(MFR’S VERSION A) SERVICE MANUAL COLOR TELEVISION 30DF56 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
TABLE OF CONTENTS GREEN PRODUCT PROCUREMENT ..................A1-1 LEAD-FREE SOLDER ........................ A1-1 SERVICING NOTICES ON CHECKING ..................A1-2 HOW TO ORDER PARTS ......................A1-2 IMPORTANT ..........................A1-2 TABLE OF CONTENTS ......................A2-1 GENERAL SPECIFICATIONS ....................A3-1~A3-5 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ....................B1-1 2.
GENERAL SPECIFICATIONS CRT Size / Visual Size 30 inch / 760mmV System CRT Type Flat (16:9) Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Display Capability 480i Speaker 2 Speaker Position Front Size 1.8 x 3.9 Inch Impedance Sound Output 2.5W+2.5W 10%(Typical) NTSC3.58+4.43 /PAL60Hz Tuning...
Page 6
GENERAL SPECIFICATIONS Remote Unit RC-KK Control Glow in Dark Remocon Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys Keys Power TV/VIDEO Recall Mute 100 / +10...
Page 7
GENERAL SPECIFICATIONS G-10 Features Picture Brightness, Contrast, Color, Tint, Sharpness Mode (Picture preference) Color Temperature Audio Tone Control (Bass, Treble, Balance) Surround Stable Sound SRS WOW(SRS 3D/Focus/Tru Bass) Variable Audio Out Tuning TV/CABLE CH Program Add/ Delete Label CH Label Video Label Favorite CH Lock...
Page 8
GENERAL SPECIFICATIONS G-11 Accessories Owner's Manual Language English / Spanish W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Station List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter...
Page 9
40 (ORION SPEC:25) Container Stuffing Sets/40' container G-16 Material Cabinet Cabinet Front PS 94V0 DECABROM Cabinet Rear PS 94V0 NON-DECABROM Non-Halogen Demand Eyelet Demand G-17 Environment Environmental standard requirement (by buyer) Green procurement of TOSHIBA Pb-free Phase3(Phase3A) Measures for Whisker A3-5...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS When IC starts moving back and forth easily after REMOVAL AND INSTALLATION OF desoldering completely, pickup the corner of the IC using a FLAT PACKAGE IC tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 12
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.) IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
Page 14
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. Table 1 CONFIRMATION OF INITIAL DATA Enter DATA SET mode by setting VOLUME to minimum.
RE-WRITE FOR DIGITAL SOFT FIRMWARE JG198 JG199 Flash UP-Date Soft JG176 USA SD DTV ROM Serial Communication Disc DISC Change JIG Ref. No. Part No. Parts Name Remarks Serial Communication JG198 APJG198000 Connect the set to personal computer Change JIG Up-Date of the Firmware JG199 APJG199000...
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE FUNCTION FUNCTION FUNCTION OSD H COR BTM COL.MIN Read and perform these adjustments when repairing the OSD C S CORR TINT CENT circuits or replacing electrical parts or PCB assemblies. CUT OFF CORNER SHARP.CENT H.POSI C PARA SHARP.MAX CAUTION...
Page 17
ELECTRICAL ADJUSTMENTS 2-4: WHITE BALANCE 2-6: CONTRAST MAX Receive an over 70dB color bar pattern. (RF Input) NOTE: Adjust after performing CUT OFF adjustment. Press the PIC SIZE button on the remote control to select Place the set in Aging Test for more than 15 minutes. the FULL screen mode.
Page 18
ELECTRICAL ADJUSTMENTS 2-7: TINT 2-8: COLOR CENT Receive the color bar pattern. (RF Input) Receive the color bar pattern. (RF Input) Press the PIC SIZE button on the remote control to select Press the PIC SIZE button on the remote control to the FULL screen mode.
Page 19
ELECTRICAL ADJUSTMENTS 2-9: HORIZONTAL POSITION horizontal line Receive the monoscope pattern. Press the PIC SIZE button on the remote control to select the FULL screen mode. Notch Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to Shadow mask select “H.POSI”.
Page 20
ELECTRICAL ADJUSTMENTS 2-16: COR TOP/BTM Receive the crosshatch signal from the Pattern Generator. Press the PIC SIZE button on the remote control to select the FULL screen mode. Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig.
Page 21
ELECTRICAL ADJUSTMENTS 2-19: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment items are set correctly referring below. (TV/AV/YUV/DIGITAL) FULL NATURAL DIGITAL DIGITAL FUNCTION Step No. Step No. Step No. Step No. Step No.
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
WAVEFORMS DEFLECTION CHROMA/IF 10ms 20µs 10µs 0.5V 20.0V 200mV 2µs 50µs 0.5V 20µs 10.0V 20µs 20µs 10µs 20.0V 200mV AV SW/SOUND AMP/TONE CTL 20µs 200mV 20µs 20µs 10.0V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS CRT/SVM 20µs 20µs 200mV MICON 50µs 20µs 20µs 50µs 50µs 50µs NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.