Download Print this page

Lennox Eyebrow Lintel Kit ELDV-35 Installation Instructions

Eyebrow lintel lkits for use with eldv-35, eldv-40 & eldv-45 direct vent gas fireplaces

Advertisement

Quick Links

FOR USE WITH ELDV-35, ELDV-40 & ELDV-45 DIRECT VENT GAS FIREPLACES
KIT CONTENTS:
1 ea. Eyebrow
1 ea. Lintel
3 ea. #10 Screws
1 ea. Instruction Sheet
Eyebrow Lintel Kits
CAT. NO.
MODEL NO.
H4387
ELDV35
H4388
ELDV40
H4389
ELDV45
Table 1
HEARTH PRODUCTS
KITS AND ACCESSORIES
750,235M
EYEBROW LINTEL KITS
Rev. NC, 07/2006
INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS
FOR USE WITH ELDV-35, ELDV-40 & ELDV-45 DIRECT VENT GAS FIREPLACES
KIT CONTENTS:
TOOLS NEEDED:
INSTALLATION INSTRUCTIONS
1 ea. Eyebrow
5/16" Nut Driver or Socket
1 ea. Lintel
Step 1. Remove glass door assembly per the following instrucitons.
#26 (.147") Drill Bit
3 ea. #10 Screws
Drill Motor
1 ea. Instruction Sheet
WARNING
Eyebrow Lintel Kits
Handle this glass with extreme care! The glass panel is
CAT. NO.
MODEL NO.
WHERE USED
susceptible to damage — do not scratch while handling
ELDV-35
or while re-installing the glass door frame.
ELDV-40
ELDV-45
WARNING
Table 1
Do not operate appliance with the glass front removed,
cracked or broken. Replacement of the glass should be
done by a licensed or qualifi ed service technician.
Lintel
Glass Door Removal Procedure:
Refer to Figure 2 and remove the front glass enclosure panel as
follows:
Eyebrow
1. Remove the bottom compartment door by lifting and pulling it towards
the front of the fi replace.
Instruction Sheet
Screws
2. Locate the two (2) latches at the top of the control compartment
and disengage them from the fl oor frame bottom Vee-fl ange, pulling
Figure 1 - Kit Contents
down on their handles to open them.
3. Swing the bottom of the door out and raise it slightly to lift the top
fl ange of the door frame away from the appliance.
IMPORTANT
INSTALL ONLY WHEN APPLIANCE IS OFF AND COLD!
GENERAL INFORMATION
These eyebrow lintel kits are designed to provide an aesthetically pleasing
appearance and conceal the gap above the fi replace.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
HOMEOWNER'S MANUALS PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local distribu-
tor or dealer.
Door
Assembly
Bottom Panel
Figure 2 - Glass Door Removal and Reinstallion.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Instruction Sheet
Figure 1 - Kit Contents
IMPORTANT
INSTALL ONLY WHEN APPLIANCE IS OFF AND COLD!
GENERAL INFORMATION
These eyebrow lintel kits are designed to provide an aesthetically pleasing
appearance and reduces the gap above the fi replace.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
HOMEOWNER'S MANUALS PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local distribu-
tor or dealer.
INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS
TOOLS NEEDED:
5/16" Nut Driver or Socket
#26 (.147") Drill Bit
Drill Motor
WHERE USED
ELDV-35
ELDV-40
ELDV-45
Lintel
Eyebrow
Screws
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
750,235M
Rev. NC, 08/2006
INSTALLATION INSTRUCTIONS
Step 1. Remove glass door assembly per the following instructions.
Handle this glass with extreme care! The glass panel is
susceptible to damage — do not scratch while handling
or while re-installing the glass door frame.
Do not operate appliance with the glass front removed,
cracked or broken. Replacement of the glass should be
done by a licensed or qualifi ed service technician.
Glass Door Removal Procedure:
Refer to Figure 2 and remove the front glass enclosure panel as
follows:
1. Remove the bottom compartment door by lifting and pulling it towards
the front of the fi replace.
2. Locate the two (2) latches at the top of the control compartment
and disengage them from the fl oor frame bottom Vee-fl ange, pulling
down on their handles to open them.
3. Swing the bottom of the door out and raise it slightly to lift the top
fl ange of the door frame away from the appliance.
Door
Assembly
Figure 2 - Glass Door Removal and Reinstallation.
HEARTH PRODUCTS
KITS AND ACCESSORIES
EYEBROW LINTEL KITS
WARNING
WARNING
Bottom Panel
1

Advertisement

loading

Summary of Contents for Lennox Eyebrow Lintel Kit ELDV-35

  • Page 1 INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS FOR USE WITH ELDV-35, ELDV-40 & ELDV-45 DIRECT VENT GAS FIREPLACES KIT CONTENTS: TOOLS NEEDED: 1 ea. Eyebrow 5/16” Nut Driver or Socket 1 ea. Lintel #26 (.147") Drill Bit 3 ea. #10 Screws Drill Motor 1 ea.
  • Page 2 Step 2. Using a 5/16" socket or nutdriver, remove the existing lintel as shown in Figure 3. Retain the screws for Step 3. Lintel Figure 3 - Removing Lintel Step 3.Install the new lintel provided using the screws that were removed in step 2 (reversing instructions in step 2 and see Figure 3).

This manual is also suitable for:

Eldv40Eldv45H4387H4388H4389