “Using the Rescue and Recovery workspace.” Using the Rescue and Recovery workspace The Rescue and Recovery workspace resides in a protected, hidden area of your hard disk that operates independently from the Windows operating system. This enables you to perform recovery operations even if the Windows operating system cannot be started.

  • Page 58: Solving Recovery Problems

    Note: After restoring your hard disk to the original factory content, you might have to reinstall some software or drivers. Refer to the following notes for more information. v For information about other features of the Rescue and Recovery workspace, click Help.

  • Page 59: Creating And Using A Recovery Repair Diskette

    2. In the Rescue Media area, select the type of rescue media you want to create. You can create rescue media using a CD, USB hard drive, or an internal hard drive. 3. Click OK. 4. Follow the instructions on the screen. To use rescue media, do one of the following: v Insert the rescue disc and restart your computer.

  • Page 60: Recovering Or Installing Device Drivers

    Recovering or installing device drivers Before you can recover or install device drivers, your operating system must be installed on your computer. Make sure that you have the documentation and software media for the device. Device drivers for factory-installed devices are located on the computer hard disk (usually drive C) in the SWTOOLS\drivers folder.
  • Page 61 8. When the Setup Confirmation window appears, press Enter. 9. The computer restarts. Note: If you are using an external device, you first must turn off your computer before connecting the external device. For more information on Setup Utility, see Chapter 5, “Using the Setup Utility,” on page 47.
  • Page 62 User Guide...

  • Page 63: Chapter 5. Using The Setup Utility

    Chapter 5. Using the Setup Utility The Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using.

  • Page 64: Password Considerations

    Password considerations A password can be any combination of up to twelve characters (a-z and 0-9) and symbols. For security reasons, it is a good idea to use a strong password that cannot be easily compromised. Strong passwords typically adhere to the following rules: v Have at least eight characters in length v Contain at least one alphabetic character, one numeric character, and one symbol...

  • Page 65: Using Security Profile By Device

    Using Security Profile by Device Security Profile by Device is used to enable or disable user access to the following devices: IDE controller When this feature is set to Disable, all devices connected to the IDE controller (such as hard disk drives or the CD-ROM drive) are disabled and will not be displayed in the system configuration.

  • Page 66: Changing The Startup Device Sequence

    Changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 47). 2. Select Startup. 3. Select Startup Sequence. See the information displayed on the right side of the screen.

  • Page 67: Chapter 6. Updating System Programs

    Chapter 6. Updating system programs This chapter contains information about updating POST/BIOS and how to recover from a POST/BIOS update failure. Using system programs System programs are the basic layer of software that is built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the Setup Utility program.
  • Page 68 User Guide...

  • Page 69: Chapter 7. Troubleshooting And Diagnostics

    Chapter 7. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see Chapter 8, “Getting information, help, and service,” on page 59 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problem.

  • Page 70: Diagnostic Programs

    Symptom Action The keyboard does not work. Verify that: The computer does not respond v The computer is turned on. to the keyboard. v The monitor is turned on and the brightness and contrast controls are set correctly. v The keyboard is securely connected to the keyboard connector on the front or rear of the computer.

  • Page 71: Pc-Doctor For Windows

    Notes: 1. You can download the latest version of the diagnostic programs from http://www.lenovo.com/support/. Type your machine type into the Use Quick Path field and click Go to find the downloadable files that are specific to your computer. 2. If you are unable to isolate and repair the problem yourself after you run PC-Doctor for Windows and PC-Doctor for DOS, save and print the log files created by both diagnostic programs.
  • Page 72 Note: You will need a diskette drive on your computer or a USB diskette drive to complete this procedure. 1. Shut down the operating system and turn off the computer. 2. If you are using a USB diskette drive, plug it into the computer. 3.

  • Page 73: Cleaning The Mouse

    5. Follow the prompts on the screen. The computer will reboot. 6. When the computer restarts, the diagnostic program opens automatically. Select the diagnostic test you want to run. Press the F1 key for additional help. Cleaning the mouse This section provides instructions on how to clean your mouse. The procedure will be different depending on whether you have an optical or non-optical mouse.
  • Page 74 Note: The following illustration might be slightly different from your mouse. 1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage To clean a mouse with a ball, follow the instructions below: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3.

  • Page 75: Chapter 8. Getting Information, Help, And Service

    Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactured by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful resources relating to your computing needs.

  • Page 76: Access Help

    – Viewing critical system information v Resource Center with support in one convenient place for tasks, such as: – One-button system recovery – Automatic updates – Performance restoration – Easy network connectivity and management v Message Center with information about system and support features including: –...

  • Page 77: Help And Service

    Help and service If you need help and service for your computer, you will find a wide variety of sources available to help you. Using the documentation and diagnostic programs Many computer problems can be solved without outside assistance. If you experience a problem with your computer, see Chapter 7, “Troubleshooting and diagnostics,”...

  • Page 78: Using Other Services

    For a list of service and support phone numbers for your country or region, go to http://www.lenovo.com/support/ and click Support phone list or refer to the warranty and safety information provided with your computer. Note: Phone numbers are subject to change without notice. If the number for your country or region is not provided, contact your Lenovo reseller or Lenovo marketing representative.

  • Page 79: Appendix A. Manual Modem Commands

    Appendix A. Manual modem commands This appendix provides commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection.
  • Page 80 Command Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected Internal speaker always on...

  • Page 81: Extended At Commands

    Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 &D_ Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle...

  • Page 82: Mnp/V.42/V.42Bis/V.44 Commands

    Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11,...

  • Page 83: Fax Class 1 Commands

    Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing Receive data +FRM=n +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class.

  • Page 84: Voice Commands

    +FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID. Voice commands Select Baud Rate #BDR #CID Enable Caller ID detection and reporting format Select Data, Fax or Voice/Audio #CLS #MDL?
  • Page 85 Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix A.
  • Page 86 User Guide...

  • Page 87: Appendix B. Notices

    Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.

  • Page 88: Television Output Notice

    vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.

  • Page 89: Index

    Index drives (continued) installing 29 Access Help 60 internal 12, 26 adapters removable media 26 installing 25 specifications 27 peripheral component interconnect (PCI) 15 slots 25 AGP connector 18 antivirus software, updating 9 environment, operating 14 arranging your workspace 1 Ethernet connector 18, 19 audio line in connector 18, 19 exiting, Setup Utility 50...
  • Page 90 mouse, cleaning serial connector 18, 19 non-optical 57 Setup Utility 47 optical mouse 57 startup sequence 44 software installing 8 recovering 39 startup sequence, rescue device 44 non-optical mouse 57 system board notices 71 connectors 22, 23 identifying parts 21 location 22, 23 memory 15, 22, 23, 24 Online Books folder 59...
  • Page 92 Part Number: 41X8069 Printed in USA (1P) P/N: 41X8069...

Table of Contents