1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Speakers
  5. XY Series
  6. Installation manual

Pioneer XY series Installation Manual

Hide thumbs Also See for XY series:
Table of Contents

Advertisement

Quick Links

Download this manual
XY-81
8-inch two-way loudspeaker
XY-101
10-inch two-way loudspeaker
XY-122
12-inch two-way ｌoudspeaker
XY-152
15-inch two-way ｌoudspeaker
XY-115S
15-inch bass reflex Subwoofer
XY-118S
18-inch bass reflex Subwoofer
XY-215S
Dual 15-inch quasi-bandpass subwoofer
XY-218S
Dual 18-inch bass reflex Subwoofer
Loudspeaker XY Series

Installation manual

http://pioneerproaudio.com/
Version 2.1 September 2014
©2014 PIONEER CORPORATION
All right reserved

Advertisement

Table of Contents
loading

Related Manuals for Pioneer XY series

Summary of Contents for Pioneer XY series

  • Page 1: Installation Manual

    Loudspeaker XY Series Installation manual http://pioneerproaudio.com/ XY-81 8-inch two-way loudspeaker XY-101 10-inch two-way loudspeaker XY-122 12-inch two-way ｌoudspeaker XY-152 15-inch two-way ｌoudspeaker XY-115S 15-inch bass reflex Subwoofer XY-118S Version 2.1 September 2014 18-inch bass reflex Subwoofer XY-215S Dual 15-inch quasi-bandpass subwoofer ©2014 PIONEER CORPORATION...

  • Page 2: Table Of Contents

    Contents 1 Introduction 1.1 Before you start 1.2 Installation guidelines 1.3 System set-up 2 Accessories 3 Rigging And Caster Setting 3.1 Before Setting 3.1.1 Guide for safe use 3.1.2 Horn rotation 3.1.3 Logo badge replacement 3.2 Procedures 3.2.1 Vertical Flying Cradle 3.2.2 Horizontal Flying Cradle 3.2.3 Variable Angle Bracket 3.2.4 Dual Enclosure Flying Plate Set(*Dual + Variable)

  • Page 3: Introduction

    Make sure to secure each device in place using the pole mount, ratchet straps or other hardware to prevent them from tipping over or falling when stacking devices together. Pioneer shall accept no liability for damage or injury caused by accidents resulting from Pioneer products tipping over or falling due to them being insufficiently secured.

  • Page 4: About Trademarks And Registered Trademarks

    ・ Do not attempt to use the product with the XY Series grille detached as doing so could result in damage to the product. Consult a qualified professional for assistance with removing the grille for maintenance purposes.

  • Page 5: Installation Guidelines

    1 Introduction ____________________________________________________________________________________________________________ 1.2 Installation guidelines WARNING ・ Ensure that the floor or stage surface in question can withstand the weight of the system. Consult a qualified professional for advice if the strength of the surface is unknown. ・ After installation, you must confirm that the speakers are safely installed. You must also periodically check them to make sure that they are still safe.

  • Page 6: System Set-Up

    1 Introduction ____________________________________________________________________________________________________________ 1.3 System set-up WARNING ・ Loudspeaker systems are potentially dangerous objects if used incorrectly. Please ensure that you read this section fully, and contact your local dealer should you be in any doubt over correct operation procedures. ・...

  • Page 7: Accessories

    A safety steel can then be attached to this and connected to your safety point. Hardware standby The following hardware is provided with the XY series products so that commercially-available poles, brackets and other items can be attached. (see Table 2-1 and 2-2 "Hardware standby") ・Check to make sure that any commercially available mounting hardware used is enough to support the...
  • Page 8 2 Accessories __________________________________________________________________________________________________________ Table 2-1 Two-way loudspeaker XY-81 XY-101 XY-122 XY-152 4 × M6 4 × M8 Wall Mount Bracket threaded <- threaded <- points points Eyebolts M8(*2) <- M10 (*3) <- Hardware 35 mm standby Speaker Pole polemount <- <- <- socket...
  • Page 9 2 Accessories __________________________________________________________________________________________________________ White socket cover seal for the white models Applicable models: XY-81-W : 1 piece of white seal is shipped with XY-81-W. XY-101-W : 1 piece of white seal is shipped with XY-101-W. XY-122-W : 1 piece of white seal is shipped with XY-122-W. XY-152-W : 1 piece of white seal is shipped with XY-152-W.

  • Page 10: Rigging And Caster Setting

    WARNING: INTENDED USAGE Do not use any other method than the one prescribed in this manual. The XY Series rigging components must only be used in conjunction with the XY Series loudspeakers. SAFETY CAUTIONS Ensure and check all the speaker riggings are sufficiently secure to be used before using them.
  • Page 11 3 Rigging And Caster Setting __________________________________________________________________________________________________________ CAUTION: PREPARING THE CABINET Pre-inserted M10 and M8 screws are mounted in the top, bottom, rear, left and right side of the loudspeaker enclosure. These screws are painted in the cabinet color. Follow the steps below to ensure the cabinet paint is not peeled off during unscrewing.

  • Page 12: Horn Rotation

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.1.2 Horn rotation HF dispersion orientation on XY-81/101/122/152 can be changed by rotating the HF waveguide 90 degrees. (Fig.3-1-3-A) NOTE: XY-122 is shown in the illustration 90 deg 60 deg After rotating Factory default 90 deg 60 deg the waveguide...
  • Page 13 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Lift the waveguide up and rotate it 90 degrees to change the dispersion orientation depending on the orientation of the enclosure. When the HF waveguide is rotated back to the original orientation, ensure it is rotated in the reverse direction when it was first rotated.

  • Page 14: Logo Badge Replacement

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.1.3 Logo badge replacement The location of Logo badge attached to the grilles on XY-81/101/122/152 can be changed. Required tools XY-81 / XY-101 XY-122 / XY-152 ・Phillips head screwdriver ・3mm hex key ・Phillips head screwdriver ・4mm hex key Procedure NOTE: XY-122 is shown in the illustration...
  • Page 15 3 Rigging And Caster Setting __________________________________________________________________________________________________________ CAUTION: XY-81/101 Location where the Logo badge should be attached: The Logo badge can be attached to only the limited locations on the grille. Please see the Fig.3-1-3-F, G, H, I. If the Logo badge is attached to other locations than the specified ones, the speaker could be damaged.
  • Page 16 3 Rigging And Caster Setting __________________________________________________________________________________________________________ 8 holes Bottom 8 holes DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE A plate supporting the grille A plate supporting the grille DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE 5 holes 9 holes...
  • Page 17 3 Rigging And Caster Setting __________________________________________________________________________________________________________ XY-101 DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH DO NOT ATTACH THE LOGO BADGE THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH holes THE LOGO BADGE A plate to support the DO NOT ATTACH THE LOGO BADGE.

  • Page 18: Procedures

    3 Rigging And Caster Setting _________________________________________________________________________________________________________ 3.2 Procedures 3.2.1 Vertical Flying Cradle When using the Vertical Flying Cradle, suspension of the XY-81/101/122/152 To the ceiling enclosure vertically from the ceiling as shown in the right figure is available. Speaker models compatible with respective Vertical Flying Cradles are shown in the table below.
  • Page 19 3 Rigging And Caster Setting _________________________________________________________________________________________________________ Part list (CP-XY8VC1) Required tools Note Item Part Name Service Part No. ・Screwdriver Vertical Flying Cradle Outer Yoke Inner Yoke Neoprene Washer 05B010 40mm x 2mm Flat Washer 06D009 Spring Washer 06D011 ・5mm hex key Knob 05A101 M8 x 30mm (P=1.25)
  • Page 20 3 Rigging And Caster Setting _________________________________________________________________________________________________________ Procedure (CP-XY8VC1/XY10VC1/XY12VC1/XY15VC1) NOTE: XY-122 is shown in the illustrations below. Remove the pre-inserted mounting screws from the top of enclosure. The number of screws to be removed from XY-81/101/122 is 2 (The location is shown in Fig.3-2-1-A) and from XY-152 is 4. Only XY-152 NOTE: In addition, Using the supplied two M10 socket head bolts(E), align the mounting holes in the load plate(F) with the mounting point on...
  • Page 21 3 Rigging And Caster Setting _________________________________________________________________________________________________________ Once the desired angle of the loudspeaker is set, tighten the knobs/levers on the cradle to lock the position in place. (Fig.3-2-1-E) Commercially- The hole on the outer yoke of the Vertical Flying Cradle (A) can be used available to install the speaker to the ceiling.

  • Page 22: Horizontal Flying Cradle

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.2.2 Horizontal Flying Cradle When using the Horizontal Flying Cradle, suspension of the XY- NOTE: XY-122 is shown in the illustration. 81/101/122/152 enclosure horizontally from the ceiling or the wall as shown in the right figure is available. The orientation of the enclosure can be To the ceiling changed at any angle.

  • Page 23: Required Tools

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ WARNING: Horizontal Flying Cradle is not supposed to be used in the following situations, which may cause an injury or accident. For ALL the models, the following situations are quite dangerous. The outer yoke of the The enclosure is not Suspending cradle is not vertical to...
  • Page 24 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Part list (CP-XY12HC1/CP-XY15HC1) Required tools Item Part Name Service Part No. Note ・screwdriver Horizontal Flying Cradle Main Yoke Mounting Plate Neoprene Washer 05B010 40mm x 2mm Flat Washer 06D014 ・8mm hex key Spring Washer 06D015 Lever 05A103...
  • Page 25 3 Rigging And Caster Setting __________________________________________________________________________________________________________ XY-152: Using the supplied M10 hex socket head bolts(B), align the mounting holes in the end mounts of the plate of the Horizontal Flying Cradle(A) with the mounting points on the top and the bottom of the enclosure. WARNING: The mounting plate of Horizontal Flying Cradle should be installed to the XY-152 enclosure in a LONG...

  • Page 26: Variable Angle Bracket

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.2.3 Variable Angle Bracket NOTE: XY-122 is shown in the illustration. When using the Variable Angle Bracket, suspension of the enclosure vertically To the ceiling from the ceiling as shown in the right figure is available. It is easier to change the inclined angle of Variable Angle Bracket than that of Vertical Flying Cradle.
  • Page 27 3 Rigging And Caster Setting __________________________________________________________________________________________________________ WARNING: Variable Angle Bracket is not supposed to be used in the following situations, which may cause an injury or accident. Not suspending Suspending Suspending from the wall Multiple enclosures vertically Part list (CP-XY12AB1/CP-XY15AB1) Required tools Note Item Part Name...
  • Page 28 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Procedure NOTE: XY-122 is shown in the illustration. Remove the two pre-inserted mounting screws on the top of enclosure. (Fig.3-2-3-B) Using the supplied M10 hex head bolts(D), align the mounting holes in the Variable angle bracket(A) with the mounting points on the top of the enclosure.
  • Page 29 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Remove the pre-inserted M10 mounting screw on the either right or left mounting point on the top of the XY-122/152 enclosure. Ensure the commercially-available eyebolt are secured to either right Commercially -available or left mounting point on the top of the enclosure to suspend it with eyebolt wire as a secondary safety feature.

  • Page 30: Dual Enclosure Flying Plate Set(*Dual + Variable)

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.2.4 Dual Enclosure Flying Plate Set When using the Dual Enclosure Flying Plate Set, two enclosures can be stably To the ceiling combined side by side and vertically or horizontally suspended from the ceiling (Vertical) as shown in the figure below.
  • Page 31 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Part list (CP-XY12DF1/CP-XY15DF1) Required tools Note Item Part Name Service Part No. ・Screwdriver Dual Enclosure Flying Plate M10 x 40mm (P=1.5), M10 socket head bolt 06G053 8mm hex socket head Spring washer 06D015 Flat washer 06D014 ・8mm hex key 06E012...
  • Page 32 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Vertical installation Once the desired angles of the two XY-122/152 are set, fully tighten all the M10 socket head bolts(B) on both the top and the bottom of the enclosure to lock the position in place. The three M10 holes on the top of the Dual enclosure flying plate can be used to install the speaker to the ceiling as shown in the figure.
  • Page 33 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Remove the four pre-inserted M10 mounting screws on the rear side of XY-122/152 enclosure. Ensure the four commercially-available M10 eyebolts are secured to the mounting points on the rear side of the XY-122/152 enclosures to suspend it with wire as a secondary safety feature.
  • Page 34 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Part list Dual Enclosure Flying Plate Set (CP-XY12DF1/CP-XY15DF1) Required tools Note Item Part Name Service Part No. ・Screwdriver Dual Enclosure Flying Plate M10 x 40mm (P=1.5), M10 socket head bolt 06G053 8mm hex socket head Spring washer 06D015 Flat washer...
  • Page 35 3 Rigging And Caster Setting __________________________________________________________________________________________________________ XY-152: Using the supplied M10 hex head bolts(L) and the Nuts(E) align the two M10 holes in the center of the Dual enclosure flying plate(A) with the mounting points of the Variable angle bracket(I). WARNING: Please look carefully at the illustration below before installing the Variable Angle Bracket to the plate and place the Variable Angle Bracket in the right position to align its front and the...
  • Page 36 3 Rigging And Caster Setting __________________________________________________________________________________________________________ Note: ・ When the hook clamp is mounted in the very rear mounting point, the inclined angle of the both enclosures is shown below. 36 deg(XY-122) and 29 deg(XY-152) when the angle between the two enclosures is at 50 deg (minimum degrees) and 29 deg(XY-122) and 22 deg(XY-152) when the angle between them is at 95 deg (maximum degrees).

  • Page 37: Suspension Of Enclosure Using The Eye Bolt

    3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.2.5 Suspension of the enclosure using the eyebolt The XY-81/101/122/152 enclosure has the mounting points where NOTE: XY-122 is shown in the illustration. commercially-available eyebolts can be mounted. Using the commercially- To the ceiling available eyebolts, a XY-81/101/122/152 enclosure or a combination of them (Vertical) can be vertically or horizontally suspended.
  • Page 38 3 Rigging And Caster Setting __________________________________________________________________________________________________________ WARNING: Limits of combining multiple speakers ・ Be sure to meet the conditions and requirements shown in the Table.3-2-5-B. Table.3-2-5-B: Limits and requirements of combining multiple speakers using eyebolts Max. working load Model Max. No. of Enclosures Min. No. of Suspension Lines limit/mounting point XY-81 Three,...

  • Page 39: Wall Mount Bracket

    The holes for commercially-available wall mount brackets are provided on the rear of the XY-81/101/122/152. Note: Pioneer does not sell wall mount brackets. Please ensure that the commercially-available wall mount bracket is compatible with the sizes shown in Table 3-2-6-A Table 3-2-6-A: Size of the hole and the area for a wall mount bracket to be attached.

  • Page 40: Caster

    3 Rigging And Caster Setting ___________________________________________________________________________________________________________ 3.2.7 Caster The mounting points for casters to help moving the loudspeakers are on NOTE: XY-118S is shown in the illustration. the rear side of XY-118S/215S/218S. Part list (CP-XYCS1) Required tools Item Part Name Service Part No.

  • Page 41: System Configuration

    Power Amplifier Recommendations In order to deliver best audio quality, amplifiers made by Powersoft is recommended to be used with the XY series loudspeakers. Please refer to the table below for the combination of amplifiers with respective loudspeakers. Table 4-1-1 Two-way loudspeaker...
  • Page 42 Using wrong pinouts may cause damage to the speakers or occur accidents. The XY Series are supplied as standard with Neutrik SpeakON™ NL4 connectors, wired pin 1+/1–. It is recommended that the resistance of your cable be less than one tenth of the nominal system impedance.
  • Page 43 K-Series and M-Series have different pinouts for the Neutrik SpeakON™ connectors(NL4) for Power Amplifier. K-Series M-Series inverting inverting Cable specification An example of the cable connecting XY Series products and amplifiers of K-Series or M-Series is shown below. SpeaKON SpeaKON Speaker Cable(2 core) (NL2 or NL4) (NL2 or NL4)

  • Page 44: System Setting

    Please see the [Armonia User Guide] of Powersoft for details of how to set and use the Preset and the Amplifier. http://www.powersoft-audio.com/en/ URL: http://www.powersoft-audio.com/en/products/software.html Please see the Pioneer website for the details of Presets and the specifications of the setting values. http://pioneerproaudio.com/en/resources.html URL: ・The audio quality may vary depending on the environment and the location where the NOTES: loudspeakers are placed even though the presets are made optimal for universal use.
  • Page 45 4 System Configuration ____________________________________________________________________________________________________________ XY-81(Stereo) with XY-115S(MonoMix) Fig.4-2-A XY-81 XY-81 K2DSP XY-115S XY-115S K3DSP Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-81 KDSP_XY-81_for_XY-115S_V1.0 XY-81 from both channels 1 & 2 of the K2DSP XY-81 amplifier combine with XY-115S Mono mixed Subwoofer output to XY-115S...
  • Page 46 4 System Configuration ____________________________________________________________________________________________________________ XY-81(Stereo) with XY-215S(MonoMix) Fig.4-2-C XY-81 XY-81 K2DSP XY-215S K3DSP XY-215S Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-81 KDSP_XY-81_for_XY-215S_V1.0 XY-81 from both channels 1 & 2 of the K2DSP XY-81 amplifier combine with XY-215S Mono mixed Subwoofer output to XY-215S...
  • Page 47 4 System Configuration ____________________________________________________________________________________________________________ XY-101(Stereo) with XY-118S(MonoMix) Fig.4-2-E K2DSP XY-118S XY-118S K3DSP Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-101 KDSP_XY-101_for_XY-118S_V1.0 XY-101 from both channels 1 & 2 of K2DSP XY-101 the amplifier combine with XY-118S Mono mixed Subwoofer output to XY-118S KDSP_XY-118S_for_XY-101_V1.0...
  • Page 48 4 System Configuration ____________________________________________________________________________________________________________ XY-122(Stereo) with XY-115S(MonoMix) Fig.4-2-G XY-122 K3DSP XY-122 XY-115S XY-115S K3DSP Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-122 KDSP_XY-122_for_XY-115S_V1.0 XY-122 from both channels 1 & 2 of K3DSP XY-122 the amplifier combine with XY-115S Mono mixed Subwoofer output to XY-115S KDSP_XY-115S_for_XY-122_V1.0...
  • Page 49 4 System Configuration ____________________________________________________________________________________________________________ XY-122(Stereo) with XY-215S(MonoMix) Fig.4-2-I XY-122 K3DSP XY-122 XY-215S K3DSP XY-215S Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-122 KDSP_XY-122_for_XY-215S_V1.0 XY-122 from both channels 1 & 2 of K3DSP XY-122 the amplifier combine with XY-215S Mono mixed Subwoofer output to XY-215S KDSP_XY-215S_for_XY-122_V1.0...
  • Page 50 4 System Configuration ____________________________________________________________________________________________________________ XY-152(Stereo) with XY-118S(MonoMix) Fig.4-2-K XY-152 K3DSP XY-152 XY-118S K3DSP XY-118S Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-152 KDSP_XY-152_for_XY-118S_V1.0 XY-152 from both channels 1 & 2 of K3DSP XY-152 the amplifier combine with XY-118S Mono mixed Subwoofer output to XY-118S KDSP_XY-118S_for_XY-152_V1.0...
  • Page 51 4 System Configuration ____________________________________________________________________________________________________________ XY-152(Stereo) with XY-218S(MonoMix) Fig.4-2-M XY-152 K3DSP XY-152 XY-218S K6DSP XY-218S Recommended Connected Preset name Description Amp Model Speaker Mid/High frequency output to drive XY-152 KDSP_XY-152_for_XY-218S_V1.0 XY-152 from both channels 1 & 2 of K3DSP XY-152 the amplifier combine with XY-218S Mono mixed Subwoofer output to XY-218S KDSP_XY-218S_for_XY-152_V1.0...
  • Page 52 4 System Configuration ____________________________________________________________________________________________________________ Table 4-2-1 XYseries preset-files list for KDSP amplifier(Two-way loudspeaker) Recommended Connected Connection Preset name Description Amp Model Speaker chart XY-81 Full range output to drive XY-81 from KDSP_XY-81_V1.0 K2DSP both channels 1 & 2 of the amplifier. XY-81 Mid/High frequency output to drive XY-81 XY-81...
  • Page 53 4 System Configuration ____________________________________________________________________________________________________________ Table 4-2-2 XYseries preset-files list for KDSP amplifier(Subwoofer) Recommended Connected Connection Preset name Description Amp Model Speaker chart Mono mixed Subwoofer output to drive XY-115S KDSP_XY-115S_V1.0 K3DSP XY-115S from both channels 1 & 2 of the XY-115S amplifier.
  • Page 54 4 System Configuration ____________________________________________________________________________________________________________ Table 4-2-2 XYseries preset-files list for MHDSP amplifier Recommended Connected Connection Preset name Description Amp Model Speaker chart XY-81 Full range output to drive XY-81 from MHDSP_XY-81_V1.0 both channels 1 & 2 of the amplifier. XY-81 Mid/High frequency output to drive XY-81 XY-81 MHDSP_XY-81_for_XY-115S_V1.0...
  • Page 55 4 System Configuration ____________________________________________________________________________________________________________ Ground stacking ・Ensure that the floor or stage surface can withstand the weight of the system. CAUTION ・Do not carry out the stack with more than of specifications shown below. ・Use ratchet straps to secure loudspeakers together. ・Please also remember that vibrations from subwoofer systems can shake　other loudspeakers out of place, which may present a toppling hazard.

  • Page 56: Drive Unit Replacement

    Guide for safe replacement of the drive units Improper installation of the driver unit could cause them to fall and cause damage or injuries to persons nearby. Please check the following conditions of all the loudspeakers in the XY series always before the drive units are replaced.
  • Page 57 5 Drive unit replacement __________________________________________________________________________________________________________ XY-101 Note Item Part Name Service Part No. Required tools ・3mm hex key Grille 04X907 Grille M4 x 20mm (P=0.7) M4 socket head bolt 06G016 3mm hex socket head HF drive unit XY-81 Note Item Part Name Service Part No.
  • Page 58 5 Drive unit replacement __________________________________________________________________________________________________________ Procedure (XY-81/101) NOTE: XY-81 is used in the pictures. Removing and reinstalling the grille. Remove the four socket head bolts from the grille. Remove the grille from the enclosure. Reverse the above steps when placing the grille back to the enclosure.
  • Page 59 5 Drive unit replacement __________________________________________________________________________________________________________ Replacement of LF drive unit LF driver units installed in XY-81 and XY-101 are different, but almost the same procedures can be used to replace both LF drive units. Remove the socket head bolts from the LF drive unit. The number of socket head bolts to be removed from XY-81 is 8 and from XY-101 is 4.
  • Page 60 5 Drive unit replacement ___________________________________________________________________________________________________________ 5.1.2 XY-122/152 Part list Grille XY-122 Required tools Note Item Part Name Service Part No. ・4mm hex key Grille 04X902 M6 x 30mm (P=1.0), Grille M6 countersunk bolt 4mm hex socket head, 06G020 for grille XY-152 Required tools Note...
  • Page 61 5 Drive unit replacement ___________________________________________________________________________________________________________ HF waveguide/HF driver unit installed in XY-122 and XY-152 are the same, so the same procedures should be taken to replace them. Remove eight countersunk bolts from the HF waveguide. Lift the waveguide up and remove the cables from the HF drive unit. Remove the four nuts from the HF drive unit with a 10mm Spanner.
  • Page 62 5 Drive unit replacement ___________________________________________________________________________________________________________ Tighten the eight socket head bolts on the LF drive unit. NOTE: XY-122 is used in the pictures. Ensure that the terminals of the drive unit are placed as shown below. Location of Tighten the countersunk bolts to ensure a solid fit to the grille. terminals Additional information (XY-122/152) For the connection information, please refer to following circuit diagram.

  • Page 63: Subwoofer

    5 Drive unit replacement ___________________________________________________________________________________________________________ 5.2 Subwoofer 5.2.1 XY-115S/118S/218S Part list Grille XY-115S Required tools Item Part Name Qty Service Part No. Note ・Phillips head screwdriver Grille 04X909 For XY-115S Grille Screw 06F002 for grille, XY-115S XY-118S Required tools Item Part Name Qty Service Part No.
  • Page 64 5 Drive unit replacement ___________________________________________________________________________________________________________ Procedure (XY-115S/118S/218S) NOTE: XY-118S is used in the pictures. Removing and reinstalling the grille. Remove the screws from the grille. 12 pieces of screws for XY-115S, 14 pieces of screws for XY-118S and 24 pieces of screws for XY-218S are required to be removed. Remove the grille from the enclosure.
  • Page 65 5 Drive unit replacement ___________________________________________________________________________________________________________ XY-218S Location of Location of terminals terminals Additional information (XY-115S/118S/218S) For the connection information, please refer to following circuit diagram. XY-115S/118S XY-218S...

  • Page 66: Xy-215S

    5 Drive unit replacement ___________________________________________________________________________________________________________ 5.2.2 XY-215S Part list Required tools Item Part Name Service Part No. Note ・Phillips head Drive unit PT-XY215SL1 screwdriver M6 x 40mm (P=1.0) M6 socket head bolt 06G003 5mm hex socket head Spring washer 06D0075 Grille 04X903 Grille...
  • Page 67 5 Drive unit replacement ___________________________________________________________________________________________________________ Location of terminals Location of terminals (Right drive unit) (Left drive unit) Additional information (XY-215S) For the connection information, please refer to following circuit diagram.

  • Page 68: Specifications

    6 Specifications 6.1 Spec sheet XY-81 XY-101 XY-122 XY-152 Product Name XY-81-W XY-101-W XY-122-W XY-152-W Enclosure Type Two-way passive, reflex-loaded Two-way passive, reflex-loaded Two-way passive, reflex-loaded Two-way passive, reflex-loaded Frequency Response 75 Hz to 20 kHz 70 Hz to 20 kHz 70 Hz to 20 kHz 50 Hz to 20 kHz Sensitivity (1w/1m)
  • Page 69 6 Specifications 6.1 Spec sheet XY-115S XY-118S XY-215S XY-218S Product Name XY-115S-W XY-118S-W XY-215S-W XY-218S-W Enclosure Type Single driver, reflex-loaded subwoofer Single driver, reflex-loaded subwoofer Dual driver, quasi-bandpass subwoofer Dual driver, reflex-loaded subwoofer Frequency Response 45 Hz to 150 Hz 35 Hz to 150 Hz 42 Hz to 160 Hz 32 Hz to 150 Hz...

  • Page 70: Drawing

    6 Specifications 6.2 Drawing...
  • Page 71 6 Specifications 6.2 Drawing...
  • Page 72 6 Specifications 6.2 Drawing...
  • Page 73 6 Specifications 6.2 Drawing...
  • Page 74 6 Specifications 6.2 Drawing...
  • Page 75 6 Specifications 6.2 Drawing...
  • Page 76 6 Specifications 6.2 Drawing...
  • Page 77 6 Specifications 6.2 Drawing...

This manual is also suitable for:

Xy-81Xy-122Xy-152Xy-101Xy-115sXy-118s ... Show all

Table of Contents