Summary of Contents for Navmanu Qube 2
-
Page 1: Installation Manual
Qube 2 Installation Manual G P S T R A C K I N G A N D F L E E T M A N AG E M E N T S O L U T I O N S... -
Page 2: Table Of Contents
Installing the Qube 2 in a Vehicle ....... . . -
Page 3: Introduction
1.1 Important Notice It is the Owner’s sole responsibility to install and use the Qube 2 (the Product) in a manner that will not cause accidents, personal injury or property damage. For the purpose of this notice, “Owner”, “you” and “your” means the party (including any person authorised by that party to use and/or install the Product) that has either: (a) purchased the Product;... -
Page 4: Qube 2 Hardware
2 Qube 2 Hardware 2.1 Box Contents Vehicle connection cable Qube 2 unit with mounting rails Qube 2 Installation Manual G P S T R A C K I N G A N D F L E E T M A N AG E M E N T S O L U T I O N S Qube 2 Installation Manual.indd 1... -
Page 5: Quick Install - 4 Wire Basic Tracking
Display State Normal Operation Description Power Power ON, Unit awake Slow Flash Sleep mode No Power – Note: the Qube 2 should always be powered GPS fi x No GPS fi x CELL Data connection to cellular network No data connection... -
Page 6: Installing The Qube 2 In A Vehicle
IMPORTANT NOTICE • Before you begin, ensure that drilling will not damage the vehicle’s structure, wiring or equipment • Ensure the Qube 2 cables, mounting screws etc will pose no hazard to the occupants of the vehicle... -
Page 7: Antenna
They are mounted as far away as practical from any other antenna, to minimize the risk of interference • The cables can be easily routed to the Qube 2 • Antennas stuck to glass windows or the windscreen should be at least 13 mm (1⁄2”) from... -
Page 8: Wiring
Qube 2 | Installation Manual 5 Wiring Cable A Has a long cable with a RJ45 Plug, a short cable with a DB9 plug, and a single cable with bare ends for all other connections. Cable B (UK option) Has an RJ45 socket very close to the main plug (DB15), and a single long cable with bare ends for all other connections. -
Page 9: Connecting Auxiliary Devices
Qube 2 | Installation Manual 5.3 Connecting Auxiliary Devices The Qube 2 is equipped with additional IO that can be connected to auxiliary devices in the vehicle. These allow the Qube to generate events based on inputs from these devices. -
Page 10: Analogue Inputs
Connect the Orange wire directly to the positive of the backup battery, and ground the negative side of the battery at the same point as the Qube 2’s Black wire is grounded. If the Qube 2 is powered off 24V DC, then the Backup battery must also be 24V DC. If powered from 12V DC the Battery must be 12V DC. -
Page 11: Testing
Watching the meter, start the vehicle and ensure that the voltage does remain ON during starting If any of these tests fail, the Qube 2 is not connected to the correct signal. Please fi nd the correct wire. 6.2 Check Data and GPS... -
Page 12: Fault Finding
Check that the +12 / 24 V wire has permanent power connected to it Check the DB15 I/O connector is correctly connected, and the securing screws are hand tightened onto the Qube 2 GPS LED fails to light Ensure that the antenna is up the correct way, and has a clear view of as... -
Page 13: Specifi Cations
Qube 2 | Installation Manual 8 Specifi cations Dimensions: 19.0 15.0 Height = 42mm 13.5 56.0 98.5 Physical: Digital Inputs • Weight: 370g • Input Voltage LOW: < 1.0 V • Case Material: Aluminium Extrusion. • Input Voltage HIGH: > 4.0 V •... -
Page 14: Contacts And Legal
Qube 2 | Installation Manual 9 Contacts Navman Wireless Australia Pty Ltd Navman Wireless New Zealand Unit 3, 2-6 Chaplin Drive 7-11 Kawana Street, Northcote Lane Cove NSW 2066 PO Box 340-184, Birkenhead 0746 PO Box 3051, Monash Park NSW 2111... - Page 15 MN000032C Lat 42° 6’ 16.98” N Lon 87° 49’ 29.27” W...