Advertisement
Quick Links
I
MPORTANT
WARNING: Before installation, disconnect power at circuit breakers or remove fuse to avoid electrical
shock or damage to the unit. It is recommended that an electrician perform this installation.
Made in U.S.A.
M
S
P
ULTI
ET
: R
ETAIN THESE INSTRUCTIONS FOR THE END USER
1
2
3
4
5
M
S
ULTI
ET
D
IMMING
C
M
OMPATIBLE WITH
ULTI
MHP5ES, MHP8ES, MPH5AVES, MHP8AVES, MHP600VA, MHP1000VA, MHP1500VA,
MHP2000VA, MHP1000ND, MHP2000ND, MHP500QE, MHP600HDF120,
MHP1500HDF120, MHP600EB, MHP1000EB, MHP1500EB, MHPWHIS
- P
-W
®
RO
RE
IRED
A
B
C
D
P
® - P
-W
RO
RE
C
MDC20
ABINET
S
P
® H
D
ET
RO
EATSINK
For technical/sales assistance, call: 1-800-526-2731
D
C
IMMING
ABINET
I
NSTALLATION AND
O
. DO NOT DISCARD.
IRED
M
:
IMMER
ODELS
www.lolcontrols.com P/N 85-1530
MDC20
PERATIONS
M
ANUAL
Advertisement
Summary of Contents for Lightolier MULTISET PRO MDC20
- Page 1 MPORTANT ETAIN THESE INSTRUCTIONS FOR THE END USER OMPATIBLE WITH MHP5ES, MHP8ES, MPH5AVES, MHP8AVES, MHP600VA, MHP1000VA, MHP1500VA, MHP2000VA, MHP1000ND, MHP2000ND, MHP500QE, MHP600HDF120, MHP1500HDF120, MHP600EB, MHP1000EB, MHP1500EB, MHPWHIS WARNING: Before installation, disconnect power at circuit breakers or remove fuse to avoid electrical shock or damage to the unit.
- Page 2 3. Use Quiet Electronic (QE) Dimmers to control only low-voltage fixtures that have electronic, solid-state transformers, and regular incandescent loads. Not for use with Magnetic Low Voltage fixtures. 4. Use HDF Direct Drive Dimmers to control fluorescent lighting loads at 120V with approved Lightolier® Controls PowerSpec® HDF Electronic Ballasts only, and Lightolier® Controls Dimming Amplifiers.
-
Page 3: Cabinet Installation
Terminal Blocks: Load wire terminations - Black Terminal Blocks: Power feed terminations - Blue Terminal Block: MultiSet Pro purple wire terminations - White Terminal Block: Neutral wire terminations - Grey Terminal Block: Lightolier Controls PowerSpec HDF dimming ballast TAN wire termination. MDC20... - Page 4 ® ULTI Replacing the Keypad Button Labels (Classic Series) MultiSet Pro® Classic Series Masters are supplied with over 260 labels to personalize the buttons for your own scene names. The buttons are labeled at the factory with letters. These button labels can easily be changed to customize your system: 1.
- Page 5 Installation and Operation Dimmer/Switch Operating Instructions ® D ULTI IMMER • To Turn light on to preset level, tap top of rocker, the dimmer fades up at the 1.5 second rate. • A second tap of the rocker fades the dimmer to full brightness. •...
- Page 6 ® ULTI Changing the Fade Rate MultiSet Pro® Dimmers can be programmed for 12 different fade rates. Dimmers can be programmed to have a different fade rate on each scene. The fade rate choices are: 1.5 seconds minute seconds minutes 4.5 seconds minutes 7.5 seconds...
-
Page 7: Typical Wiring Diagram
Installation and Operation Setting the Button Brightness (Ellipse Series) The brightness level of each Ellipse Master Control Station button can be programmed to 100% (factory default), 75%, 50%, or 25%. To change the setting: 1. On a 5-Scene Master, press and hold buttons “B” and “D” simultaneously for 3 seconds (on an 8- Scene Master, press buttons “H”... -
Page 8: Cabinet Specifications
Lightolier Controls’ sole obligation will be at its option to repair or replace any electronic controls product proven defective if it is returned, postage prepaid, to Lightolier Controls, 10911 Petal St. Dallas, Texas 75238. Lightolier Controls will not pay for any charge-back or charge for labor or material that does not have its prior written approval.