Panasonic SH-FX65P Service Manual
Panasonic SH-FX65P Service Manual

Panasonic SH-FX65P Service Manual

Wireless system and digital transmitter
Table of Contents

Advertisement

Specification
n RF SECTION
Wireless module
Frequency range
Number of channels
n AMPLIFIER SECTION
Output power
RMS output power
Surround Ch
Total RMS power
FTC output power
Surround Ch
Total FTC power
n GENERAL
Power supply
Power consumption
SH-FX65T
SE-FX65
Wireless System and Digital Transmitter
2.400 to 2.4835 GHz
125 W per channel (3Ω), 1 kHz, 10
% THD
250 W
34 W per channel (3Ω), 120 Hz-20
kHz, 1 % THD
68 W
AC 120 V, 60Hz
1.5 W
35 W
SH-FX65P
SH-FX65PC
SE-FX65P
SE-FX65PC
SH-FX65TPP
Colour
(S)..........Silver Type
(K)..........Black Type (For SC-PT750P/PC-K)
(K2)..........Black Type (For SC-PT950P/PC-K)
Dimensions (W x H x D)
SH-FX65T
SE-FX65
3
Mass
SH-FX65T
SE-FX65
Operating temperature range
Operating humidity range
Power consumption in off mode
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate
2. Total harmonic distortion is measured by a digital spectrum
analyzer
Power supply:
This model uses Switching Mode Power Supply (SMPS) Module for
powering the receiver unit. It is replaceable as an assembly unit.
© 2007 Matsushita Electric Industrial Co. Ltd.. All
rights
distribution is a violation of law.
ORDER NO. MD0702020CE
65 mm x 52 mm x 8.6 mm
(2-9/16" x 2-1/16" x 11/32")
165 mm x 90 mm x 164 mm
(6-1/2" x 3-17/32" x 6-15/32")
0.02 kg (0.04 lbs)
0.655 kg (1.54 lbs)
+5 °C to +35 °C (+41 °F to +95 °F)
5 % to 90 % RH (no condensation)
approx. 0.2 W
reserved.
Unauthorized
copying
A6
and

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic SH-FX65P

  • Page 1 ORDER NO. MD0702020CE Wireless System and Digital Transmitter SH-FX65P SH-FX65PC SE-FX65P SE-FX65PC SH-FX65TPP Colour (S)..Silver Type (K)..Black Type (For SC-PT750P/PC-K) (K2)..Black Type (For SC-PT950P/PC-K) Specification n RF SECTION Dimensions (W x H x D) Wireless module SH-FX65T 65 mm x 52 mm x 8.6 mm (2-9/16”...
  • Page 2: Table Of Contents

    SH-FX65P / SH-FX65PC CONTENTS Page Page 1 Note 11.1. Checking of Led, Led Drive, DAMP and Receiver Module 1.1. System Combination Breakdown P.C.B. 1.2. Packaging 12 Voltage Measurement & Waveform Chart 2 Safety Precautions 12.1. Voltage Measurement 2.1. GENERAL GUIDELINES 12.2.
  • Page 3: Note

    SH-FX65P / SH-FX65PC 1 Note 1.1. System Combination Breakdown Note: The diagrams below show the breakdown for the digital transmitter and wireless system. For SH-FX65P/PC-S Digital Tx & Rx System SH-FX65P/PC-S Wireless Transmitter SH-FX65TPP-S Wireless Receiver SE-FX65P/PC-S For SC-PT750P/PC-K Digital Tx & Rx System...
  • Page 4: Safety Precautions

    SH-FX65P / SH-FX65PC 2 Safety Precautions 2.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
  • Page 5: Protection Circuitry

    SH-FX65P / SH-FX65PC 2.3. Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: · No sound is heard when the power is turned on. · Stops during a performance. The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
  • Page 6: Prevention Of Electro Static Discharge (Esd) To

    SH-FX65P / SH-FX65PC 3 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip”...
  • Page 7: Handling The Lead-Free Solder

    SH-FX65P / SH-FX65PC 4 Handling the Lead-free Solder 4.1. Service caution based on legal restrictions 4.1.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
  • Page 8: Accessories

    SH-FX65P / SH-FX65PC 5 Accessories Note : Refer to Packing Materials & Accessories Parts List (Section 22) for the part number. AC Power Cord...
  • Page 9: Using Of Digital Receiver Unit

    SH-FX65P / SH-FX65PC 6 Using of Digital Receiver Unit 6.1. Connecting the digital transmitter (SH-FX65T) 6.2. Connecting the surround speaker cables to the wireless system (SE- FX65) 6.3. AC Power Cord connection (SE-FX65)
  • Page 10: Making The Wireless Link (Se-Fx65)

    SH-FX65P / SH-FX65PC 6.4. Making the wireless link (SE-FX65)
  • Page 11: Operation Procedures

    MUTING flashes in the main unit s display while the For details, refer to the operating instructions for the function is on. optional Panasonic wireless sound system SH-FX85. To cancel, press the button again or adjust the volume. Muting is canceled when you switch the unit to standby.
  • Page 12: Main Unit Key Buttons Operations

    SH-FX65P / SH-FX65PC 7.2. Main Unit Key Buttons Operations Standby/on switch [POWER OPEN/CLOSE / -TUNE MODE / FM MODE Turn the main unit on/off. Open/Close the disc drawer Stop playing/ Press to switch the unit from on to Select the tuning mode standby mode or vice versa.
  • Page 13: New Features

    SH-FX65P / SH-FX65PC 8 New Features 8.1. Wireless Features 8.1.1. Function Overview Year 2007 PT models support wireless which includes FX65/FX66, wireless subwoofer and FX85 as described below:- 8.1.1.1. FX65/FX66 · The FX65/FX66 supports one-way wireless transmission only, that is, it will only transmit wireless audio signal to the rear surround speakers.
  • Page 14 SH-FX65P / SH-FX65PC 8.1.2.1. TX-TYPE A / RX-TYPE 1 Note: - One way only FX65/FX66 signal flow - FX65/FX66 only Type A Type 1 · Type A transmitter uses one ADC (Analog to Digital Converter) and transmits audio through Channel 2. Type 1 receiver (Rx) uses one DAC and output audio through Channel 2.
  • Page 15: Led Indication

    SH-FX65P / SH-FX65PC 8.1.2.2. TX-TYPE B / RX-TYPE 2 Note: FX65/FX66 SIGNAL FLOW - FX85 S S IGNAL F F LOW - ONE WAY AND SIMULTANEOUS - FX65/FX66 + FX85 - FX65/FX66 TRANSMITTER NOT USED, NEED TO IDSET FX65/FX66 - TX TYPE B BUT RX...
  • Page 16 SH-FX65P / SH-FX65PC · Stop Button This button will send command to the main unit to stop CD/DVD as well as the iPod. This function is therefore meaningful only if the second room selector is in Main Source (if the first room user is in CD/DVD mode or iPod) and iPod.
  • Page 17 SH-FX65P / SH-FX65PC CH2/AB FX65/FX66 Case 2 A: FX65/FX66 + FX85 · In this configuration, a second receiver, an FX85, in another room is listening to another audio source from the main set. The FX85 also is able to send command to the main set such as Play, Stop, Skip, and Preset Tuner Channel Up/Down. This configuration uses Type B transmitter which is an upgrade of the Type A and can be used on Type 1 (FX65/FX66).
  • Page 18 SH-FX65P / SH-FX65PC CH2/AB CH2/AB Case 3 B: FX65/FX66 + FX85 + Wireless Subwoofer (for PTX7, PT1050) · In this configuration, all audio source for the Type 1 subwoofer and Type 1 first room receiver (FX65/FX66) through streams AB via Ch 2 and Type 2 second room receiver (FX85) comes from transmitter B through streams CD via Ch 1. For this configuration, the user must perform ID setting for FX85 if it is sold as an accessory, but for bundled type, it already is paired with the transmitter.
  • Page 19 SH-FX65P / SH-FX65PC 8.1.7. User Operation Flow START Is Tx card inserted? Insert Tx card POWER ON MAINSET Is there audio source playing? Play music Is music heard on CHECK FOR SPEAKER Is wireless link led wireless surround WIRE CONNECTIONS...
  • Page 20: Self-Diagnosis And Special Mode Setting

    SH-FX65P / SH-FX65PC 9 Self-Diagnosis and Special Mode Setting 9.1. Wireless Service Mode Summary Table The service modes can be activated by pressing various button combination on the player and remote control unit. Below is the summary of major checking:...
  • Page 21: Service Mode Table (Wireless)

    SH-FX65P / SH-FX65PC 9.2. Service Mode Table (Wireless) By pressing various button combinations on the player and remote control unit, you can activate the various service modes for checking. 9.2.1. Service Mode Table 1 Item Key Operation FL Display Mode Name...
  • Page 22 SH-FX65P / SH-FX65PC 9.2.2. Service Mode Table 2 Item Key Operation FL Display Mode Name Description Front Key (Display 1) RF Channel RF Channel 1 Display* Main room is in AUX mode. Selection Display FL Display sequence: Display 1 (Display 2)
  • Page 23: Assembling And Disassembling

    SH-FX65P / SH-FX65PC 10 Assembling and Disassembling 10.1. Note “ATTENTION SERVICER” Some chassis components may be have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
  • Page 24: Disassembly Flow Chart (For Se-Fx65)

    SH-FX65P / SH-FX65PC 10.2. Disassembly flow chart (For SE-FX65) The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. For the digital receiver unit only. To assemble the unit, reverse the steps shown in the chart below.
  • Page 25: Disassembly Of Wireless System (Se-Fx65P/Pc)

    SH-FX65P / SH-FX65PC 10.4. Disassembly of Wireless System (SE-FX65P/PC) 10.4.1. Disassembly of Top Panel Step 1 : Remove 2 screws. Step 3 : Lift up the top panel. Step 4 : Detach connector (CN1003). Step 5 : Push back slightly before lifting the top panel from the unit.
  • Page 26 SH-FX65P / SH-FX65PC 10.4.2. Disassembly of Led P.C.B and Led Drive P.C.B · Follow the (Step 1) - (Step 5) of item 10.4.1. Step 1 : Remove 1 screw. Step 2 : Release the catches. Caution : Don’t apply too much force in releasing the Step 3 : Remove SMPS Module Unit as arrow shown.
  • Page 27 SH-FX65P / SH-FX65PC Step 2 : De-solder to remove IC5200. Step 2 : Remove 3 screws. Step 3 : Remove DAMP P.C.B as arrow shown. 10.4.5. Replacement of Digital Amp IC · Follow the (Step 1) - (Step 5) of item 10.4.1.
  • Page 28: Disassembly Of Transmitter Module P.c.b (Sh-Fx65T)

    SH-FX65P / SH-FX65PC Step 1 : Remove 4 screws. Step 2 : Remove Receiver Module P.C.B as arrow shown. · Assembly of Receiver Module P.C.B Step 2 : Remove bottom casing as arrow shown. Step 1 : Insert the Receiver Module P.C.B until it is completely secured.
  • Page 29: Service Positions

    SH-FX65P / SH-FX65PC 11 Service Positions Note: For description of the disassembly procedures, see the Section 10. 11.1. Checking of Led, Led Drive, DAMP and Receiver Module P.C.B.
  • Page 30: Voltage Measurement & Waveform Chart

    SH-FX65P / SH-FX65PC 12 Voltage Measurement & Waveform Chart Note: · Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
  • Page 31: Waveform Chart

    SH-FX65P / SH-FX65PC 12.2. Waveform Chart RF TEST POINT PLAY...
  • Page 32: Wiring Connection Diagram

    SH-FX65P / SH-FX65PC 13 Wiring Connection Diagram CN1000 DAMP P.C.B SPEAKER JK1000 TO SMPS MODULE UNIT 7 ..1 H1001 LED P.C.B LED DRIVE P.C.B CN4000 H4003 3 2 1 H4000 5 . . . 1 TRANSMITTER MODULE P.C.B...
  • Page 33: Block Diagram

    SH-FX65P / SH-FX65PC 14 Block Diagram 14.1. DIGITAL AMPLIFIER/LED DRIVE/LED BLOCK DIAGRAM -VCC -VCC +VCC +VCC...
  • Page 34: Receiver Module Block Diagram

    SH-FX65P / SH-FX65PC 14.2. RECEIVER MODULE BLOCK DIAGRAM...
  • Page 35: Transmitter Module Block Diagram

    SH-FX65P / SH-FX65PC 14.3. TRANSMITTER MODULE BLOCK DIAGRAM...
  • Page 36 SH-FX65P / SH-FX65PC...
  • Page 37: Notes Of Schematic Diagram

    SH-FX65P / SH-FX65PC 15 Notes of Schematic Diagram (All schematic diagrams may be modified at any time with the development of new technology) Notes: S1000: ID SET switch. S1001: POWER switch. · Importance safety notice : Components identified mark have special characteristics important for safety.
  • Page 38 SH-FX65P / SH-FX65PC...
  • Page 39: Schematic Diagram

    SH-FX65P / SH-FX65PC 16 Schematic Diagram 16.1. DAMP CIRCUIT, LED DRIVE CIRCUIT and LED CIRCUIT SCHEMATIC DIAGRAM - 1 LED DRIVE CIRCUIT DAMP CIRCUIT : + B SIGNAL LINE : - B SIGNAL LINE : MAIN SIGNAL LINE H4000 Z1000...
  • Page 40 SH-FX65P / SH-FX65PC SCHEMATIC DIAGRAM - 2 DAMP CIRCUIT : + B SIGNAL LINE : + B SIGNAL LINE : MAIN SIGNAL LINE Q1004 B1ADCE000012 BIAS SWITCH R1007 R1008 1.2K 1.2K R1009 4.7K Q1005 IC5200 Q1005 B1GBCFJJ0051 C1BA00000487 Q1006 DIGITAL HIC (CLASS-D AMP)
  • Page 41: Receiver Module Circuit

    3.3V REGULATOR 4.7u P1.7 R1014 VOUT P6.0 P3.0 0.1u 0.1u R1022 6.3V100 P6.1 P3.1 R1017 P3.3 P3.2 R1116 L1101 GNDE 3.3V C1506 C1503 1.8K 1.8K 1.8K 1.8K TO RECEIVER MODULE SECTION (3/4) STATIC SENSITIVE PART SH-FX65P/PC (SE-FX65P/PC) RECEIVER MODULE CIRCUIT...
  • Page 42 R1407 IC1105 C1BB00001071 POWER ON RESET IC R1101 VOUT TP23 C1101 0.047u TP22 IC1101 EEPROM IC (NOT SUPPLIED) R1102 R1103 C1103 C1102 0.1u 0.047u R1104 R1105 3.3V TO RECEIVER MODULE SECTION (4/4) STATIC SENSITIVE PART SH-FX65P/PC (SE-FX65P/PC) RECEIVER MODULE CIRCUIT...
  • Page 43 0.1u 10V10u 0.56p 0.1u 0.56p ANT2+ XTAL G1C2N7ZA0068 G1C3N9ZA0068 F1G1HR56A561 ANT2- VCC_XTAL PCB ANT GND_CP 0.01u G1C3N9ZA0068 0.56p /SHDN VCC_CP 0.01u 0.01u C1509 C1508 100p 100p 0.1u G1C47NJA0048 0.01u 0.01u 6.3V1100 C1507 STATIC SENSITIVE PART SH-FX65P/PC (SE-FX65P/PC) RECEIVER MODULE CIRCUIT...
  • Page 44 R1505 DIN_B B6_RX_ANT_A_EN R1506 IC10 AUDIOCLK J0JCC0000278 AUDIO_CLK_OUT GND_IO C1AB00002772 BASE BAND IC B6_RX_ANT_B_EN R1507 B3_AGC_RESET AGND_IO VCC_3_IO VCC_3_IO SHDN B5_MODE_PA GPIO_2 / INT SPI_EN ASIC_RESET_(N) GPIO_RESN SPI_CLK FRAME_CLK DEBUG_TXD CONNECT H0J122500037 STATIC SENSITIVE PART SH-FX65P/PC (SE-FX65P/PC) RECEIVER MODULE CIRCUIT...
  • Page 45: Transmitter Module Circuit

    3.3V REGULATOR 4.7u P1.7 R1014 VOUT P6.0 P3.0 0.1u 6.3V220 R1022 6.3V100 0.1u P6.1 P3.1 R1017 P3.3 P3.2 L1101 GNDE +3.3V C1506 C1503 C1512 1.8K 1.8K 1.8K 1.8K TO TRANSMITTER MODULE SECTION (3/4) STATIC SENSITIVE PART SH-FX65P/PC (SH-FX65TPP) TRANSMITTER MODULE CIRCUIT...
  • Page 46 D1101 C1101 B0JCAE000001 TP22 IC1101 R1108 EEPROM IC NOT SUPPLIED R1102 D1102 B0JCAE000001 R1103 C1103 C1102 0.1u 0.047u R1104 R1105 R1110 R1111 Q1101 B1GBCFJJ0051 LEVEL SHIFTER +3.3V TO TRANSMITTER MODULE SECTION (4/4) STATIC SENSITIVE PART SH-FX65P/PC (SH-FX65TPP) TRANSMITTER MODULE CIRCUIT...
  • Page 47 10V10 0.56p 0.1u 0.56p ANT2+ XTAL G1C2N7ZA0068 ANT2- VCC_XTAL PCB ANT G1C3N9ZA0068 F1G1HR56A561 GND_CP 0.01u /SHDN VCC_CP G1C3N9ZA0068 0.56p C1513 0.01u 0.01u C1509 C1508 100p 100p 0.1u G1C47NJA0048 0.01u 0.01u 6.3V100 C1507 STATIC SENSITIVE PART SH-FX65P/PC (SH-FX65TPP) TRANSMITTER MODULE CIRCUIT...
  • Page 48 DIN_B B6_RX_ANT_A_EN R1506 IC10 AUDIOCLK J0JCC0000278 AUDIO_CLK_OUT GND_IO C1AB00002772 BASE BAND IC B6_RX_ANT_B_EN R1507 A1_TM_SEL0 B3_AGC_RESET AGND_IO VCC_3_IO VCC_3_IO SHDN B5_MODE_PA GPIO_2 / INT SPI_EN ASIC_RESET_(N) GPIO_RESN SPI_CLK FRAME_CLK DEBUG_TXD CONNECT H0J122500037 STATIC SENSITIVE PART SH-FX65P/PC (SH-FX65TPP) TRANSMITTER MODULE CIRCUIT...
  • Page 49: Printed Circuit Board Diagram

    SH-FX65P / SH-FX65PC 17 Printed Circuit Board Diagram 17.1. DAMP P.C.B, LED DRIVE P.C.B, LED P.C.B and RECEIVER MODULE P.C.B RECEIVER MODULE P.C.B (REPX0583A) DAMP P.C.B (REPX0584A) IC3002 W1027 R3202 W1003 IC3001 W1032 W1026 C2014 C3204 R1010 IC1102 R3207 Q1007...
  • Page 50: Transmitter Module P.c.b

    SH-FX65P / SH-FX65PC 17.2. TRANSMITTER MODULE P.C.B TRANSMITTER MODULE P.C.B (REPX0582A) IC1102 (PATTERN CONNECTOR) IC13 1 3 4 (PATTERN CONNECTOR) C1306 C1308 C1305 C1307 R1500 R1501 R1502 IC1300 R1503 R1504 R1505 IC10 R1506 R1507 30 32 L1101 (PATTERN CONNECTOR) Q1101...
  • Page 51: Illustration Of Ic's, Transistors And Diodes

    SH-FX65P / SH-FX65PC 18 Illustration of IC's, Transistors and Diodes C1BA00000487 C0FBAK000019 C2BBED000056 (30P) C1BB00001071 C0DBZGC00067 C0ABBB000067 C0FBBK000066 C0CBCBC00090 C3EBDC000070 (8P) C0DBZYY00262 No.1 B1ACCF000094 B1ADCE000012 B1ACKD000006 C1AB00002772 (64P) C1CB00002648 (48P) C1CB00001841 (12P) B1GBCFJJ0051 B1AAKD000012 B1ABCF000176 B1GDCFJJ0047 B0JCAE000001 B3AGA0000122 B0ECKP000002 B0BC01600013...
  • Page 52: Terminal Functions Of Integrated Circuits

    SH-FX65P / SH-FX65PC 19 Terminal Functions of Integrated Circuits 19.1. IC10 (C1AB00002772): IC Terminal Name Function BASE BAND TX_DATA_ BB I channel transmit data I_NOT (complement) Terminal Name Function TX_DATA_Q BB Q channel transmit data TX_DATA_ BB Q channel transmit data...
  • Page 53: Ic1000 (C2Bbed000056): Ic Mcu

    SH-FX65P / SH-FX65PC Terminal Name Function Terminal Name Function CP_OUT PLL charge pump output. P3.1 Connection for on-chip debug mode setting pins VCC_CP Supply voltage for PLL charge pump. P3.0 External interrupt request input GND_CP Charge pump circuit ground connection P1.7...
  • Page 54 SH-FX65P / SH-FX65PC...
  • Page 55: Exploded Views

    SH-FX65P / SH-FX65PC 20 Exploded Views 20.1. Cabinet Parts Location...
  • Page 56: Packaging

    SH-FX65P / SH-FX65PC 20.2. Packaging 20.2.1. Packaging Condition For SH-FX65P/PC-S...
  • Page 57 SH-FX65P / SH-FX65PC 20.2.2. Packaging Condition For SH-PT950P/PC-K Pls refer to section 1.2 for notes on packaging...
  • Page 58 SH-FX65P / SH-FX65PC 20.2.3. Packaging Condition For SH-PT750P/PC-K Pls refer to section 1.2 for notes on packaging...
  • Page 59: Service Hint

    SH-FX65P / SH-FX65PC 21 Service Hint The following kit assembly is for purpose for parts replacement:- Models Part No. Part Name & Description Remarks SH-PT750P/PC-K / SH-PT950P/PC-K RFKVEFX65P-K TX / RX KIT ASSEMBLY (K) [M] (RTL) SH-FX65P/PC-S RFKVEFX65P-S TX / RX KIT ASSEMBLY (S)
  • Page 60: Replacement Parts List

    Persian Ukraine Caution: 1. This parts list does not include parts for SMPS module. *1 represents for model SH-FX65P-S only *2 represents for model SH-FX65PC-S only *3 represents for model SH-PT750P/PC-K only *4 represents for model SH-PT950P/PC-K only * For reference only Ref.
  • Page 61 SH-FX65P / SH-FX65PC Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks IC13 C1CB00002648 IC RF [M] * IC1000 C2BBED000056 IC MCU JACKS IC1102 C0CBCBC00090 IC 3.3V REGULATOR IC1103 C0CBCBC00090 IC 3.3V REGULATOR...
  • Page 62 SH-FX65P / SH-FX65PC Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R1007 ERJ3GEYJ122V 1.2K 1/16W R3113 ERJ3GEY0R00V 0 1/16W R1008 ERJ3GEYJ122V 1.2K 1/16W R3114 ERJ3GEY0R00V 0 1/16W R1009 ERJ2GE0R00X 0 1/32W R3201...
  • Page 63: Parts List (Sh-Fx65T)

    SH-FX65P / SH-FX65PC Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ECJ0EC1H100D 10P 50V [M] * C2010 ECA1EAM101XB 100 25V ECJ0EC1H100D 10P 50V [M] * C2011 ECJ1VB1H104K 0.1 50V ECJ0EC1H330J 33P 50V...
  • Page 64 SH-FX65P / SH-FX65PC Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks IC1300 C0FBAK000019 IC AUDIO ADC R1021 ERJ2GE0R00X 0 1/32W R1022 ERJ2GEJ331X 330 1/32W TRANSISTORS R1027 ERJ2GEJ103X 10K 1/32W R1101...
  • Page 65 SH-FX65P / SH-FX65PC Ref. No. Part No. Part Name & Description Remarks ECJ0EC1H100D 10P 50V [M] * ECJ0EC1H220J 22P 50V [M] * ECJ0EC1H330J 33P 50V [M] * ECJ0EC1H330J 33P 50V [M] * ECJ0EC1H470J 47P 50V [M] * ECJ0EF1C104Z 0.1 16V...

This manual is also suitable for:

Se-fx65pSh-fx65pcSe-fx65pcSh-fx65tpp

Table of Contents