Table of Contents
Advertisement
INST
INST
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
INST
INST
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOLT SYSTEM
W W W W W ARNING:
ARNING: If the information in these instructions is not followed exactly, a fire or
ARNING:
ARNING:
ARNING:
explosion may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
Installation and service must be performed by a qualified installer, service
Fax: (705)722-6031 Email: ask@napoleon.on.ca
Web: www.napoleon.on.ca
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS,
CSA 2.22, AND ANSI Z21.50 RESPECTIVELY FOR VENTED GAS FIREPLACES.
INSTALLA
INST
INST
ALLA
ALLATION AND OPERA
ALLA
TION AND OPERA
TION AND OPERATION INSTRUCTIONS FOR
TION AND OPERA
INST
INST
ALLA
TION AND OPERA
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
NATURAL GAS MODEL
PROPANE GAS MODEL
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / AGA / CGA METHODS
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
this or any other appliance.
WHA
WHA
WHA
WHA
WHAT T T T T T T T T TO DO IF YOU SMELL
O DO IF YOU SMELL GAS:
O DO IF YOU SMELL
O DO IF YOU SMELL
O DO IF YOU SMELL
agency or the gas supplier.
Wolf Steel Ltd., RR#1, 9 Napoleon Rd.,
Barrie, On., Canada L4M 4Y8 (705)721-1212
T SYSTEM
T SYSTEM
T SYSTEM
T SYSTEM
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
GD17 - N
GD17 - N
GD17 - N
GD17 - N
GD17 - N
GD17 - P
GD17 - P
GD17 - P
GD17 - P
GD17 - P
GAS:
GAS:
GAS:
GAS:
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
R-2000
WS-415-106 / 05.19.99
Advertisement
Table of Contents
Related Manuals for Napoleon GD17 - N
Summary of Contents for Napoleon GD17 - N
- Page 1 • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Wolf Steel Ltd., RR#1, 9 Napoleon Rd., Barrie, On., Canada L4M 4Y8 (705)721-1212 Fax: (705)722-6031 Email: ask@napoleon.on.ca R-2000 Web: www.napoleon.on.ca...
-
Page 2: Table Of Contents
T T T T T ABLE ABLE ABLE of of of of of CONTENTS ABLE CONTENTS CONTENTS CONTENTS ABLE CONTENTS PG 2-5 PG 2-5 INTRODUCTION INTRODUCTION OPTIONAL BLOWER INST OPTIONAL BLOWER INST ALLA ALLA TION TION PG 2-5 PG 2-5 PG 2-5INTRODUCTION INTRODUCTION INTRODUCTION... - Page 3 After the first year, NAPOLEON will not be responsible for installation, labour or any other costs or expenses related to the reinstallation of a warranted part, and such expenses are not covered by this warranty.
-
Page 4: General Instructions
Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean dry cloth. The glass is 3/16" tempered glass available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the first 10 hours of operation with a recommended gas fireplace glass cleaner. -
Page 5: Venting
Use the high temperature sealant provided. When using Napoleon venting components, use only the following vent kits: WALL TERMINAL KIT GD222, or 1/12 TO 7/12 PITCH ROOF TERMINAL KIT GD110, 8/12 TO 12/12 ROOF TERMINAL KIT GD111, FLAT ROOF TERMINAL KIT GD112 or PERISCOPE KIT GD201 (for wall penetration below grade) in conjunction with the various terminations, use either the 5 foot vent kit GD220 or the 10 foot vent kit GD330. - Page 6 Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. Only the following Napoleon Vent Kits, used in combination with each other may be used: A 1¼" air gap all around between the inner liner and outer liner is required for safe operation. Use a...
- Page 7 AIR TERMIN TERMIN TERMIN TERMINAL INST AL INST AL INST AL INSTALLA ALLA ALLA ALLATIONS: TIONS: TIONS: TIONS: TERMIN AL INST ALLA TIONS: FIGURE 6 INSTALLATIONS CANADIAN U.S.A. 12 INCHES 12 INCHES Clearance above grade, veranda porch, deck or balcony. 12 INCHES 9 INCHES Clearance to windows or doors that open.
-
Page 8: Inst
/ liner and the firestop spacer. VERTICAL INSTALLATION: This application occurs when venting through a roof. FIGURE 3. Installation kits for various roof pitches are available from your Napoleon dealer. See Accessories to order the specific kit required. 1. Determine the air terminal location, cut and frame 9½ inch openings in the ceiling and the roof to provide the minimum 1 inch clearance between the fireplace pipe / liner and any combustible material. -
Page 9: Using Flexible Vent Components
FIGURE 13. The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon support ring assembly GA-GD-010.370 or equivalent noncombustible strapping to main- tain the minimum 1" clearance to combustibles. -
Page 10: Fireplace Vent Connection
VERTICAL VENTING INST TICAL VENTING INST TICAL VENTING INST TICAL VENTING INSTALLA TICAL VENTING INST ALLA ALLA ALLA ALLATION TION TION TION TION FIGURE 14 1. Fasten the roof support to the roof using the screws FIGURE 15 provided. FIGURE 14. The roof support is optional. In this case the venting is to be adequately supported using ei- ther an alternate method suitable to the authority having jurisdiction or the optional roof support. -
Page 11: Using Rigid Vent Components
PER FOOT. The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon vent spacers WS-615-33 or equivalent every 3 feet and either side of each elbow to maintain the minimum 1¼" clearance between the outer and inner vent pipes. - Page 12 GAS INST GAS INST ALLA ALLA TION TION GAS INST GAS INST GAS INSTALLA ALLA ALLATION TION TION Proceed once the vent installation is complete. 1. Move the fireplace into position and secure using the nailing tabs (2 per side) and/or secure to the floor using #10 screws (not supplied).
-
Page 13: Framing
FRAMING FRAMING FRAMING FRAMING FRAMING It is best to frame your fireplace after it is positioned and the vent system is installed. Use 2x4's and frame to local building codes. FIGURE 22-24. FIGURE 24 FIGURE 23 FIGURE 22 To install the fireplace face flush with the finished wall, position the framework to accomodate the thickness of the finished wall. -
Page 14: Finishing
LOG PLACEMENT LOG PLACEMENT LOG PLACEMENT LOG PLACEMENT LOG PLACEMENT PHAZER logs exclusive to Napoleon Fireplaces, provide a unique and realistic glowing effect that is different in every installation. FIGURE 29a POSITIONING THE LOGS IMPROPERLY WILL CAUSE FLAME IMPINGEMENT AND CARBONING. -
Page 15: Optional Blower Installation
OPTIONAL BLOWER INSTALLATION INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE Canada or the ANSI/NFPA 70-1996 in the United States NATIONAL ELECTRICAL CODE If the fireplace was not previously equipped with a blower: route a... -
Page 16: Optional Fan Installation
This optional kit is meant to be used only in conjunction with the GD65 Fan BRACKET Kit, shown above, which may be ordered from your Wolf Steel / Napoleon dealer. With the thermostatic sensor option, the fan, when turned on, becomes... -
Page 17: Maintenance
6. Check to see that the main burner ignites completely on all openings when the gas knob for the burner is turned on. A 5 to 10 second total light-up period is satisfactory. If ignition takes longer, consult your Napoleon dealer / distributor. -
Page 18: Adjustments
ADJUSTMENTS FIGURE 41 THERMOPILE PILOT BURNER THERMO- COUPLE ELECTRODE PILOT BURNER ADJUSTMENT PILOT BURNER ADJUSTMENT PILOT BURNER ADJUSTMENT PILOT BURNER ADJUSTMENT PILOT BURNER ADJUSTMENT Adjust the pilot screw to provide properly sized flame. Turn in a clockwise direction to reduce the gas flow. FLAME MUST ENVELOP FIGURES 40 &... -
Page 19: Replacements
ORDERING REPLACEMENT P Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following information: 1. M &... -
Page 20: Vent Kits
VENT KITS VENT KITS VENT KITS VENT KITS VENT KITS GD220 (5 FT) GD220 (5 FT) GD220 (5 FT) GD220 (5 FT) GD220 (5 FT) PART NO. PART NO. PART NO. PART NO. PART NO. DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION GD-010.397 4"... -
Page 21: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE EFORE ATTEMPTING TO TROUBLESHOOT PURGE YOUR UNIT AND INITIALLY LIGHT THE PILOT AND THE MAIN BURNER WITH THE GLASS DOOR REMOVED SYMPTOM SYMPTOM SYMPTOM SYMPTOM SYMPTOM PROBLEM PROBLEM PROBLEM PROBLEM PROBLEM TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION Pilot... - Page 22 SYMPTOM SYMPTOM PROBLEM PROBLEM SYMPTOM SYMPTOM SYMPTOM PROBLEM PROBLEM PROBLEM TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION Main burner goes Refer to "MAIN BURNER GOES OUT; PILOT STAYS ON" out; pilot goes out. - check for vent blockage. Vent is blocked - check joint seals and installation.
- Page 23 NOTES: WS-415-106 /05.19.99...