Advertisement
REFERENCE®
MOUNTING THE
SUBWOOFER
The 1000s and 1200s subwoofers can be
mounted from the outside of the
enclosure or from the inside of the
enclosure. Which- ever way you mount the
subwoofer, use the included foam
mounting gasket to ensure a leak-free
seal between the subwoofer frame and
the enclosure.
CONNECTING THE
SUB WOOFER
SETTING THE IMPEDANCE
The 1000s and 1200s subwoofers both
feature the Selectable Smart Impedance'"
(SSI)
switch.
This exclusive feature lets
you set the subwoofer's impedance to
either 2 ohms or 4 ohms with the flip of a
switch (see illustrations to the right). This
allows you to extract the most from your
subwoofer amplifier In any situation.
The SSI 2-ohm setting increases the
subwoofer's output over the 4-ohm
setting by up to 3dB, depending on the
amplifier. Performance is identical in all
SPECIFICATIONS
~
=
i j
~
=
//
1000s
10" (250mm)
20
~0
OJ
IMPEDANCE
2-0hm Setting
20
40
[0
IMPEDANCE
4-0hm Setting
Power Handling
(RMS):
Low-profile SSI Automotive Subwoofer
200W
Power Handling (Peak):
Sensitivity@ 2.83V /1m:
Frequency Response:
Impedance:
Voice-Coil Diameter:
Mounting Depth:
Overall Diameter:
Cutout Diameter:
BOOW
89dB
35Hz- 175Hz
2 or 4 ohms (selectable)
2" (50mm)
3-5/16" (83mm)
1 0-9/16" (268mm)
9-1/2" (240mm)
A valid serial number is required for warranty
coverage.
Features, specifications and appearance are subject to change without notice.
I
~
<{?
~
I
~
<{?
~
~
other respects. If the connected amplifier
is rated for 2-ohm operation and its 2-ohm
power ratings are within the subwoofer's
power-handling specifications, setting
the SSI switch in the 2-ohm position will
achieve maximum output.
IMPORTANT: Make sure the
subwoofer amplifier is turned OFF before
setting the SSI switch. Do not change the
switch position while the subwoofer
amplifier is operating. Doing so could
damage the amplifier.
CONNECTING THE AMPLIFIER
The Reference 1000s and 1200s subwoofer
connectors are compatible with quick-
disconnect (not supplied) or soldered
connections. The recommended wire gauge
is between 14AWG and BAWG, depending
on the length of the wire run between the
amplifier and woofer. Heavier gauge wire
is preferred for runs over 6' (2m).
1200s
12" (300mm)
Low-profile
SSI
Automotive Subwoofer
250W
1000W
92dB
27Hz
-
175Hz
2 or 4 ohms (selectable)
2"
(50mm)
3-5/16" (83mm)
12-1/4" (310mm)
11-1/8"
(282mm)
These
products
are designed for mobile applications and are not intended for connection to the
mains.
HARMAN
~Infinity,
HAR MA
N International Industries,
Inc.
8500 B
alboa Boulevard,
Northridge,
CA
91
329
U
SA
www.infinityspeakers.com
©
2014 Harman International Industries, Incorporated. All
rights reserved.
Infinity and R
eference are
tradem
arks
of Harman International Industries, Incorporated, registered in
the
United
S
tates
and/or other countries.
EN
The wider terminal is the positive and the
narrower is negative (also indicated on
the terminal
cover).
NOTE: If using untinned bare wire, be
sure that no stray"+" and "-" strands
touch each other. Touching strands can
cause a short circuit, which can damage
your amplifier.
-
Advertisement
