Miele KM 360 Installation Instructions Manual
Gas-hobs
Hide thumbs
Also See for KM 360:
- Installation instructions manual (28 pages) ,
- Operating instructions manual (28 pages) ,
- Specifications (7 pages)
Table of Contents
Related Manuals for Miele KM 360
Summary of Contents for Miele KM 360
-
Page 1: Installation Instructions
Installation instructions Gas-hobs KM 360 / KM 360-1 KM 361 KM 362 / KM 362-1 KM 363 To avoid the risk of accident or damage to the appliance it is essential to read these instructions before installing or using it. - Page 2 Per questo se si vuole usare l'apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.
-
Page 3: Table Of Contents
KM 360-1 / KM 362-1 ........ -
Page 4: Warning And Safety Instructions
Warning and Safety instructions Building in Fit wall units and the cooker hood before fitting the appliance, to avoid damaging it. The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat resistant adhesive which will not dissolve or distort. - Page 5 The hob may be installed above a A minimum safety distance b must be Miele oven, if the work-top is at maintained between the hob and the least 40 mm thick. cooker hood above it. See the The gas hob must not be installed manufacturer’s operating and...
-
Page 6: Appliance Dimensions And Worktop Cut-Out
Appliance dimensions and worktop cut-out KM 360 / KM 362... - Page 7 Appliance dimensions and worktop cut-out a Building-in height b Connection box c Gas connection R - ISO 7-1 (DIN2999) ^ Make the worktop cut-out following the dimensions shown above. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 100 mm to the right or left of the hob.
- Page 8 Appliance dimensions and worktop cut-out KM 360-1 / KM 362-1...
- Page 9 Appliance dimensions and worktop cut-out a Building-in height b Connection box c Gas connection R - ISO 7-1 (DIN2999) ^ Make the worktop cut-out following the dimensions shown above. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 100 mm to the right or left of the hob.
- Page 10 Appliance dimensions and worktop cut-out KM 361 / KM 363...
- Page 11 Appliance dimensions and worktop cut-out a Building-in height b Connection box c Gas connection R - ISO 7-1 (DIN2999) ^ Make the worktop cut-out following the dimensions shown above. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 100 mm to the right or left of the hob.
-
Page 12: Safety Clearance
Safety clearance Before installing the appliance check that the location provides the required clearances from combustible materials and if necessary provide protection to adjacent surfaces as required by regulations. Shown area indicates protected surface, which may be ceramic tiles or other approved material. - Page 13 Safety clearance Clearance above and around the appliance a Range hood b not less than 650 mm from burner to any horizontal surface over full width of the appliance. c Burner d 10 mm recommended minimum e Combustible work bench f Regulator (NG) g test nipple of regulator 7 mm diam.
-
Page 14: Installation
Installation Building in Fixing the support brackets ^ Place the hob in the prepared cut-out. ^ Feed the electrical connection cable through the cut-out and connect. ^ Make the gas connection (see relevant section). ^ Secure the gas hob in position with fixing brackets a supplied as shown. - Page 15 Installation Under no circumstances should sealant find its way between the frame of the top part of the hob and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing, (possibly leading to damage to the frame and worktop).
-
Page 16: Electrical Connection
Electrical connection Important All electrical work should be carried The wires in the mains lead are out by a suitably qualified and coloured in accordance with the competent person in strict following code: accordance with national and local safety regulations. Green/yellow = earth Blue = neutral... -
Page 17: Gas Connection
Gas connection Depending on country of destination Connection to the gas supply, or this appliance is set up for connection conversion from one type of gas to to natural or liquid gas. another should only be undertaken See adhesive label on the appliance: by an approved fitter, who is G = NG (natural gas) responsible for correct functioning of... - Page 18 Gas connection Gas pressure must be set by the The gas connection must be in approved gas fitter as shown on the accordance with national and local data plate: regulations. Natural gas 1.0 kPa The relevant building regulations must also be observed. ULPG (Propane/Butane) 2.75 kPa ^ Disconnect gauge and screw in the...
-
Page 19: Nominal Rating Table
Nominal Rating Table Nominal rating for all gas types with the burner full on Burner KM 360 / KM 360-1/ KM 362 / KM 362-1 KM 363 type KM 361 MJ/h MJ/h MJ/h Auxiliary 3.85 3.85 3.85 burner ULPG 3.60 3.60... -
Page 20: Conversion To Another Type Of Gas
Conversion to another type of gas Jet table When converting to liquid gas, the main jets and the small jets of all burners must be changed. Screw in the new jets according to the following table. Main jet Ø Low setting jet Ø Auxiliary burner 0.90 0.42... -
Page 21: Changing The Jets
Conversion to another type of gas Changing the jets Changing the main jets Disconnect the gas hob from the Auxiliary-, Normal and Fast burner electricity supply. Depending on the type of installation, either withdraw the mains fuse, switch off at the fused spur unit, or at the socket and withdraw the plug. - Page 22 Conversion to another type of gas Wok burner ^ Take off the burner cover a, burner ring b and burner head c. ^ Loosen the screws d and take off the plate. ^ Using an (M7) socket spanner unscrew the main jets e (larger diameter) and f (smaller diameter).
-
Page 23: Changing The Low Setting Jets
Conversion to another type of gas Changing the low setting jets (all burners) To change the low setting jets the fastening screws of the burners must be loosend and the upper part of the appliance has to be taken off. ^ Pull off the control knobs. -
Page 24: After Conversion
The flame must not go out in the lowest place. setting, nor when the control is turned quickly from a high to a low setting. KM 360 G / KM 362 G When replacing the stainless steel In the highest setting the flame must upper section: have a distinctive and visible core. - Page 28 Alteration rights reserved / 1605 M.-Nr. 05 827 671 / 01 en - AUS...