Lightolier Lighting Systems LFK1 Specification Sheet

4.295"
(10.91cm)
Ordering Information
Family Lamps
LFK 1
1 = 1 lamp per
4' (121.92cm)
Complete Ordering Instructions below.
Features
1. Extrusion: Extruded aluminum, painted white.
2. Housing: Multi-layered 5/8" (1.59cm) thick polycarbonate panels with patented
prism design. Clear outer layer and an opal non-glare inner layer. Light
transmission is 32% ASTM D1003 perpendicular to the panel. Reflectivity is
more than 40% perpendicular to the panel.
3. Endcap: Die cast aluminum, painted white.
4. Ballast Channel: Accepts linear fluorescent ballasts up to 1.2" (3.05cm) wide
by 1.2" (3.05cm) tall.
5. Lamp: T5 linear fluorescent, 28 or 54 watt. (by others).
Electrical
Ballast: Electronic and meets A.N.S.I. starting, end of life protection, T.H.D., "A"
sound rating, and end-of-life specifications. Factory installed ballast disconnect
allows the ballast to be disconnected from and reconnected to incoming power
under load without turning the entire circuit off.
Wiring: 3 Conductor 18 gauge wire. Color-coded quick connectors allow ease of
connection for fixture modules.
Dimming: Advance Mark X. Use Advance compatible 2 wire control (no extra lead
is required in the luminaire).
Emergency Battery Pack: 54 Watt: 390-700 Lumens for 90 minutes,
28 Watt: 370-520 Lumens for 90 minutes.
Dual Switching: Order the DS option for separate row switching. DS option
comes complete with the 4th through wire option.
4 and 5 wire: Order X4 for EM Battery Pack. For non-standard dimming options
order X5 option for Osram or DALI 54 watt dimming, X4 option for Lutron HiLume
or ECO-10 54 Watt dimming.
Consult Factory for any additional wiring conditions.
Finish
Powder coated white baked enamel. Custom colors available, consult factory.
4.895" (12.43cm)
3.400"
(8.64cm)
Shielding Wattage
N
N = No 28 = 28w T5
Sheilding 54 = 54w T5
2D = 28w T5 Dimming
5D = 54w T5 Dimming
2E = 28w T5 Emergency Pack
5E = 54w T5 Emergency Pack

Lighting Systems

1 2
Half Scale
5 4 3
Voltage
1 = 120v 4 = 4' (121.92cm)
2 = 277v 8 = 8' (243.84cm)
Mounting
Mounting locations are adjustable along the top of the extrusion. Cable suspension
(not shown) consists of 4 1/2" (11.43cm) diameter canopy finished white enamel,
1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"
(91.44cm). Draw-tight connector to create hairline seam between joiner modules.
Modules allow 6" (15.24cm) of suspension position adjustment.
Ordering Instructions
Individual Fixtures:
1. Order number of MODULES required.
2. Order one POWER FEED CABLE END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED CABLE END SET per run.
4. Order one INTERMEDIATE CABLE SET per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate number of
CABLE/CORD SET.
Labels
UL , cUL and I.B.E.W. Patent Applied For.
Job Information
Job Name:
Cat. No.:
Lamp(s):
Notes:
We reserve the right to change details of design, materials and finish.
LFK1
Length
Options
DS = Dual Switch
X4 = 4 Through Wires
X5 = 5 Through Wires
Type: