Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele G 1XXX Series
Summary of Contents for Miele G 1XXX Series
-
Page 1: Operating Instructions
Operating instructions for dishwashers To avoid the risk of accidents or en - AUS, NZ damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. -
Page 2: Table Of Contents
Contents Guide to the appliance ..........5 Appliance overview . - Page 3 Contents Operation ............32 Detergent .
- Page 4 Plumbing............61 The Miele waterproof anti-leak system ....... . . 61 Connection to the water supply .
-
Page 5: Guide To The Appliance
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Child safety lock in door grip (not visible) d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent... -
Page 6: Control Panel
Guide to the appliance Control panel a Programmes d Check/Refill indicators b Programme selector button e Programme sequence indicators f On/Off button K c Start/Stop button with indicator light This instruction book applies to several different dishwasher models. The specific dishwasher models below are referred to as follows: G 1142 etc. -
Page 7: Warning And Safety Instructions
Warning and Safety instructions Safety with children This appliance conforms to current This appliance is not a toy! To avoid safety requirements. Inappropriate the risk of injury, keep children well use can, however, lead to personal away and do not allow them to play in injury and damage to property. - Page 8 Warning and Safety instructions Technical safety Do not connect the dishwasher to the mains supply until it has been fully Before setting up the appliance, installed. check it for any externally visible damage. Under no circumstances Before connecting the appliance, should you use a damaged appliance.
- Page 9 If the connection cable is damaged where it can be seen that this is it must be replaced with a Miele cable necessary. by a Miele approved service technician – The stopcock has been turned off only.
-
Page 10: Correct Use
Warning and Safety instructions Installation Correct use The dishwasher must be installed Do not use solvents in the and connected in compliance with the dishwasher. Danger of explosion. installation instructions. Do not inhale or ingest dishwasher The dishwasher must be correctly detergent. - Page 11 Warning and Safety instructions Accessories Inadvertently filling the salt reservoir with powder or liquid dishwasher Only use genuine Miele spare parts detergent will damage the water and accessories with this appliance. If softener. Make sure you have picked spare parts or accessories from other...
-
Page 12: Caring For The Environment
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for disposal human health and to the environment. -
Page 13: Energy Saving Washing
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies. -
Page 14: Before Using For The First Time
Before using for the first time To open the door Safety lock ^ Press the release catch inside the Use the safety lock to prevent children door grip upwards and pull the door opening the dishwasher door. open. ^ To lock the door, push the slide If the door is opened during operation underneath the door grip to the right. -
Page 15: Water Softener
Before using for the first time Water softener The dishwasher is set at the factory for a hardness level of 0.2 - In order to achieve good cleaning 0.7 mmol/l (1 - 4 °d). results, the dishwasher needs to operate with soft water. Hard water If this setting corresponds to the results in the build-up of calcium hardness of your water you do not need... -
Page 16: To Programme The Water Hardness Level
Before using for the first time To programme the water hardness The number of times the Wash/Rinse programme sequence indicator flashes level tells you the value which has been set Each time a button is pressed, one of (see chart). the indicator lights will flash and light up in the control panel. -
Page 17: Checking The Programmed Water Hardness Level
Before using for the first time Checking the programmed water hardness level ^ Switch the dishwasher off with the On/Off button K. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K. -
Page 18: Before Using The Appliance For The First Time You Require
Before using for the first time Before using the appliance for If the water in your area is very soft the first time you require: and constantly lower than – Approx. 2 litres of water, 0.7 mmol/l (4 °d) you should still add salt before using the –... -
Page 19: Salt Indicator
Before using for the first time ^ Remove the lower basket and Salt indicator unscrew the salt reservoir cap. ^ Fill the salt reservoir with dishwasher salt when the salt indicator light Water or saline solution will run out comes on. (If it comes on during a of the reservoir when the cap is programme, wait until the end of the removed. -
Page 20: Rinse Aid
Before using for the first time Rinse aid If you only ever use combination Rinse aid is necessary to ensure water products in your dishwasher, you do does not cling and leave marks on not need to add rinse aid. crockery during the drying phase and helps crockery dry faster after it has Adding rinse aid... -
Page 21: Rinse Aid Indicator
Before using for the first time Rinse aid indicator When the light comes on the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. ^ Add rinse aid only until it is visible in the opening. -
Page 22: Setting The Rinse Aid Dosage
Before using for the first time ^ Press the programme selector button Setting the rinse aid dosage three times. You can adjust the rinse aid dosage for best results. The lowest programme indicator will flash briefly three times at intervals. The rinse aid dosage can be set from approx. -
Page 23: Loading The Dishwasher
Loading the dishwasher Note – Wide based items should be placed at an angle so that water can run off Remove coarse food residues from them freely. crockery. – The spray arms must not be blocked There is no need to rinse items under by items which are too tall or hang running water. -
Page 24: Items Not Suitable For Dishwashers
Loading the dishwasher Items not suitable for We recommend: dishwashers: – When purchasing new crockery and cutlery, make sure they are – Wooden cutlery and crockery or dishwasher-proof. items with wooden parts: these may discolour and fade. The glue used in –... -
Page 25: Upper Basket
Loading the dishwasher Upper basket Hinged cup rack ^ To make room for tall items, raise the For safety reasons, do not rack upwards. operate the dishwasher without the upper and lower baskets in place. Positioning rail (depending on model) Glasses can be arranged along the positioning rail to give them some support during the programme. -
Page 26: Universal Support (Depending On Model)
Loading the dishwasher Universal support (depending on model) This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it. -
Page 27: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or upper basket, the upper basket can be Dishwasher with cutlery tray adjusted on three levels with 2 cm (see data plate for model number) -
Page 28: Lower Basket
Loading the dishwasher Lower basket Hinged spikes ^ For larger and heavier items such as The spikes are used for washing plates plates, serving platters, saucepans, and saucers. bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket. -
Page 29: Removable Spiked Insert
Loading the dishwasher Removable spiked insert Bottle holder (depending on model) You can remove the spiked insert to The bottle holder can be used to wash make more room for larger items of narrow items, e.g. milk and baby crockery, e.g. a large, flat pot, or bottles. -
Page 30: Cutlery
Loading the dishwasher Cutlery Cutlery tray (depending on model) If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 31: Cutlery Basket (Depending On Model)
Loading the dishwasher Cutlery basket (depending on model) ^ Fit it into the cutlery basket if required. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. -
Page 32: Operation
Miele branded dishwasher powder change to a different product or use a and tabs are available from the Miele traditional dishwasher detergent. Spare Parts Department or via the Internet, depending on country. - Page 33 Operation Dispensing Avoid inhalation of powder ^ Follow the dosage recommended by detergents and do not ingest the manufacturer on the packaging. dishwasher detergent. Dishwasher ^ Unless directed otherwise, use one detergents contain irritant or corrosive detergent tab or add 20 to 30 ml ingredients which can cause burning detergent in compartment II, in the nose, mouth and throat if...
-
Page 34: Adding Detergent
Operation ^ Make sure that the detergent Adding detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy. For information Compartment I holds max. 10 ml, Compartment II holds max. 50 ml. There are markings in compartment II to assist with dispensing: 20, 30. -
Page 35: Switching On
Operation Switching on Starting a programme ^ Make sure the spray arms are not ^ Select the programme required with obstructed. the programme selector button. ^ Close the door. The indicator light next to the selected programme will come on. ^ Open the stopcock, if it is closed. -
Page 36: At The End Of A Programme
Operation At the end of a programme Unloading the dishwasher The End indicator light will come on at Dishes tend to break and chip more the end of the programme. easily when they are hot. Allow the dishes to cool until they are The dishwasher can now be opened comfortable enough to handle before and unloaded (see "Unloading the... -
Page 37: Interrupting A Programme
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as Important: the door is opened. If the detergent dispenser flap has If the door is closed again, the already opened, do not change the programme will continue from the point programme. -
Page 38: Additional Functions
Additional functions Factory default setting The Wash/Rinse indicator light shows whether a setting other than the factory If you have altered any settings from default setting has been set. the factory default, you can re-set them back to the factory default settings as –... -
Page 39: Cleaning And Care
Cleaning and care ^ When the dishwasher is being loaded, Check your dishwasher regularly food and drink residues may drip onto (approx. every 4 - 6 months). This the sides of the dishwasher door. way faults and problems can be These surfaces are outside the wash avoided. -
Page 40: Cleaning The Filters In The Wash Cabinet
Cleaning and care Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. The dishwasher must not be used without all the filters in place. - Page 41 Cleaning and care ^ Replace the filter combination so that To clean the inside of the filter, the flap must be opened: it lies flat in the base of the wash cabinet. ^ Press catches a together in the ^ Then turn the handle clockwise to direction of the arrows as shown, and open the filter b.
-
Page 42: Cleaning The Spray Arms
Cleaning and care ^ Remove the lower basket. Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. -
Page 43: Problem Solving Guide
Problem solving guide With the aid of the following guide, minor problems can be easily corrected without calling in a Miele service technician, saving you both time and money. Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations. - Page 44 Problem solving guide Problem Possible cause Remedy The Wash/Rinse, There may be a technical – Clean the water inlet filter Drying and End fault. and clean the drain pump indicator lights flash and non-return valve as simultaneously. described in "Maintenance". If this does not resolve the problem, –...
-
Page 45: The Dishwasher Does Not Fill/Drain
Problem solving guide The dishwasher does not fill/drain. Problem Possible cause Remedy The Inlet/Drain check The stopcock is Open the stopcock fully. indicator flashes. closed. The dishwasher stops Before rectifying the problem during a programme. you must: The Inlet/Drain – Switch the dishwasher off indicator flashes. -
Page 46: General Problems
Problem solving guide General problems Problem Possible cause Remedy Detergent residue is left The dispenser was still Make sure the dispenser is in the dispenser at the damp when detergent dry before adding end of a programme. was added. detergent. The detergent Clogged detergent Clean the detergent from... -
Page 47: Noises
Problem solving guide Noises Problem Possible cause Remedy Knocking noise in the A spray arm is knocking Interrupt the programme, wash cabinet. against an item in a and rearrange the items basket. which are obstructing the spray arm. Rattling noise in the Items of crockery are Interrupt the programme, wash cabinet. -
Page 48: Unsatisfactory Washing Result
Problem solving guide Unsatisfactory washing result Problem Possible cause Remedy The dishes are not The dishes were not loaded See notes in "Loading the clean. correctly. dishwasher" The programme was not Select a more intensive powerful enough. programme. See Programme chart. - Page 49 Problem solving guide Problem Possible cause Remedy Dishes, cutlery The amount of rinse aid Replenish the reservoir, and glasses are may be insufficient, or the increase the dosage or not dry or are rinse aid reservoir empty. change the brand of rinse aid. flecked.
- Page 50 Problem solving guide Problem Possible cause Remedy Glassware has a This may be caused by the Change your detergent. brown or blue tinge, detergent. and film cannot be wiped off. Glassware is dull and The glasses are not There is no remedy. discoloured;...
-
Page 51: Maintenance
^ Replace the filter and seal, making union. This filter is available from the Miele Spares Parts dept. sure they are sitting correctly. ^ Reconnect the inlet hose to the Cleaning the filter:... -
Page 52: Cleaning The Drain Pump And Non-Return Valve
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. -
Page 53: Comparison Tests
Comparison tests Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for energy label comparison tests: Normal Capacity: 12/14 place settings (depending on model) Amount of detergent: 12 place settings: in compartment I, 25 g in compartment II 14 place settings: in compartment I, 27,5 g in compartment II Rinse aid dispensing:... - Page 54 Comparison tests Model types G 1xxx with a cutlery tray (12 place settings): Upper basket Lower basket Cutlery tray...
- Page 55 Comparison tests Model types G 2xxx with a cutlery tray (14 place settings): Lower basket Upper basket Cutlery tray...
-
Page 56: Programme Overview
Programme overview Programme When to use Sensor wash Sensor controlled programme for normally soiled crockery Normal For normally soiled crockery with dried on soiling; includes glass care system. Quick wash "Quick programme" for lightly soiled crockery, e.g. party crockery; for flushing out salt residues after replenishing the salt reservoir; includes glass care system;... - Page 57 Programme overview Programme sequence Consumption Duration Energy Water Pre- Main Interim Final Drying Cold Litres Cold wash wash rinse rinse water water water water °C °C connec- connec- connec- connec- tion tion tion tion (20 °C) (60 °C) (20 °C) (60 °C) h:min h:min...
-
Page 58: After Sales Service
Programme Correction) is designed to contact: enable a service technician to update your appliance's electronics in keeping – Your Miele Chartered Agent, or with advances in technology. – the Miele Service Department (see The "PC" indicator light is used as the back cover for address). -
Page 59: Optional Accessories
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele Chartered Agent or the Spare Parts Department (some may be supplied as stan- dard, depending on model). If you would like to …... -
Page 60: Electrical Connection
A (AUSTRALIA). ^ Do not connect via an extension lead. WARNING: THIS APPLIANCE If the connection cable is MUST BE EARTHED damaged it must be replaced with a complete connection box and cable by a Miele approved service technician only. -
Page 61: Plumbing
Providing your dishwasher has been supply without an extra non-return installed correctly, the Miele waterproof valve if national regulations allow anti-leak system will protect you from this. water damage throughout its lifetime. -
Page 62: Connection To The Water Supply
Plumbing The inlet hose must not be shortened or damaged in any way as it contains electrical components (see illustration). This appliance incorporates back- flow protection complying with AS/NZS 3500.1.2. No further backflow protection required for connection to the water supply. -
Page 63: Drainage
Plumbing Drainage Venting the drainage system – The appliance drainage system is If the on-site drain connection is fitted with a non-return valve, which situated lower than the guide path for prevents dirty water from flowing the bottom basket rollers in the open back into the dishwasher via the door, the drainage system must be drain hose. -
Page 64: Technical Data
Technical data Dishwasher model G 1XXX G 2XXX Height freestanding 84.5 cm (adjustable +3.5 cm) Height built-in 80.5 cm 84.5 cm (adjustable + 6.5 cm) (adjustable + 6.5 cm) Height of building-in Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) recess Width 59.8 cm... - Page 68 Alteration rights reserved/ M.-Nr. 07 066 491 / 00 G1142/1152/G2142/2152 / 1308...