Sharp LC-32FH500E Service Manual page 20

LC-32FH500
LC-32FH510
Page Line Sub
Page
01/17 [SHARP FACTORY MENU
7
09/17
8
10/17
11/17
9
12/17
10
13/17
Item
ETC EEP, Autoinstallation, Op-
EEP Clear
EEP Clear B
Standby cause reset
Autoinstallation SW
Pattern
L Error Reset
L Error Check
I2C OFF
Sharp protocol
PUBLIC MODE (1/2) PUBLIC MODE Submenu
Power On fi xed
Maximum volume
Volume fi xed
Volume fi xed Level
RC button
Panel button
Menu button
On screen display
Input mode start
Input mode fi xed
Input TV mode program
number
RC path through
PUBLIC MODE (2/2) PUBLIC MODE Submenu
Hotel mode
Reset
Execute
SMART LOADER SMART LOADER Sub-
menu
Save settings to USB
Load settings from USB
ADC ADJUST
MODE
ADJUST
R-GAIN
G-GAIN
Description Remarks (adjustment details, etc.)
Press "OK" to enter to ETC Submenu
tion, Country, L Error...
Clear NVM data
Clear NVM data (except adjustments area).
Reset of STANDBY CAUSE.
Off On: Pending to execute on next power on. Off: Not required.
0 Selection of internal pattern from 0 up to 6...
0 LAMP ERR RESET Initialization of L_ERR.
L_ERR detection. 0: activated. 1: deactivated.
On
I2C BUS status. On: free BUS. Off: Normal.
Off
On Remote Control Protocol. On: SHARP Off: MSTAR.
Press "OK" to enter to PUBLIC MODE Sub-
menu
Variable
Press "
60
Press "
Variable Press "
20
Respond
Press "
Respond Press "
Respond
Press "
On
Press "
Normal
Press "
Variable
Press "
Normal
Off
Press "
module)
Off
Press "
Press "
Press "
played).
Press "OK" to enter to SMART LOADER Sub-
menu
Press "
Press "
ADC ADJUST Submenu Press "OK" to enter to ADC ADJUST Submenu
YPbPr(SD)
Press "
External singal
Press "
External: factory. Internal: service
65
Press "
66
Press "
20
◄ ►
" or " " to change Variable/Fixed.
◄ ►
" or " " to change 0/60.
◄ ►
" or " " to change Variable/Fixed.
◄ ►
Press " " or " " to change 0/60.
◄ ►
" or " " to change Respond/No respond.
◄ ►
" or " " to change Respond/No respond.
◄ ►
" or " " to change Respond/No respond.
◄ ►
" or " " to change On/Off.
◄ ►
" or " " to change Normal/TV/SCART1/...
◄ ►
" or " " to change Variable/Fixed.
◄ ►
" or " " to change On/Off (required external
◄ ►
" or " " to change On/Off.
◄ ►
" or " " to return to factory settings.
◄ ►
" or " " to confirm ("OK" will be dis-
◄ ►
" or " " to Save.
("OK" or "NO USB drive available, please check
and/or insert USB dri..." will be displayed).
◄ ►
" or " " to Load.
("OK, reboot TV set" or "NO USB drive avail-
able, please check and/or insert USB dri..."
will be displayed).
◄ ►
" or " " to change RGB/YPbPr(SD)/ YPbPr(HD).
◄ ►
" or " " to change Internal signal/External signal.
◄ ►
" or " " for manual adjustment.
◄ ►
" or " " for manual adjustment.