Limitations; Controls And Settings - Lincoln Electric POWER-ARC IM871-A Operator's Manual

B-2
Physical Location of Components may vary by Code No.
FIGURE B.1 (For Codes 11182, 11187, 11215)
9
80
70
AMPS AMPS
AMPS AMPS
125 125
90 90
AMPS AMPS
AMPS AMPS
GENERATOR GENERATOR
100 100
AMPS AMPS
WARNING WARNING
2
ELECTRODE SELECTION GUIDE ELECTRODE SELECTION GUIDE
4
3
1. CURRENT CONTROL DIAL
2. ELECTRODE SELECTION GUIDE
3. WELD OUTPUT TERMINAL (TO ELECTRODE HOLDER) WITH
1/2 - 13 FLANGE NUT
4. WELD OUTPUT TERMINAL (TO WORK) WITH 1/2 - 13
FLANGE NUT
5. GROUND STUD
6. 20 AMP CIRCUIT BREAKERS (2)
7. 20 AMP, 240 VOLT RECEPTACLE
8. 20 AMP, 120 VOLT DUPLEX RECEPTACLE
9. TACHOMETER / HOURMETER (CODE 11215 ONLY)

LIMITATIONS

• The POWER-ARC 5500 is not recommended for
any processes besides those that are normally per-
formed using stick welding (SMAW) procedures.
• The POWER-ARC 5500 is not recommended for
pipe thawing.
• During welding, generator power is limited to 100
watts, and output voltages can drop from 120 to 80
volts and 240 to 160 volts. Therefore, DO NOT
OPERATE ANY SENSITIVE ELECTRICAL EQUIP-
MENT WHILE YOU ARE WELDING.

CONTROLS AND SETTINGS

All generator/welder controls are located on the
Output Control Panel. Gasoline engine controls are
mounted on the engine. See Figures B.1 and B.2 and
the explanations that follow.
OPERATION
OUTPUT PANEL CONTROLS
1
POWER ARC 55 POWER ARC 5 5 00 0 0
8
7
5
6
POWER-ARC 5500
(For Codes 11403, 11404)
FIGURE B.2
9
80
70
AMPS AMPS
AMPS AMPS
90 90
125 125
AMPS AMPS
AMPS AMPS
GENERATOR GENERATOR
100 100
AMPS AMPS
WARNING WARNING
2
ELECTRODE SELECTION GUIDE ELECTRODE SELECTION GUIDE
4
3
1. CURRENT CONTROL DIAL
2. ELECTRODE SELECTION GUIDE
3. WELD OUTPUT TERMINAL (TO ELECTRODE HOLDER) WITH
1/2 - 13 FLANGE NUT
4. WELD OUTPUT TERMINAL (TO WORK) WITH 1/2 - 13
FLANGE NUT
5. GROUND STUD
6. 20 AMP CIRCUIT BREAKER
7. 20 AMP, 240 VOLT RECEPTACLE
8. 20 AMP, 120 VOLT DUPLEX RECEPTACLE
9. TACHOMETER / HOURMETER (CODE 11404 ONLY)
GENERATOR/WELDER CONTROLS
See Figure B.1 for the location of the following fea-
tures:
1. CURRENT CONTROL DIAL: Adjusts continuous
current output. The amperages on the dial corre-
spond to the average amperages needed for spe-
cific Lincoln welding electrodes.
2. ELECTRODE SELECTION GUIDE: Provides rec-
ommended electrode type, size, and welder out-
put setting based on the thickness of the work.
3. WELD OUTPUT TERMINAL (TO ELECTRODE
HOLDER) WITH 1/2 - 13 FLANGE NUT: Pro vides
the connection point for either the electrode hold-
er or the work cable. (Because the POWER-ARC
5500 is an AC output machine, either output ter-
minal can be used for either cable.)
B-2
1
POWER ARC 5500 POWER ARC 5500
8
6
7
5