Page 1 ThinkServer TD100 and TD100x Types 6398, 6399, 6419, 6429, 4203, 4204, 4205, and 4206 Hardware Maintenance Manual...
Page 3 ThinkServer TD100 and TD100x Types 6398, 6399, 6419, 6429, 4203, 4204, 4205, and 4206 Hardware Maintenance Manual...
Page 4 Portions © Copyright International Business Machines Corporation 2008. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Page 5: Table Of Contents
Configuring the Ethernet controller....23 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 ......25 Replaceable server components .
Page 6 Removing the hot-swap power-supply cage assembly ..125 Installing the hot-swap power-supply cage assembly Removing the simple-swap backplate (TD100 - some models) ..128 Installing the simple-swap backplate (TD100 - some models) ..130 Removing the SAS/SATA backplane Installing the SAS/SATA backplane .
Page 7 Solving undetermined problems ....215 Calling Lenovo for service ....216 Getting help and technical assistance .
Page 8 Korean Class A warning statement ....228 Index ......229 ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 9: Safety
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet. Antes de instalar este produto, leia as Informações sobre Segurança. Antes de instalar este producto, lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här produkten. © Lenovo 2008. Portions © IBM Corp. 2008.
Page 10: Guidelines For Trained Service Technicians
Use the information in this section to help you identify potential unsafe conditions in ® an IBM product that you are working on. Each Lenovo product, as it was designed and manufactured, has required safety items to protect users and service technicians from injury. The information in this section addresses only those items.
Page 11: Guidelines For Servicing Electrical Equipment
Guidelines for servicing electrical equipment Observe the following guidelines when servicing electrical equipment: v Check the area for electrical hazards such as moist floors, nongrounded power extension cords, power surges, and missing safety grounds. v Use only approved tools and test equipment. Some hand tools have handles that are covered with a soft material that does not provide insulation from live electrical currents.
Page 12: Safety Statements
Be sure to read all caution and danger statements in this documentation before performing the instructions. Read any additional safety information that comes with your server or optional device before you install the device. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 13 Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet.
Page 14 Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 15 Statement 4: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device.
Page 16 If you suspect a problem with one of these parts, contact a service technician. Statement 10: CAUTION: Do not place any object weighing more than 82 kg (180 lb) on top of rack-mounted devices. >82 kg (180 lb) ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 17 Statement 11: CAUTION: The following label indicates sharp edges, corners, or joints nearby. Statement 17: CAUTION: The following label indicates moving parts nearby. Safety...
Page 18 ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 19: Chapter 1. Introduction
Chapter 1. Introduction This Hardware Maintenance Manual contains information to help you solve problems that might occur in the Lenovo ThinkServer TD100 and TD100x Machine Types 6398, 6399, 6419, 6429, 4203, 4204, 4205, and 4206 server. It describes the diagnostic tools that come with the server, error codes and suggested actions, and instructions for replacing failing components.
Page 20: Notices And Statements In This Document
Select your product list. 3. Select Servers from the Brand list. 4. From Family list, select ThinkServer TD100 and TD100x, and click Continue. 5. Click Downloads and drivers to download firmware updates. Notices and statements in this document...
Page 21: Thinkserver Td100 Features And Specifications (Machine Types 6398, 6399, 6419, 6429, 4203, 4204, 4205, And 4206)
ThinkServer TD100 features and specifications (Machine Types 6398, 6399, 6419, 6429, 4203, 4204, 4205, and 4206) The following information is a summary of the features and specifications for Machine Types 6398, 6399, 6419, 6429, 4203, 4204, 4205, and 4206. Depending on the server model, some features might not be available, or some specifications might not apply.
Page 22: Server Controls, Leds, And Connectors
System power LED Power-control button Hard disk drive activity LED System-error LED USB connectors ThinkServer TD100 and TD100x: Hardware Maintenance Manual CD-eject or DVD-eject button Hot-swap hard disk drive status LED (amber) Hot-swap hard disk drive activity LED (green)
Page 23 The following illustration shows the controls, LEDs, and connectors on the front of the simple-swap server models. System power LED Power-control button Hard disk drive activity LED System-error LED Power-on LED When this LED is lit, it indicates that the server is turned on. When this LED is off, it indicates that ac power is not present, or the power supply or the LED itself has failed.
Page 24 When the drive is removed, this LED also is visible on the SAS/SATA backplane, below the hot-swap hard disk drive activity LED. ThinkServer TD100 and TD100x: Hardware Maintenance Manual ™ adapter is installed in the server and the LED...
Page 25: Rear View
Rear view The following illustration shows the LEDs and connectors on the rear of the hot-swap power supply models with optional redundant power. Power cord connectors (some models) AC power LEDs DC power LEDs Mouse connector Keyboard connector Serial 1 (COM 1) connector Parallel connector The following illustration shows the connectors on the rear of the non-hot-swap power supply models.
Page 26 Serial 1 connector Connect a 9-pin serial device to this connector. Parallel connector Connect a parallel device to this connector. ThinkServer TD100 and TD100x: Hardware Maintenance Manual USB 3 and 4 connectors (RJ45) Ethernet 10/100/1000 connector (RJ45) Ethernet 10/100 (for Remote...
Page 27 Video connector Connect a monitor to this connector. USB connectors Connect USB devices to these connectors. Ethernet connector Use this connector to connect the server to a network. Serial 2 connector Connect a 9-pin serial device to this connector. Ethernet transmit/receive activity LED This LED is on the Ethernet connector.
Page 28: Internal Connectors, Leds, And Switches
Power Power USB tape Front panel Primary IDE Front USB Microprocessor 1 Microprocessor 2 ThinkServer TD100 and TD100x: Hardware Maintenance Manual DIMM LEDs SAS/SATA backplane power Simple-swap SATA backplate Hot-swap SAS/SATA signal Hot-swap main fan Hot-swap fan (redundant) Battery Wake on LAN...
Page 29: System-Board External Connectors
System-board external connectors The following illustration shows the external input/output (I/O) connectors on the system board. Mouse Keyboard Serial 1 (COM 1) Parallel Video DIMM LEDs USB (2) (RJ45) Ethernet 10/100/1000 (RJ45) Ethernet 10/100 (for Remote Supervisor Adapter II SlimLine) NMI button Serial 2 (COM 2) Chapter 1.
Page 30: System-Board Option Connectors
The following illustration shows the system-board connectors for user-installable options. DIMM (6) Microprocessor 1 Microprocessor 2 Battery ServeRAID adapter ThinkServer TD100 and TD100x: Hardware Maintenance Manual DIMM LEDs PCI 32 bit/33 MHz PCI-X 64 bit/133 MHz PCI Express x8 (x8) PCI Express x8 (x4) Remote Supervisor Adapter II...
Page 31: System-Board Leds
System-board LEDs The following illustration shows the LEDs on the system board. Microprocessor error LED (2) VRM error LED Battery LED BMC heartbeat LED DIMM LEDs ServeRAID error LED Error LED (6) Microprocessor mismatch LED DIMM error LEDs 1 through 12 Chapter 1.
Page 32: System-Board Switches
2 SW4 (Boot block/Clear CMOS) The following table describes the function of each switch on the system board. Table 2. System board switches Switch number ThinkServer TD100 and TD100x: Hardware Maintenance Manual DIMM LEDs Description Boot block: v When this switch is on 1, this is normal mode.
Page 33: Chapter 2. Configuration Information And Instructions
Updating the firmware The firmware in the server is periodically updated and is available for download on the Lenovo Support Web site. Use the ThinkServer EasyUpdate program to download and install firmware updates. The following items are downloadable from the Web at http://www.lenovo.com/...
Page 34: Using The Configuration/Setup Utility Program
(RAID). Be sure to use these programs as described in this document. The ServeRAID 8k-l SAS Controller that comes with the TD100 server (hot-swap SAS and hot-swap SATA models) enables you to configure multiple physical SAS or SATA hard disk drives to operate as logical drives in a disk array.
Page 35 When the maximum four drives are installed, RAID level-10 is also supported. Note: In addition, when the maximum four drives (for TD100) and the optional ServeRAID-8k Controller are installed in the simple-swap SATA models, the server can also support RAID level-5. See “Installing the RAID-8k adapter” on page 117 for details about installing and cabling the ServeRAID-8k Controller to enable RAID level-5 support on simple-swap SATA models.
Page 36 Serial ATA (SATA) controller comes disabled by default. You must enable it and install the device drivers before you can use it. The device drivers, documentation, and other information are available on the IBM ServeRAID-8e (Adaptec HostRAID) Support CD. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 37 Enabling the Serial ATA (SATA) controller: To enable the SATA RAID controller, complete the following steps: 1. Turn on the server. 2. When the prompt Press F1 for Configuration/Setup appears, press F1. If you have set an administrator password, you are prompted to type the password. 3.
Page 38: Using Raid Manager
Manager to configure the RAID controller. Additional information about ServeRAID Manager is also available from the Help menu. For information about a specific object in the ServeRAID Manager tree, select the object and click Actions → Hints and tips. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 39 Configuring the controller By running ServeRAID Manager in Startable CD mode, you can configure the controller before you install the operating system. The information in this section assumes that you are running ServeRAID Manager in Startable CD mode. To run ServeRAID Manager in Startable CD mode, turn on the server; then, insert the IBM ServeRAID Support CD into the CD or DVD drive.
Page 40: Using The Thinkserver Easystartup Program
The program is contained on the ThinkServer EasyStartup DVD provided with your server. If you did not receive a ThinkServer EasyStartup DVD with your server, you can download an ISO image of the DVD from Lenovo Support Web site (http://www.lenovo.com/support). The program has a built-in help system and User Guide to answer any questions you might have.
Page 41: Using The Boot Menu Program
Using the Boot Menu program The Boot Menu program is a built-in, menu-driven configuration program that you can use to temporarily redefine the first startup device without changing settings in the Configuration/Setup Utility program. To use the Boot Menu program, complete the following steps: 1.
Page 42 ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 43: Chapter 3. Parts Listing, Td100 Types 6398, 6399, 6419, 6429, 4203, And 4206
2. Enter your product number (machine type and model number) or select Servers from the Select your product list. 3. Select Servers from the Brand list. 4. From Family list, select ThinkServer TD100 and TD100x, and click Continue. © Lenovo 2008. Portions © IBM Corp. 2008.
Page 44: Replaceable Server Components
Replaceable components are of three types: v Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility. If Lenovo installs a self-service CRU at your request, you will be charged for the installation. v Optional-service customer replaceable unit: You may install an optional-service CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
Page 45 GHz/1066 MHz (2x 2 MB L2 cache) (models) CRU part number (Self-service) 45J9640 45J9642 45J9644 45J9646 45J9648 46U1024 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number 46U2305 46U2304 41Y9125...
Page 46 Memory, 2GB PC2-5300 CL5 ECC DDR2 Chipkill FBDIMM 667MHz (models) Memory, 4GB PC2-5300 CL5 ECC DDR2 Chipkill FBDIMM 667MHz (models) DIMM air duct (all models) Power supply cage (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 47 Cable, SCSI (all models) Redundant rear 120 mm x 38 mm fans (all models) CRU part number (Self-service) 41Y9068 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 48 Qlogic ISCSI dual port PCI-E adapter (all models) 3U SCSI adapter (all models) Hard drive backplane (all models) MS SW Pack (all models) HDD Inner Cage (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number...
Page 49 Keyboard, China (all models) Keyboard, Japanese (all models) Keyboard, USEng103P (models) Mouse, Opt.Wheel USB (models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 50 SATA II (models 12G) Hard disk drive, 500GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) Hard disk drive, 750GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 51 Microprocessor, Intel Xeon 5150 Dual-Core 2.66 GHz/1333 MHz (2x 2 MB L2 cache) (models) CRU part number (Self-service) 45J9648 46U1024 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 52 FBDIMM 667MHz (models 12G) Memory, 4GB PC2-5300 CL5 ECC DDR2 Chipkill FBDIMM 667MHz (models) DIMM duct (all models) Power supply cage (all models) Filler panel, power supply (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 53 Cable, power LED (all models) Cable, SAS power (all models) Redundant rear 120 mm x 38 mm fans (all models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service)
Page 54 10A C13 to CEE 7/7 2.8M Power Cord Fig.18-2.8M (all models) PRO/1000 GTSV (all models) Qlogic ISCSI single port PCI-E adapter (all models) DD S/5 tape drive (all models) Operator information panel assembly (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 55 Keyboard, China (all models) Keyboard, Japanese (all models) Keyboard, USEng103P (models) Mouse, Opt.Wheel USB (models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 56 Hard disk drive, 250GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) Hard disk drive, 500GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) Hard disk drive, 750GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 57 Microprocessor, Intel Xeon 5140 Dual-Core 2.33 GHz/1333 MHz (2x 2 MB L2 cache) (models) CRU part number (Self-service) 45J9648 46U1024 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 58 FBDIMM 667MHz (models 13U 13F 13S 13L 13D 13Y 13G 13B 13H 13V) Memory, 4GB PC2-5300 CL5 ECC DDR2 Chipkill FBDIMM 667MHz (models) DIMM duct (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number...
Page 59 Cover, Hard drive filler (all models) Blower DIMM blocker (all models) diskette drive interposer (all models) CRU part number (Self-service) 41Y9068 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 60 14K 14R 14E 14J) 3U SCSI adapter (all models) Remote Supervisor Adapter (RSAII) Slimline (all models) RSA Slimline Bracket (all models) SAS Card (all models) SCSI adapter (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 61 Keyboard, China (all models) Keyboard, Japanese (all models) Keyboard, USEng103P (models) Mouse, Opt.Wheel USB (models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 62 14M 14A 14Q 14T 14H 14K 14R 14E 14J) Hard disk drive, 500GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) Hard disk drive, 750GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number...
Page 63 Microprocessor, Intel Xeon 5120 Dual-Core 1.86 GHz/1066 MHz (2x 2 MB L2 cache) (models) CRU part number (Self-service) 45J9648 46U1024 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number...
Page 64 Microprocessor, Intel Xeon X5450 Quad-Core 3.00 GHz/1333 MHz (12 MB L2 cache) Processor (120 W) Processor (models) Microprocessor, 3.2GHz/1066 (all models) Retention module, microprocessor (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 65 13D 13Y 13G 13M 13A 13Q 13T 13B 13H 13V 13K 13R 13E 13J) CRU part number (Self-service) 46U1017 46U1018 46U1019 41Y9068 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number 39Y8499 24R2738...
Page 66 Cooling duct (all models) Fan, rear bracket assembly (all models) Feet, System (all models) Filler bezel (all models) iSCSI TX server adapter (all models) Feet, system (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 67 Diag Panel Asm (all models) PSU INTERPOSER (all models) Planar Tray (all models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- FRU part service) number 26K7363...
Page 68 Keyboard, Preferred Pro with 2m cable - Full Width - Black - USB (all models) Keyboard, China (all models) Keyboard, Japanese (all models) Keyboard, USEng103P (models) Mouse, Opt.Wheel USB (models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 69 Hard disk drive, 500GB 7200 RPM 3.5-inch Hot-Swap SATA II (models) CRU part number (Self-service) 45J9632 45J9634 45J9640 45J9642 45J9644 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- service) part number 24R2694 24R2720 41Y9083 39Y8355...
Page 70 Microprocessor, Intel Xeon 5150 Dual-Core 2.66 GHz/1333 MHz (2x 2 MB L2 cache) (models) Microprocessor, Intel Xeon 5160 Dual-Core 3.0 GHz/1333 MHz (2x 2 MB L2 cache) (models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number...
Page 71 Adapter, NetXtreme 1000 SX + Fiber Ethernet adapter (all models) CRU part number (Self-service) 46U1017 46U1018 46U1019 Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- service) part number 41Y8905 43W5174 43W5175...
Page 72 Service Label (all models) Fan, rear bracket assembly (all models) Thermal grease (all models) 3U SCSI adapter (all models) Remote Supervisor Adapter (RSAII) Slimline (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 73 Keyboard, Japanese (all models) Keyboard, USEng103P (models) Mouse, Opt.Wheel USB (models) DIMM BLOCKER (all models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- service) part number 41Y9086...
Page 74 (models) Hard disk drive, 500GB 7200 RPM 3.5″ Simple-Swap SATA II (models) Hard disk drive, 450GB 15K SAS 3.5″ HS (all models) Adv Lenovo Bezel (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number...
Page 75 GHz/1333 MHz (2x 4 MB L2 cache) (models) Microprocessor, Intel Xeon E5405 Quad-Core 2.00 GHz/1333 MHz (12 MB L2 cache) Processor (models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- service) part number...
Page 76 Chassis (all models) Battery, 3.0 volt (all models) Cable, DVD signal, IDE (all models) diskette drive Interposer (all models) fan harness (all models) Dual USB (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional-...
Page 77 Hard drive filler (all models) Cover Button (all models) Operator information panel assembly (all models) CRU part number (Self-service) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206 CRU part number (Optional- service) part number 39Y8356...
Page 78 Keyboard, Preferred Pro with 2m cable - Full Width - Black - USB (all models) Keyboard, China (all models) Keyboard, Japanese (all models) Keyboard, USEng103P (models) Mouse, Opt.Wheel USB (models) DIMM BLOCKER (all models) ThinkServer TD100 and TD100x: Hardware Maintenance Manual CRU part CRU part number number (Optional- (Self-service)
Page 79: Power Cords
Power cords For your safety, Lenovo provides a power cord with a grounded attachment plug to use with this Lenovo product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet. Lenovo power cords used in the United States and Canada are listed by Underwriter’s Laboratories (UL) and certified by the Canadian Standards...
Page 80 39M5199 39M5068 39M5226 39M5179 39M5233 ThinkServer TD100 and TD100x: Hardware Maintenance Manual Used in these countries and regions Bangladesh, Lesotho, Macao, Maldives, Namibia, Nepal, Pakistan, Samoa, South Africa, Sri Lanka, Swaziland, Uganda (models 11G 11A) Abu Dhabi, Bahrain, Botswana, Brunei Darussalam, Channel Islands, China (Hong Kong S.A.R.), Cyprus, Dominica, Gambia,...
Page 81 Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico, Micronesia (Federal States of), Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Thailand, Taiwan, United States of America, Venezuela (models) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206...
Page 82 39M5199 39M5068 39M5226 39M5179 39M5233 ThinkServer TD100 and TD100x: Hardware Maintenance Manual Used in these countries and regions 110 - 120 V Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El...
Page 83 Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico, Micronesia (Federal States of), Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Thailand, Taiwan, United States of America, Venezuela (models) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206...
Page 84 39M5199 39M5068 39M5226 39M5179 39M5233 ThinkServer TD100 and TD100x: Hardware Maintenance Manual Used in these countries and regions 110 - 120 V Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El...
Page 85 Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico, Micronesia (Federal States of), Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Thailand, Taiwan, United States of America, Venezuela (models) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206...
Page 86 39M5199 39M5068 39M5226 39M5179 39M5233 ThinkServer TD100 and TD100x: Hardware Maintenance Manual Used in these countries and regions 110 - 120 V Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El...
Page 87 Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico, Micronesia (Federal States of), Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Thailand, Taiwan, United States of America, Venezuela (models) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206...
Page 88 39M5199 39M5068 39M5226 39M5179 39M5233 ThinkServer TD100 and TD100x: Hardware Maintenance Manual Used in these countries and regions 110 - 120 V Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El...
Page 89 12G 13G 13S 13L 13Y 14G 15S 15L 15Y 15G 16S 17S 18S 16L 17L 18L 16Y 17Y 18Y 16G 17G 18G 19G) 39M5172 Israel (models 11G 12G 13G 14G 15G 16G 17G 18G 19G) Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206...
Page 90 39M5199 39M5068 39M5226 39M5179 39M5233 ThinkServer TD100 and TD100x: Hardware Maintenance Manual Used in these countries and regions 220 - 240 V Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El...
Page 91: Chapter 4. Removing And Replacing Server Components
Replaceable components are of three types: v Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility. If Lenovo installs a self-service CRU at your request, you will be charged for the installation. v Optional-service customer replaceable unit: You may install an optional-service CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
Page 92: System Reliability Guidelines
When you are finished working on the server, reinstall all safety shields, guards, labels, and ground wires. v For a list of options for the server, see http://www.lenovo.com/accessories/. System reliability guidelines To help ensure proper cooling and system reliability, make sure that: v Each of the drive bays has a drive or a filler panel and electromagnetic compatibility (EMC) shield installed in it.
Page 93: Handling Static-Sensitive Devices
Handling static-sensitive devices Attention: To avoid damage, keep static-sensitive devices in their static-protective packages until you are ready to install them. To reduce the possibility of damage from electrostatic discharge, observe the following precautions: v Limit your movement. Movement can cause static electricity to build up around you.
Page 94: Removing And Replacing Self-Service Crus
Removing and replacing Self-service CRUs Replacement of Self-service CRUs is your responsibility. If Lenovo installs a self-service CRU at your request, you will be charged for the installation. The illustrations in this document might differ slightly from your hardware. Removing the bezel To remove the bezel, complete the following steps: 1.
Page 95: Replacing The Bezel
Replacing the bezel To replace the bezel, complete the following steps: 1. Insert the tabs on the bezel into the slots on the server chassis. 2. Rotate the bezel toward the server until it snaps in place. Chapter 4. Removing and replacing server components...
Page 96: Removing The Side Cover
6. If you are instructed to return the side cover, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Operating the server for more than 30 minutes with the side cover...
Page 97: Installing The Side Cover
Installing the side cover Attention: the server. Operating the server for extended periods of time (more than 30 minutes) with the side cover removed might damage server components. To install the side cover, complete the following steps. 1. Make sure that all cables, adapters, and other components are installed and seated correctly and that you have not left loose tools or parts inside the server.
Page 98: Turning The Stabilizing Feet
In some cases, you might need a screwdriver to pry the feet from the server. 3. Reinstall the feet in the opposite location. The tab on the feet should extend beyond the edge of the server. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Feet...
Page 99: Removing An Adapter
Removing an adapter To remove an adapter, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables.
Page 100: Installing An Adapter
. Note: Make sure that the adapter is seated correctly in the expansion slot before you turn on the server. Incomplete installation of an adapter might damage the system board or the adapter. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 101 Rear adapter-retention bracket Adapter Front adapter-retention bracket 7. Rotate the rear and front adapter-retention brackets to the closed position. 8. Connect required cables to the adapter. Route cables so that they do not block the flow of air from the fans. 9.
Page 102: Removing And Installing Internal Drives
The following is an illustration of the hot-swap server models. Bay 1 Bay 2 Bay 3 Bay 4 Bay 5 Bay 6 The following is an illustration of the simple-swap server models. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Bay 7 Bay 8 Bay 9 Bay 10 Bay 11...
Page 103 Bay 1 Bay 2 Bay 3 Bay 4 Bay 5 Bay 6 Bay 7 Chapter 4. Removing and replacing server components...
Page 104 9. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual lever and pull the power supply out of the bay, using the handle.
Page 105 Installing a CD or DVD drive To install a CD or DVD drive, complete the following steps: 1. If you are replacing a removed drive with a new drive, make sure that: v You have all the cables and other equipment that is specified in the documentation that comes with the new drive.
Page 106 9. Return the power-supply cage handle to the locked position. ThinkServer TD100 and TD100x: Hardware Maintenance Manual lever and pull the power supply out of the bay, using the handle. assembly all the way up until the retainer latch locks the cage in place...
Page 107 10. If you have a hot-swap model, reinstall the hot-swap power supplies (see “Installing a hot-swap power supply” on page 96). 11. Install the side cover (see “Installing the side cover” on page 79). 12. Lock the side cover. 13. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.
Page 108 7. Align the drive assembly with the guide rails in the bay 3 ; then, carefully slide the drive assembly into the drive bay until the drive snaps into place. 8. Rotate the drive tray handle to the closed position. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 109 9. Check the hard disk drive status indicator to make sure that the hard disk drive is operating correctly. (You might have to restart the server for the drive to be recognized.) If the amber hard disk drive status LED for a drive is lit continuously, it indicates that the drive is faulty and must be replaced.
Page 110 7. If you are instructed to return the drive assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Simple-swap hard disk drives are not hot-swappable. Disconnect all...
Page 111 Installing a simple-swap hard disk drive Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before removing or installing a simple-swap hard disk drive. To install a simple-swap hard disk drive, complete the following steps. 1.
Page 112: Removing A Hot-Swap Power Supply
Removing a hot-swap power supply This procedure applies only to server models that have hot-swap power supplies. See “Removing a non-hot-swap power supply cage assembly (TD100 - some models)” on page 132 for information about the removal of a non-hot-swap power supply.
Page 113 Statement 17: CAUTION: The following label indicates moving parts nearby. To remove a hot-swap power supply, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Disconnect the power cord from the power supply that is to be removed. 3.
Page 114: Installing A Hot-Swap Power Supply
Installing a hot-swap power supply This procedure applies only to server models that have hot-swap power supplies. See “Installing a non-hot-swap power supply cage assembly (TD100 - some models)” on page 135 for information about the installation of a non-hot-swap power supply.
Page 115: Removing A Memory Module
Removing a memory module To remove a dual inline memory module (DIMM), complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables.
Page 116: Installing A Memory Module
Note: DIMM connectors 3, 6, 9, and 12 are not functional for ThinkServer TD100 models. Do not install DIMMs in these four connectors and do not remove the DIMM thermal baffles installed in these connectors unless you need to replace the system board.
Page 117 12 (ThinkServer TD100x Machine Types 4203, 4204, 4205, and 4206) Note: For ThinkServer TD100 models (Machine Types 6398, 6399, 6419, 6429, 4203, and 4206), DIMM connectors 3, 6, 9, and 12 are not functional. Do not install DIMMs in these connectors.
Page 118 12 (ThinkServer TD100x Machine Types 4203, 4204, 4205, and 4206) Note: For ThinkServer TD100 models (Machine Types 6398, 6399, 6419, 6429, 4203, and 4206), DIMM connectors 3, 6, 9, and 12 are not functional. Do not install DIMMs in these connectors.
Page 119 Table 15 on page 99 and Table 16 on page 100 Note: DIMM connectors 3, 6, 9, and 12 are not functional in ThinkServer TD100 models. Do not install DIMMs in these connectors. Attention: To avoid breaking the retaining clips or damaging the DIMM connectors, open and close the clips gently.
Page 120 10. Rotate the power-supply cage assembly back into the server. Press the power-supply cage release tab 1 and rotate the power-supply cage assembly into the chassis. ThinkServer TD100 and TD100x: Hardware Maintenance Manual DIMM 7 DIMM 10 DIMM 12 connector...
Page 121 11. If you have a hot-swap model, reinstall the hot-swap power-supplies. If you have other options to install or remove, do so now; otherwise, go to “Installing the side cover” on page 79. Chapter 4. Removing and replacing server components...
Page 122: Removing A Hot-Swap Fan
4. If you are instructed to return the fan, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 123: Installing A Hot-Swap Fan
Installing a hot-swap fan Attention: v Replace a failed fan within 48 hours. v To ensure proper cooling and airflow, do not operate the server for more than 30 minutes with the side cover removed. To install a hot-swap fan, complete the following steps. 1.
Page 124: Removing The Rear System Fan Cage Assembly With Baffle
2. Insert the rear system fan assembly retainer tabs into the corresponding mounting tabs on the chassis; then, slide the rear fan cage assembly 1 to the right until it locks into the mounting tabs on the chassis. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 125 3. Connect the rear fan 1 cage assembly cable to the system board (see “System-board internal connectors” on page 10 for the location of the rear fan assembly connector). 4. Install the side cover (see “Installing the side cover” on page 79). 5.
Page 126: Removing The Front System Fan Cage Assembly
ThinkServer TD100 and TD100x: Hardware Maintenance Manual lever and pull the power supply out of the bay, using the handle. assembly all the way up until the retainer latch locks the cage in place on the chassis.
Page 127: Installing The Front System Fan Cage Assembly
Installing the front system fan cage assembly Attention: v Replace a failed fan within 48 hours. v To ensure proper cooling and airflow, do not operate the server for more than 30 minutes with the side cover removed. To install the front system fan cage assembly, complete the following steps. 1.
Page 128: Removing The Front Usb Connector Assembly
8. Carefully pull the front USB cable out of the opening in the chassis. 9. If you are instructed to return the front USB connector assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 129: Installing The Front Usb Connector Assembly
Installing the front USB connector assembly To install the front USB connector assembly, complete the following steps. 1. Carefully feed the front USB cable through the opening in the front of the chassis. 2. Squeeze the spring clips on the sides of the front USB connector assembly and insert the assembly into the housing through the back of the housing.
Page 130: Installing The Rear Adapter Retention Bracket
4. Install the side cover (see “Installing the side cover” on page 79). 5. Lock the side cover if it was unlocked during removal. 6. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 131: Removing The Front Adapter-Retention Bracket
Removing the front adapter-retention bracket To remove the front adapter-retention bracket, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables.
Page 132: Removing And Replacing Tier 2 Crus
Removing and replacing Tier 2 CRUs You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for the server. The illustrations in this document might differ slightly from your hardware.
Page 133: Removing The Raid 8K-L Adapter
Statement 2: CAUTION: When replacing the lithium battery, use only Lenovo Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Page 134: Installing The Raid 8K-L Adapter
The ServeRAID-8k adapter can be installed only in its dedicated connector on the system board. See the following illustration for the location of the connector 2 on ThinkServer TD100 and TD100x: Hardware Maintenance Manual To avoid breaking the retaining clips or damaging the...
Page 135: Installing The Raid-8K Adapter
the system board. The ServeRAID-8k adapter 1 is not cabled to the system board, and no rerouting of the SAS or SATA cable is required. To remove the ServeRAID-8k adapter, complete the following. 1. Read the safety information that begins on page vii and “Handling static-sensitive devices”...
Page 136 Hot-swap SAS/SATA 1 connector on the system board. See “System-board internal connectors” on page 10 for the location of these connectors on the system board. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Battery mounting clips Battery cable connector...
Page 137 Note: Remove the dust shield 1 (if one is present) from the Hot-swap SAS/SATA 1 signal connector 2 on the system board before installing the signal cable. Carefully grasp the dust shield and pull it out of the signal connector. b.
Page 138: Dimm Air Duct
5. Remove the four screws securing the DIMM air duct to the power supply cage. ThinkServer TD100 and TD100x: Hardware Maintenance Manual SAS/SATA backplane 1 RAID level-5 enabler plug...
Page 139: Installing The Dimm Air Duct
Plastic push pin Positioning pins 6. Push the air duct up toward the rear of the power supply cage. Once the locator pins are free of the power supply cage you can remove the air duct from the server. Installing the DIMM air duct To install a replacement DIMM air duct, complete the following steps: 1.
Page 140: Removing The Control-Panel Assembly
9. Locate the control-panel assembly release latch just above bay 1. ThinkServer TD100 and TD100x: Hardware Maintenance Manual lever and pull the power supply out of the bay, using the handle. assembly all the way up until the retainer latch locks the cage in place...
Page 141 10. Press up on the release latch 1 of the control-panel assembly 2 and pull the assembly toward the rear of the server. After you pull the assembly out approximately half-way, start turning it downward and pull it out of the chassis. 11.
Page 142: Installing The Control-Panel Assembly
10. Install the side cover (see “Installing the side cover” on page 79). 11. Lock the side cover. 12. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 143: Removing And Replacing Frus
Removing and replacing FRUs Field replaceable units (FRUs) must be installed only by trained service technicians. Removing the hot-swap power-supply cage assembly To remove the hot-swap power-supply cage assembly, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73.
Page 144 7. If you are instructed to return the power-supply cage, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 145: Installing The Hot-Swap Power-Supply Cage Assembly
Installing the hot-swap power-supply cage assembly To install the hot-swap power-supply cage assembly, complete the following steps. 1. Align the screw holes on the power-supply cage 1 pivot bracket with the corresponding screw holes on the rear of the chassis. Support the cage while you install the three screws 2 to secure the pivot bracket on the power-supply cage to the chassis.
Page 146: Removing The Simple-Swap Backplate (Td100 - Some Models)
7. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing the simple-swap backplate (TD100 - some models) This procedure applies only to server models that have a simple-swap backplate installed on the back of the hard disk drive cage.
Page 147 v Non-hot-swap models, lift up the power-supply cage handle and pull the power-supply cage assembly all the way up until the retainer latch locks the cage in place on the chassis. 5. Remove the front fan-cage assembly (see “Removing the front system fan cage assembly”...
Page 148: Installing The Simple-Swap Backplate (Td100 - Some Models)
Installing the simple-swap backplate (TD100 - some models) This procedure applies only to server models that have a simple-swap backplate installed on the back of the hard disk drive cage. To install the simple-swap backplate, complete the following steps. 1. Insert the bottom tabs of the simple-swap backplate with the slots on the lower lip of the drive cage.
Page 149: Removing The Sas/Sata Backplane
Removing the SAS/SATA backplane To remove the SAS/SATA backplane, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables.
Page 150: Installing The Sas/Sata Backplane
11. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing a non-hot-swap power supply cage assembly (TD100 - some models) This procedure applies only to server models that have a non-hot-swap power supply.
Page 151 Statement 11: CAUTION: The following label indicates sharp edges, corners, or joints nearby. Statement 17: CAUTION: The following label indicates moving parts nearby. To remove a non-hot-swap power supply cage assembly, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73.
Page 152 Power supply assembly 7. If you are instructed to return the power supply, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Power supply retaining screws...
Page 153: Installing A Non-Hot-Swap Power Supply Cage Assembly (Td100 - Some Models)
Installing a non-hot-swap power supply cage assembly (TD100 - some models) To install a non-hot-swap power supply, complete the following steps. 1. Align the screw holes in power supply cage pivot bracket with the corresponding screw holes on the rear of the chassis.
Page 154: Installing The Hot-Swap Power Supply Docking Cable Assembly
6. Install the side cover (see “Installing the side cover” on page 79). 7. Lock the side cover. 8. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 155: Removing The Microprocessor And Heat Sink
Removing the microprocessor and heat sink To remove the microprocessor and heat sink, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables.
Page 156 13. If you are instructed to return the microprocessor and heat sink, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Heat sink locking lever Microprocessor...
Page 157: Installing A Microprocessor And Heat Sink
Installing a microprocessor and heat sink Important: Some models support dual-core processors and quad-core processors. Do not mix dual-core and quad-core processors in the same server. Install all dual-core processors or all quad-core processors in the server. To install the microprocessor and heat sink, complete the following steps. Heatsink 2 Microprocessor 2 1.
Page 158 7. If installing a second microprocessor, install a VRM in the VRM connector on the system board. a. Open the retaining clips on each end of the VRM connector. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Heat-sink locking lever Microprocessor...
Page 159: Thermal Grease
b. Turn the VRM so that the keys align with the slot. c. Insert the VRM into the connector by aligning the edges of the VRM with the slots at the end of the VRM connector. Firmly press the VRM straight down into the connector by applying pressure on both ends of the VRM simultaneously.
Page 160 Note: 0.01mL is one tick mark on the syringe. If the grease is properly applied, approximately half (0.22 mL) of the grease will remain in the syringe. 6. Install the heat sink onto the microprocessor as described in “Installing a microprocessor and heat sink” on page 139. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 161: Removing The System Board
Removing the system board To remove the system board, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 73. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables.
Page 162 12. If you are instructed to return the system board, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Handle Release lever Handle...
Page 163: Installing The System Board
Installing the system board To install the system board, complete the following steps. 1. Grasp the system board by the handles and insert the system board into the chassis at a slanted angle and slide it toward the rear of the server until it fully locks into place on the chassis.
Page 164: Easy Led Diagnostics Panel (Td100X Only)
2. Rotate the panel counter clockwise until it clicks into place. 3. Connect the cable to the system board. 4. Install the left-side cover and close the bezel. 5. Reconnect power cords and external cables. ThinkServer TD100 and TD100x: Hardware Maintenance Manual Release Tab...
Page 165: Chapter 5. Diagnostics
If POST detects a problem, more than one beep might sound, or an error message is displayed. See “POST beep codes” on page 148 and “POST error codes” on page 155 for more information. © Lenovo 2008. Portions © IBM Corp. 2008.
Page 166: Post Beep Codes
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 167 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 168 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 169 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 170: No-Beep Symptoms
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 171: Error Logs
Error logs The POST error log contains the three most recent error codes and messages that were generated during POST. The BMC log and the system-event log contain messages that were generated during POST and all system status messages from the service processor.
Page 172: Viewing Error Logs From The Configuration/Setup Utility Program
9. Insert the Diagnostics CD into the CD or DVD drive. 10. Select Save & Exit Setup and follow the prompts. The diagnostics will load. 11. From the top of the screen, select Hardware Info. 12. From the list, select BMC Log. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 173: Post Error Codes
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 174 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 175 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 176 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 177 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 178 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 179 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 180 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 181 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 182 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 183 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 184 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 185 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 186 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 187 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 188: Checkout Procedure
For information about power-supply problems, see “Solving power problems” on page 213. v For intermittent problems, check the error log; see “Error logs” on page 153 and “Diagnostic programs, messages, and error codes” on page 189. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 189: Performing The Checkout Procedure
Check the power supply LEDs, see “Power-supply LEDs” on page 187. b. Turn off the server and all external devices. c. Check all internal and external devices for compatibility at http://www.lenovo.com/support. d. Check all cables and power cords. e. Set all display controls to the middle positions.
Page 190: Troubleshooting Tables
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 191: Diskette Drive Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 192: General Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 193: Intermittent Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 194 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 195: Memory Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 196: Microprocessor Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 197 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 198 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 199: Optional-Device Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 200: Power Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 201: Serial Port Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 202: Serverguide Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 203: Universal Serial Bus (Usb) Port Problems
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 204: Error Leds
If an error occurs, view the server LEDs in the following order: 1. Check the control-panel assembly on the front of the server. If the system-error LED is lit, it indicates that an error has occurred. ThinkServer TD100 and TD100x: Hardware Maintenance Manual DIMM LEDs Microprocessor 1...
Page 205: Power-Supply Leds
2. Check the front and rear of the server to determine whether any component LEDs are lit. 3. Remove the server cover and look inside the server for lit LEDs. Certain components inside the server have LEDs that will be lit to indicate the location of a problem.
Page 206 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 207: Diagnostic Programs, Messages, And Error Codes
Diagnostic programs, messages, and error codes The diagnostic programs are the primary method of testing the major components of the server. As you run the diagnostic programs, text messages and error codes are displayed on the screen and are saved in the test log. A diagnostic text message or error code indicates that a problem has been detected;...
Page 208: Diagnostic Text Messages
2. To save the test log to a diskette, you must use a diskette that you have formatted yourself; this function does not work with preformatted diskettes. If the diskette has sufficient space for the test log, the diskette can contain other data. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 209: Diagnostic Error Codes
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 210 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 211 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 212 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 213 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 214 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 215 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 216 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 217 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 218 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 219 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 220 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 221: Recovering From A Bios Update Failure
Recovering from a BIOS update failure If power to the server is interrupted while BIOS code is being updated, the server might not restart correctly or might not display video. If this happens, complete the following steps to recover: 1. Read the safety information that begins on page vii and “Handling static-sensitive devices”...
Page 222 The following table describes the function of each switch on the system board. Table 17. System board switches Switch number ThinkServer TD100 and TD100x: Hardware Maintenance Manual Description Boot block: v When this switch is on 1, this is normal mode.
Page 223: System-Error Log Messages
Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 224 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 225 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 226 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 227 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 228 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 229 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 230 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Page 231: Solving Scsi Problems
Solving SCSI problems Note: This information also applies to Serial Attached SCSI (SAS) problems. For any SCSI error message, one or more of the following devices might be causing the problem: v A failing SCSI device (adapter, drive, or controller) v An incorrect SCSI termination jumper setting v A missing or incorrectly installed SCSI terminator v A defective SCSI terminator...
Page 232: Solving Ethernet Controller Problems
Make sure that the device drivers on the client and server are using the same protocol. If the Ethernet controller still cannot connect to the network but the hardware appears to be working, the network administrator must investigate other possible causes of the error. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 233: Solving Undetermined Problems
Turn on the server and reconfigure it each time. v Any external devices. v Surge-suppressor device (on the server). v Modem, printer, mouse, and non-Lenovo devices. v Each adapter. v Hard disk drives. v Memory modules. The minimum configuration requirement is two 512 MB DIMM on the system board.
Page 234: Calling Lenovo For Service
Adapters and attachments, in the same locations v Address jumpers, terminators, and cabling v Software versions and levels v Memory amount, type and configuration v Diagnostic program type and version level v Configuration option settings v Operating-system control-file setup ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 235: Getting Help And Technical Assistance
Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This section contains information about where to go for...
Page 236: Calling For Service
Hardware and software configuration information Using other services If you travel with a Lenovo notebook computer or relocate your computer to a country where your desktop, notebook, or server machine type is sold, your computer might be eligible for International Warranty Service, which automatically entitles you to obtain warranty service throughout the warranty period.
Page 237: Purchasing Additional Services
Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at http://www.lenovo.com/. Lenovo Taiwan product service ®...
Page 238 ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 239: Appendix. Notices
Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
Page 240: Trademarks
Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Lenovo logo The following terms are trademarks of International Business Machines Corporation...
Page 241: Waste Electrical And Electronic Equipment (Weee) Notices
Lenovo makes no representations or warranties with respect to non-Lenovo products. Support (if any) for the non-Lenovo products is provided by the third party, not Lenovo. Some software might differ from its retail version (if available) and might not include user manuals or all program functionality.
Page 242: Battery Return Program
European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Directive. ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 243: Electronic Emissions Notices
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Lenovo is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
Page 244: Industry Canada Class A Emission Compliance Statement
Grenzwerte der EN 55022 Klasse A ein. Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden. Lenovo übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der Lenovo verändert bzw.
Page 245: Japanese Voluntary Control Council For Interference (Vcci) Statement
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland) GmbH, Gropiusplatz 10, D-70563 Stuttgart. Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022...
Page 246: Taiwanese Class A Warning Statement
Taiwanese Class A warning statement Chinese Class A warning statement Korean Class A warning statement ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 247: Index
22 integrated SATA controller 19 minimum 215 SAS/SATA controller 17 ServeRAID controller 21 summary window 21 © Lenovo 2008. Portions © IBM Corp. 2008. configuration utility IBM ServeRAID starting 18 Configuration/Setup Utility program 16 configuring the server 15 connector...
Page 248 176 power 182 serial port 183 ServerGuide 184 software 184 USB port 185 video 178 ThinkServer TD100 and TD100x: Hardware Maintenance Manual errors beep codes 148 format, diagnostic code 190 messages, diagnostic 189 Ethernet activity LED 6, 9...
Page 249 hot-plug adapter. See adapter hot-swap and hot-plug devices adapters 116 hot-swap drive specifications 3 hot-swap drives SAS backplane LEDs 6 hot-swap drives, SAS or SATA installing 90 removing 89 hot-swap fan installing 105 hot-swap power supply removing 95 important notices 2 installation order memory modules 100, 101 installing...
Page 250 174 intermittent 175 keyboard 175 memory 177 microprocessor 178 monitor 178 mouse 176 ThinkServer TD100 and TD100x: Hardware Maintenance Manual problems (continued) optional devices 181 pointing device 176 POST/BIOS 155 power 182, 213 serial port 183 ServerGuide 184...
Page 251 SAS backplane installing 132 LEDs hot-swap drive activity 6 hot-swap drive status 6 SAS or SATA hot-swap drives installing 90 removing 89 SAS/SATA backplane removing 131 SAS/SATA Configuration Utility 17 SAS/SATA controller configuring 18 viewing the configuration 18 SAS/SATA HostRAID feature using 17 SATA RAID enabling 19...
Page 252 178 viewing the configuration SAS/SATA controller 18 Serial ATA controller 20 installing 141 web site publication ordering 217 support 217 Web site Lenovo support 2, 25 weight 3 ThinkServer TD100 and TD100x: Hardware Maintenance Manual...
Page 254 Part Number: 46U0860 Printed in USA (1P) P/N: 46U0860...

This manual is also suitable for:

Thinkserver td100x

Lenovo ThinkServer TD100 Hardware Maintenance Manual

Safety

Chapter 1. Introduction

Chapter 2. Configuration Information and Instructions

Chapter 3. Parts Listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206

Chapter 4. Removing and Replacing Server Components

Chapter 5. Diagnostics

Getting Help and Technical Assistance

Appendix. Notices

Quick Links

Related Manuals for Lenovo ThinkServer TD100

Summary of Contents for Lenovo ThinkServer TD100

This manual is also suitable for:

Table of Contents