Related Manuals for Lanzar OPTIDRIVE OPTIX-10OPTIX-10
Summary of Contents for Lanzar OPTIDRIVE OPTIX-10OPTIX-10
- Page 1 u s e r ’ s m a n u a l 10-Channel Active www.lanzar.com Electronic Crossover Network OptiX-10 OptiX-10 with Subwoofer Level Control...
- Page 2 I N T R O D U C T I O N . . . Congratulations on your purchase of a new Lanzar Opti signal processor. Opti mobile electronics are some of the most advanced car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising musical service.
-
Page 3: Table Of Contents
t a b l e o f c o n t e n t s general features precautions features and specifications 7-11 system wiring 12-13 mounting and installation noise check and system adjustment troubleshooting... -
Page 4: General Features
g e n e r a l f e a t u r e s 10 Crossover Channels Blue Light Illumination 4 Channel Inputs Signal Pass-through for Additional Processors Remote Bass Level Control High Channels: Separate Front and Rear Frequency and Gain Controls Mid Channels: Separate Front and Rear Frequency and Gain Controls Sub Channels: Frequency and Gain Control Selectable Q Settings for Front and Rear Channels... -
Page 5: Precautions
P r e c a u t i o n s To prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly. Reinstate all car parts that were removed. -
Page 6: Features And Specifications
f e a t u r e s a n d s p e c i f i c a t i o n s... - Page 7 1. F/R INPUT SWITCH In the “2CH” position, rear inputs are split and directed to the front and rear channels simultaneously. This feature should be used when the head unit has only one pair of output jacks.If the source unit has independent front and rear channel outputs, disengage the parallel input by sliding the switch to the “4CH”...
- Page 8 11. Rear Channel Output Terminals 12. Subwoofer Output Terminals 13. Subwoofer Level Remote Control This terminal may be used to connect the Remote Subwoofer Level Control. This enables Terminal the user to have easy access to adjust the bass levels to compensate for increased road noise or recording variations.
-
Page 9: System Wiring
2-CHANNEL 3 WAY SYSTEM S y s t e m w i r i n g REMOTE OUTPUT from HEAD UNIT Head unit (Stereo, DVD Player, Tape Deck, etc.) TO LINE OUT OF HEAD UNIT BATTERY GROUND TO SUB TO REAR OUTPUT OUTPUT REAR CHANNEL... - Page 10 S y s t e m w i r i n g 2-CHANNEL MULTIPLE CROSSOVER SYSTEM...
- Page 12 4 CHANNEL 4 WAY SYSTEM S y s t e m w i r i n g REMOTE OUTPUT from HEAD UNIT TO FRONT & REAR OUT OF HEAD UNIT BATTERY GROUND TO SUB TO REAR TO REAR OUTPUT MID OUT HIGH OUT REAR MID-WOOFER REAR TWEETER...
- Page 13 6-CHANNEL 5-WAY SYSTEM S y s t e m w i r i n g REMOTE OUTPUT from HEAD UNIT Head unit (Stereo, DVD Player, Tape Deck, etc.) TO FRONT, REAR & SUB OUT OF HEAD UNIT BATTERY GROUND TO SUB TO REAR TO REAR OUTPUT...
-
Page 14: Mounting And Installation
M o u n t i n g a n d i n s t a l l a t i o n Your new Opti Series crossover comes complete with all required mounting hardware. Please read the Installation Precautions section below before installing your Lanzar Opti signal processor, and then refer to the diagrams provided to connect power, audio input and output connections according to your own system configuration requirements. - Page 15 Processor Installation 1. Find a suitable location in the vehicle to mount the processor. The X-10 is a trunk mount unit and it should be installed in close proximity to your amplifier system on the amp rack. You should pick a location that offers easy access to the unit for adjustment. 2.
-
Page 16: Noise Check And System Adjustment
N o i s e c h e c k a n d s y s t e m a d j u s t m e n t NOISE CHECK Check the entire audio system for noise before permanently securing the CROSSOVER mounting 1. -
Page 17: Troubleshooting
T B O U B L E S H O O T I N G G U I D E PROBLEM 1. There is an audible distortion at a low volume level. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running. - Page 18 All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for three (3) years from the date of purchase. This warranty is limited to the original retail purchaser of the Signal Processor. Should the unit fail due to a factory defect in material or workmanship, your unit will be repaired or replaced at the sole discretion of Lanzar.