Countdown Timer; World Time - Casio 5129 Operation Manual

Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
Problem Probable Cause
•
I can't receive a time You performed some button operation
calibration signal. during auto receive.
• The watch is not in the Timekeeping Mode
or World Time Mode.
• The watch is in a location where the signal
cannot be received for some reason.
•
A countdown timer operation is in
progress.
• Radio interference is often present during
the day time, which can interfere with
signal reception.
•
The time setting is If the time is one hour off, the DST setting
incorrect following may be incorrect.
signal reception.
• The Home City code setting is not correct
for the area where you are using the
watch.
• The home positions of the hands are off.
•
For further information, see "Important!" under "Time Calibration Signal Reception" and "Radio-
controlled Atomic Timekeeping Precautions".

World Time

World Time digitally displays the current time in one of 48 cities (29 time zones)
Currently selected
around the world. A simple operation swaps your Home City with the currently
World Time City
selected World Time City.
• The times kept in the World Time Mode are synchronized with the time being
kept in the Timekeeping Mode. If you feel that there is an error in any World
Time Mode time, check to make sure you have the correct city selected as
your Home City. Also check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC offsets. See the "City
Code Table" for information about the UTC offsets that are supported.
• All of the operations in this section are performed in the World Time Mode,
which you enter by pressing C.
Right Dial Hand
World Time hour
The right dial hand shows the current hour in the World Time City in all modes.
• The right dial hand moves just like the normal hour hand, completing one
Current time in
revolution every 12 hours.
World Time City
•
Between the noon and midnight in the World Time Mode, a PM indicator
(PM ) appears above the right dial hand.
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• When the city code (time zone) you want is selected, you can press
one second, the watch will resume regular timekeeping.
Hour : Minutes Seconds
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press
whose Standard Time/Daylight Saving Time setting you want to change.
2. Hold down A for about three seconds to toggle between Daylight Saving
Time (DST indicator displayed) and Standard Time (DST indicator not
displayed).
DST indicator
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This changes your Home
City to your World Time City, and your World Time City to your Home City. This capability can come in
handy when you frequently travel between two cities in different time zones.
• If your current World Time City supports receipt of a time calibration signal, making it your Home City
enables calibration signal reception.
•
For information about which cities support time calibration signal reception, see "To specify your Home
City".
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Hold down A and B until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause the hour and
minute hands to move to the current time in that city. At the same time, it will change the Home City
you had selected prior to step 2 your World Time City, and cause the content of the upper and lower
displays to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World Time Mode with the
city that was selected as the Home City prior to step 2 now displayed as the World Time City.
Operation Guide 5129 (OC)
What you should do
•
Perform manual receive at night or wait
until the next auto receive operation is
performed.
•
Enter the Timekeeping Mode or World
Time Mode and try again.
• Enter the Countdown Timer Mode and
stop the countdown.
• Check to make sure the watch is in a
location where it can receive the signal.
•
Change the DST setting to Auto DST.
• Select the correct Home City code.
• Enter the home position adjustment
mode and adjust the home positions.
A to display the date. After about
Press A.
One second
Date
D to display the city code (time zone)
Stopwatch
The stopwatch lets you measure elapsed time, split times, and two
Hours
finishes.
• The digital display range of the stopwatch is 23 hours, 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero after it reaches its
limit, until you stop it.
• The stopwatch measurement operation continues even if you exit the
Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen on the display
clears the split time and returns to elapsed time measurement.
•
All of the operations in this section are performed in the Stopwatch
Mode, which you enter by pressing C.
Minutes SPL indicator
1/100 second
Seconds
To measure times with the stopwatch
Elapsed Time
D D
Start Stop
Split Time
D A
Start Split
(SPL indicator
displayed)
Two Finishes
D A
Start Split
First runner finishes.
Display time of first
runner.

Countdown Timer

You can set the countdown timer start time within a range of one minute to
Start time (minutes)
60 minutes. An alarm sounds when the countdown reaches zero.
• You also can select auto-repeat, which automatically restarts the countdown
from the original value you set whenever zero is reached.
• All of the operations in this section are performed in the Countdown Timer
Mode, which you enter by pressing C.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the
alarm will sound for 10 seconds or until you stop it by pressing any button.
Minutes
The countdown time is reset to its starting value automatically after the alarm
stops.
Seconds
•
When auto-repeat is turned on, the countdown will restart automatically
without pausing when it reaches zero. The alarm sounds to signal when the
Number of the current
countdown reaches zero. The countdown is repeated up to eight times, and
repeat
then stops.
• The number of the current repeat (1 to 8) is shown in the lower display.
•
The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• To stop a countdown timer operation completely, first pause it (by pressing
D), and then press A. This returns the countdown time to its starting value.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the Countdown Timer
Mode, hold down A for about three seconds until the minute setting of the
countdown start time starts to flash. This is the setting mode.
•
If the countdown start time is not displayed, use the procedure under "To
use the countdown timer" to display it.
2. Press C to move the flashing in the sequence shown below, and select the
setting you want to change.
Start time (minutes) Start Time (Minutes)
3. Perform the following operations, depending on which setting currently is selected on the display.
•
While the start time setting is flashing, use
• While the auto-repeat on/off setting ( 0N or 0FF) is flashing on the display, press D to toggle
auto-repeat on (0N) and off (0FF).
4. Press A to exit the setting mode.
• The auto-repeat on indicator ( ) will appear in the upper display while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
D D
Re-start Stop
A D
Split release Stop
D A
Stop Split release
Second runner Display time of
finishes. second runner.
C
Auto-Repeat On/Off
D (+) and B (–) to change it.
A
Clear
A
Clear
A
Clear
3