Immediately before handling any been brought into compliance. semiconductor components or assemblies, drain the electrostatic charge from your SAMSUNG ELECTRONICS ITALY S.P.A body by touching a known earth ground. VIA F.LLI GRACCHI,48 20092-CINISELLO BALSAMO MILAN 16. Always connect a test instrument's ground...
Page 3
(Use a screwdriver.) 3. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. Fig. 1-1. Discharging the High Voltage Capacitor Samsung Electronics...
2. Specifications 2-1 Table of Specifications TIMER 99 MINUTES 90 SECONDS POWER LEVEL ON TIME OFF TIME POWER SOURCE 230V 50Hz, AC M757 POWER CONSUMPTION MICROWAVE : 1,300W 4 sec 26 sec 160W 7 sec 23 sec OUTPUT POWER FROM 80 TO 800W (10 LEVEL POWER)
4-1 Replacement of High Voltage Transformer 1. Discharge the high voltage capacitor. 2. Disconnect all the leads. 3. Remove the mounting bolts. 4. Reconnect the leads correctly and firmly. Screws H. V. Trans Samsung Electronics...
1. Insertion depth of the thin metal plate should be 0.5mm or less. 4-3-4 Removal of Key Door & Spring Door "E" Remove pin hinge from Door "E" Detach spring from Door "E" and key door. Key Door Spring Samsung Electronics...
Base Plate Drive Motor Cover 8. Connect all the leads to the drive motor. 9. Screw the deive motor cover to the base plate with a screw driver. 10. Remount the coupler in the correct position. Samsung Electronics...
Page 9
2. Disconnect the connectors from the control circuit board. 3. Remove screws securing the control circuit bord. 4. Lift up the control circuit board from right side and remove the hooks holding the contol circuit board to the box assembly. SCREWS Samsung Electronics...
3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the high voltage capacitor. 5-1 High Voltage Transformer 1. Remove connectors from the transformer terminals Filament Terminals and check continuity. 2. Normal resistance readings are as follows: MODEL M757 Secondary Approx. 130W Filament Approx.0W Primary Approx.1.700W...
Door Closed 5. Confirm that the gap between the switch ¥ Primary switch housing and the switch actuator is no more than ¥ Monitor switch (COM-NC) 0.5mm when door is closed. ¥ Monitor switch (COM-NO) ¥ Door Sensing S/W Samsung Electronics...
Page 12
5. After heating for 2 minutes, measure the water temperature in each beaker. 6. Microwave heat distribution rate can be calculated as follows: Minimum Beaker Temperature Rise Heat Distribution = X 100(%) Maximum Temperature Rise The result should exceed 65%. Cooking Tray Samsung Electronics...
2) If the radiation leakage is more than 4 mW/ß≤ after determining that all parts are in good condition, functioning properly and the identical parts are replaced as listed in this manual notift that fact to ; SAMSUNG ELECTRONICS ITALY S.P.A VIA F.LLI GRACCHI,48...
H.V.Transformer component test procedure and replace if it is H.V.Capacitor defective. H.V.Diode, H.V.Fuse Magnetron 4. Open or loose wiring of power relay 5. Defective primary latch switch 6. Defective power relay or Ass'y PCB Replace PCB main. Samsung Electronics...
Page 15
Use plastic wrap or cover with a lid. Stir once or twice while cooking foods such as soup, cocoa, or milk. Noise from the turntable motor Noise may result from the motor. Replace turntable motor. when it starts to operate. Samsung Electronics...
: P.C.B IN/OUT ORANGE POINT ASSY MAIN P.C.B WHITE BLACK YELLOW MONITOR PRIMARY DOOR GREEN SWITCH LATCH SENSING YELLOW/GREEN SWITCH SWITCH MAGNETRON HIGH VOLTAGE DIODE TO CHASSIS HIGH VOLTAGE CAPACITOR H.V.FUSE SYMBOL COLOR ORANGE BROWN BLUE HIGH VOLTAGE TRANSFORMER Samsung Electronics...